Clarke CAX2TA Manuel utilisateur

INSTRUCTIONS

GC0119 - ISS 2

MODEL NO: CAX2TA

PART NO: 7600010

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY WARNINGS

For your own safety and that of others around you, please read and observe

these safety instructions.

A warning label is attached to each stand and should be replaced if it is

removed or damaged. A replacement label can be obtained from your

Clarke dealer.

The following precautions are for guidance only. If you are in any doubt about

the use of these stands, please contact the Clarke International Service

Department for advice.

1. ALWAYS refer to the vehicle manufacturer’s instructions before raising the

vehicle.

2. ALWAYS ensure the working area is safe, i.e. not on the highway etc.

3. Do not use the axle stands on uneven ground.

4. ALWAYS ensure the vehicle is securely chocked before use.

5. ALWAYS ensure, before laying underneath the vehicle, a responsible person

is made aware in case of injury or accident.

6. ALWAYS ensure it is not possible under any circumstances, for the vehicle to

move, before getting underneath the vehicle.

7. NEVER allow children or animals to play in or near the area.

8. NEVER leave the vehicle on axle stands where it could be considered a

hazard to others.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

9. Do not overload the stands.

10. Never use more than a single pair of stands.

11. Only use on a hard level surface e.g. concrete.

12. Securely chock wheels remaining on the ground.

13. Make sure that each stand is securely located under a strong point on the

vehicle; consult the user’s handbook for guidance.

14. Lower the vehicle onto the stands slowly and gently.

15. Exercise extra care when using with a three wheeled vehicle or trailer.

16. Upper and lower columns are to be used only as a pair supplied.

17. It must be ensured that the vehicle/load is carefully located on the centre

of the axle stand saddle. Failure to do this can result in damage to the axle

stands, loss of support to the load, serious personal injury or loss of life.

ASSEMBLY

1. Slide the column into the base as

shown.

• If required remove the bolt (2) in

the base.

2. Slide the bolt into position and

secure using the nut supplied.

USING THE AXLE STANDS

1. Remove the locking pin.

2. Adjust the height of the axle stand.

3. Replace the locking pin.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SPECIFICATION

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Maximum Height 390 mm

Minimum Height 265 mm

Maximum Load 3 Tonnes per pair (1.5 tonnes each)

Product Weight 4.4 kg

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Jack

Clarke

Clarke Strong-Arm CBJ2B Guide de dépannage

Clarke

Clarke Strong-Arm CTJ5GLS Mode d’emploi

Clarke

Clarke CTT320 Manuel utilisateur

Clarke

Clarke Strong Arm CTJ3000GB Mode d’emploi

Clarke

Clarke strong-arm CBJ30 Guide de dépannage

Clarke

Clarke CTJ2000A Manuel d'installation et d'exploitation

Clarke

Clarke CTJ1800A Mode d’emploi

Clarke

Clarke STRONG-ARM CTJ10GLB Mode d’emploi

Clarke

Clarke STRONG-ARM CHDDWD Manuel

Clarke

Clarke CTJ2000LPB Mode d’emploi

Clarke

Clarke CBJ32 Mode d’emploi

Clarke

Clarke STRONG-ARM CTJ2B Mode d’emploi

Clarke

Clarke CGK4 Manuel utilisateur

Clarke

Clarke Strong-Arm CTJ1500QULP Mode d’emploi

Clarke

Clarke CTJ1800AB Mode d’emploi

Clarke

Clarke STRONG-ARM CTJ3000G Manuel utilisateur

Clarke

Clarke CTJ30 Guide de dépannage

Clarke

Clarke Strong-Arm CTJ 50 Manuel d'installation et d'exploitation

Clarke

Clarke STRONG-ARM CTJ1250A Manuel utilisateur

Clarke

Clarke CFJ60 Manuel utilisateur

Clarke

Clarke CTJ3GLS Mode d’emploi

Clarke

Clarke STRONG-ARM CTJ2QLP Mode d’emploi

Clarke

Clarke CTJ2500SUV Mode d’emploi

Clarke

Clarke Strong-Arm CTJ2CBB Mode d’emploi

Manuels Jack populaires d'autres marques

Omega Lift Equipment

Omega Lift Equipment 18122C Instructions d'utilisation

Pittsburgh

Pittsburgh 58816 Instructions de montage

Unimec

Unimec TP Manuel utilisateur

Sonic

Sonic 4800703 Manuel utilisateur

BGS technic

BGS technic 70039 Manuel utilisateur

TradeQuip

TradeQuip 1128T Manuel utilisateur

VEVOR

VEVOR TJD-12000SP-F Manuel utilisateur

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuel utilisateur

Stels

Stels 51131 Manuel utilisateur

Bushranger

Bushranger RJX01 Manuel utilisateur

Valex

Valex 1650520 Manuel utilisateur

Pfaff

Pfaff Merkur M0 Manuel utilisateur

Beta

Beta 3050/K Supplément

Sealey

Sealey 1050CXHV Manuel utilisateur

Jung

Jung JH Series Manuel utilisateur

URIAH

URIAH UC200020 Manuel utilisateur

Kennedy

Kennedy KSJ010 Manuel utilisateur

Grizzly

Grizzly H8097 Manuel utilisateur