Clarke CTJ1800AB Mode d’emploi

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0122

1.8 TONNE ALUMINIUM RACING JACK

MODEL NO: CTJ1800AB

PART NO: 7623201

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE 1.8 Tonne aluminium racing jack.

Before attempting to use this product, please read this manual thoroughly and

follow the instructions carefully. In doing so you will ensure the safety of yourself

and that of others around you, and you can look forward to your purchase

giving you long and satisfactory service.

SPECIFICATIONS

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

Model number CTJ1800AB

Part number 7623201

Length (not including handle) 640 mm

Width (not including wheels) 300 mm

Height 230 mm

Height of saddle (minimum) 85 mm

Height of saddle (maximum) 465 mm

Weight 19 kg

Rated Load 1.8 tonne(1800kg)

Cup diameter 115mm

Pump oil capacity 190ml

Distance per pump action 80mm

Pump actions to max height 5

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

1. Read Instruction manual before use.

2. Only trained persons should operate this lifting equipment.

3. ALWAYS ensure that sufficient light is provided and that the work area is

kept clear of unrelated items.

4. ALWAYS inspect the jack before use. Make sure that all parts are in good

condition and operating smoothly and that no cracks or distortion is

apparent. If in doubt DO NOT use. Have the damaged parts replaced or

consult your CLARKE dealer.

5. The jack must be maintained and repaired by suitably qualified persons.

6. DO NOT make any modifications to this jack or adjust any valves.

7. DO NOT use the jack if an oil leak is apparent. Consult your CLARKE dealer.

8. DO NOT use to lift people and ensure that no-one is in the vehicle during

lifting.

9. NEVER exceed the rated load for the jack See “Specifications” on page ..

Overloading can cause the jack to fail resulting in personal injury.

10. Make sure that the jack is on a hard level surface, and there is no possibility

of it slipping when under load.

11. Only use the jack on solid ground, preferably concrete. Avoid tarmac as

the jack could sink in.

12. Make sure the load is taken by the full saddle and that the lifting point on

the load is of sufficient strength to support the weight.

13. ALWAYS use axle stands to stabilise the load once lifted.

14. Consult the vehicle handbook to determine the correct lifting points.

15. Ensure the load is chocked and the handbrake applied before lifting.

16. NEVER work on or under a load unless it is fully and adequately supported.

17. NEVER rely upon the jack to hold the load in position.

18. NEVER push a load off the jack.

19. Ensure that all personnel are well clear of a load being raised or lowered.

20. Take care not to trap fingers within the moving parts.

21. Use only as a lifting device, do not use as a dolly to move a load.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

UNPACKING AND ASSEMBLY

ASSEMBLY

1. Insert the lower half of the jack

handle into position as shown.

• Make sure that the square bar

inside the handle yoke

engages with the hole in the

jack handle.

2. Secure the handle by tightening

the thumbscrew shown.

3. Remove the travel retaining block

by pressing the handle yoke

downwards and pulling the block

away.

• Take car not to trap fingers

while doing this.

4. Fit the upper jack handle to the

lower jack handle as shown.

• Make sure that the ball clip

engages with the hole in the

lower jack handle.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

POSITIONING

Ensure the vehicle is chocked and stable and on firm level ground.

1. Turn the jack handle counterclockwise, to lower the lifting ram.

2. Position the jack so that the saddle is directly beneath the lifting point and

that there are no obstacles to prevent a clean lift, also, make sure that all

personnel are well away from the area, before raising the vehicle.

LIFTING

1. Close the release valve by turning the jack handle clockwise firmly.

2. Operate the jack by pumping the jack handle.

• Make sure that the saddle is in full contact with the vehicle lifting

point and that there are no obstacles to prevent a clean lift.

3. Place axle stands beneath the vehicle.

• Make sure that the axle stands are centred under the vehicle

support points and are perfectly stable before full weight is taken.

• Make sure that the axle stands are in good condition and capable

of supporting the load.

• Make sure that the axle stands cannot move when supporting the

load and that they are on a firm level surface.

• DO NOT jerk the handle, ensure it lowers slowly and under complete

control on to the axle stands which must be correctly positioned and

take the weight evenly.

NOTE: The jack may move slightly during operation. It is therefore

important that the immediate vicinity is clean and completely

free from clutter.

LOWERING

1. Lift the vehicle slightly to remove the weight from any supports.

2. Remove any supports from beneath the vehicle.

3. Slowly turn the jack handle counterclockwise to open the release valve.

NOTE: make sure that this operation is carried out under complete

control. DO NOT allow the load to drop suddenly as this could

damage internal components.

4. Remove the jack from beneath the vehicle.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MAINTENANCE

1. When the jack is not in use, keep the saddle lowered and the release valve

closed (jack handle turned fully clockwise).

2. Keep the jack clean and apply lubricating oil to all pivoting sections every

three months, or more often when it is used in a dusty work environment.

3. Check the pump piston and piston rod periodically for signs of rust or

corrosion. Clean exposed area with clean oiled cloth.

4. Change the oil once a year or as required, See page 7.

STORAGE

Store in a dry place, with the ram fully retracted. If stored for long periods,

inspect at least once a year, clean and re-oil. For servicing, contact your

CLARKE dealer or CLARKE International Service Department.

BLEEDING THE HYDRAULIC SYSTEM

1. Put the jack on horizontal ground.

2. Open the release valve by

SLOWLY turning the jack handle

counterclockwise and then pump

the handle up and down several

times.

3. Loosen the fill screw.

4. Pump the jack handle up and

down slowly several times to

purge the air from the hydraulic

system.

5. Tighten the fill screw.

WARNING: DO NOT ADJUST THE PRESSURE RELIEF SCREWS UNDER ANY

CIRCUMSTANCES

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TOPPING UP OR CHANGING THE OIL

1. Lower the saddle as far as possible.

2. Remove ONLY the filling screw as

shown on the right.

3. Turn the jack over and drain the

oil into a suitable container.

• Dispose of the oil in

accordance with government

regulations.

4. Fill with CLARKE hydraulic oil into

the fill screw hole slowly until the

oil reaches the bottom of the thread in the oil fill hole.

• CLARKE Hydraulic oil is available from your local CLARKE dealer.

NOTE: Do not touch the assembled handle when adding the hydraulic

oil.

5. Replace the filling screw.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TROUBLESHOOTING

If any of these remedies fail to restore your jack, consult your CLARKE dealer.

PROBLEM CAUSE SOLUTION

Jack will not lift the

rated load

Low oil level See “Topping up or Changing the oil”

on page 7.

Release valve not

closed

Turn the jacking handle fully

clockwise.

Jack lowers when

under load

Release valve not

closed

Turn the jacking handle fully

clockwise.

Air in the hydraulic

system

Bleed the system. See page 6.

Pump feels spongy Low oil level See “Topping up or Changing the oil”

on page 7.

Air in the hydraulic

system

Bleed the system. See page 6.

Handle raises or

flies back under

load

Air in the hydraulic

system

Bleed the system. See page 6.

Jack will not lift full

height

Low oil level See “Topping up or Changing the oil”

on page 7.

Air in the hydraulic

system

Bleed the system. See page 6.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DECLARATIONS OF CONFORMITY

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

COMPONENT PARTS - (GENERAL ASSEMBLY)

No Description No Description

1 Saddle Pad 29 Screw

2 Saddle Screw 30 Washer

3 Saddle 31 Screw

4 Saddle Base 32 Rear Caster

5 Hinge Pin 33 Rear Caster Base

6 Circlip 34 Washer

7 Front Axle 35 Spring Clip

8 Side Plate 36 Spring

9 Front Wheel Bush 37 Circlip

10 Front Wheel 38 Trunnion Arm

11 Front Wheel Washer 39 Hydraulic Unit

12 Nut 40 Handle Sleeve

13 Side Carrying Handle 41 Upper Handle

14 Screw 42 Lower Handle

15 Washer 43 Handle Set Screw

16 Screw 44 Circlip

17 Support Pivot Bar 45 Roller

18 Screw 46 Roller Pin

19 Arm Stop Bar 47 Handle Yoke

20 Saddle Base Pin 48 Handle Yoke Pivot Pin

21 Spacer 49 Tie Rod

22 Arm Side Plate 50 Lift Arm Pivot Rod

23 Screw 51 Rubber Bumper

24 Washer 52 Split Pin

25 Split Washer 53 Trunnion Block

26 Screw 54 Hinge Bush

27 Nut 55 Connection Block

28 Screw M10X35 56 Hinge Pin

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Jack

Clarke

Clarke Strong-Arm CTJ2CBB Mode d’emploi

Clarke

Clarke Strong-Arm CTJ1500QULP Manuel d'installation et d'exploitation

Clarke

Clarke CGK4 Manuel utilisateur

Clarke

Clarke CTT320 Manuel utilisateur

Clarke

Clarke STRONG-ARM CTJ3000QLB Mode d’emploi

Clarke

Clarke CTJ1800A Mode d’emploi

Clarke

Clarke STRONG-ARM CHDDWD Manuel

Clarke

Clarke CFJ48 Manuel d'installation et d'exploitation

Clarke

Clarke CBJ32 Mode d’emploi

Clarke

Clarke CTJ2000A Manuel d'installation et d'exploitation

Clarke

Clarke CTJ2000G Manuel utilisateur

Clarke

Clarke CTJ10GLS Mode d’emploi

Clarke

Clarke STRONG-ARM CFJ48B Manuel utilisateur

Clarke

Clarke CAX2TA Manuel utilisateur

Clarke

Clarke Strong-Arm CBJ2B Guide de dépannage

Clarke

Clarke Strong-Arm CTJ2250LP Mode d’emploi

Clarke

Clarke CTJ2000LPB Mode d’emploi

Clarke

Clarke CTJ2000LP Mode d’emploi

Clarke

Clarke STRONG-ARM CTJ2QLP Mode d’emploi

Clarke

Clarke STRONG-ARM CTJ2LP Mode d’emploi

Clarke

Clarke STRONG-ARM CTJ10GLB Mode d’emploi

Clarke

Clarke Strong Arm CTJ3000GB Mode d’emploi

Clarke

Clarke STRONG-ARM CTJ5GLB Mode d’emploi

Clarke

Clarke CTJ3GLS Mode d’emploi

Manuels Jack populaires d'autres marques

Omega Lift Equipment

Omega Lift Equipment 18122C Instructions d'utilisation

Pittsburgh

Pittsburgh 58816 Instructions de montage

Unimec

Unimec TP Manuel utilisateur

Sonic

Sonic 4800703 Manuel utilisateur

BGS technic

BGS technic 70039 Manuel utilisateur

TradeQuip

TradeQuip 1128T Manuel utilisateur

VEVOR

VEVOR TJD-12000SP-F Manuel utilisateur

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuel utilisateur

Stels

Stels 51131 Manuel utilisateur

Bushranger

Bushranger RJX01 Manuel utilisateur

Valex

Valex 1650520 Manuel utilisateur

Pfaff

Pfaff Merkur M0 Manuel utilisateur

Beta

Beta 3050/K Supplément

Sealey

Sealey 1050CXHV Manuel utilisateur

Jung

Jung JH Series Manuel utilisateur

URIAH

URIAH UC200020 Manuel utilisateur

Kennedy

Kennedy KSJ010 Manuel utilisateur

Grizzly

Grizzly H8097 Manuel utilisateur