Clarke Devil 6003 Manuel
OPERATING & MAINTENANCE
INSTRUCTIONS
Devil 6003, 6005, 6009 & 6015
Part Nos: 6925220, 6925225, 6925230 & 6925235
GC0110
ELECTRIC FAN HEATERS
2
INTRODUCTION
Thank you for purchasing this CLARKE Electric Fan Heater.
Please read this manual thoroughly and follow the instructions carefully.
Before attempting to use the heater, thoroughly familiarise yourself with the
heater & its operation. In doing so you will ensure the safety of yourself and
that of others around you, and you can look forward to the heater giving you
long and satisfactory service.
GUARANTEE
This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.
This guarantee does not effect your statutory rights.
ENVIRONMENTAL PROTECTION
Do not dispose of this product with general household waste. It must
be disposed of according to the laws governing Waste Electrical and
Electronic Equipment, at a recognised disposal facility.
3
TABLE OF CONTENTS
INTRODUCTION ..................................................................................2
GUARANTEE ........................................................................................2
ENVIRONMENTAL PROTECTION .........................................................2
TABLE OF CONTENTS ..........................................................................3
GENERAL SAFETY RULES .....................................................................4
ELECTRICAL CONNECTIONS .............................................................. 6
OPERATION ......................................................................................... 8
MAINTENANCE ...................................................................................10
FAULT FINDING ...................................................................................11
PARTS LISTS & DIAGRAMS ..................................................................12
WIRING DIAGRAMS ...........................................................................16
TECHNICAL SPECIFICATION ...............................................................18
SPARE PARTS & SERVICING CONTACTS .............................................18
DECLARATION OF CONFORMITY.......................................................19
4
GENERAL SAFETY RULES
1) WORK AREA
1. These heaters are for INDOOR USE ONLY.
2. Do not expose the heater or power cable to rain or wet conditions. Any
water entering the heater will increase the risk of electric shock. DO NOT
use this heater in a bathroom, shower room, in the vicinity of a swimming
pool, or any wet environment.
3. NEVER locate the heater near combustible materials such as curtains,
furniture etc. Allow at least 1 metre clearance.
4. DO NOT locate the heater close to an adjacent wall or ceiling. Allow a
distance of at least 1 metre from a wall or ceiling. Avoid placing the
heater directly below socket outlets.
5. Take care to ensure that the grille cannot be blocked by curtains or other
fabrics.
6. Do not operate fan heaters in explosive atmospheres such as in the
presence of flammable liquids, gases or dust such as in a paint spray
booth or any explosive environment. Electric motors create sparks which
may ignite dust or fumes.
7. Never place the heater on a movable vehicle where it could be tipped
over.
8. Do not allow the heating elements to become covered with dust which
could become a fire hazard. If used in a dusty workplace it should be
cleaned as described under Cleaning and Maintenance.
9. NEVER touch the heater element for at least 15 minutes after switching off.
10. DO NOT leave the heater unattended.
11. If children are present always use with a fireguard.
12. Store the fan heater out of the reach of children and do not allow persons
unfamiliar with these instructions to operate this appliance.
13. Do not use this heater with a programmable timer used to switch it on
automatically.
2) ELECTRICAL SAFETY
1. Electrical appliances must match the power outlet. Never modify the plug
in any way. Do not use adaptor plugs with earthed (grounded) appli-
ances. Correct plugs and outlets will reduce the risk of electric shock.
2. Do not abuse the electrical cable. Never use the cord for pulling or
unplugging the heater. Keep the cable away from sources of heat, oil,
sharp edges or moving parts. Damaged or tangled cables increase the
risk of electric shock.
5
3. Keep the mains cable well away from machines and ensure an adequate
electrical supply is close at hand so that the operation is not restricted by
the length of the cable.
4. ALWAYS disconnect from the mains supply before moving the heater or
performing any maintenance tasks.
5. ALWAYS use ONLY in an upright position.
6. Inspect the mains cable regularly for signs of damage. DO NOT use if it is
damaged, and ALWAYS keep it away from the source of heat.
7. Check the fan heater for damage before use. DO NOT use if the heater
elements are damaged or broken. Any damage should be properly
repaired or the part replaced. If in doubt, DO NOT use the machine.
Consult your local dealer.
3) SERVICE & REPAIRS
1. When necessary, have your appliance repaired by a qualified person
using identical replacement parts. This will ensure that the safety of the
appliance is maintained.
Additionally, please keep these instructions in a safe place for future
reference.
6
ELECTRICAL CONNECTIONS
DEVIL 6003 (3KW) HEATER UNIT
This model is provided with a 13 amp BS 1363 plug, fitted with a 13amp fuse and
MUST be connected to a standard, 230 Volt (50Hz) electrical supply, preferably
through an approved plug, or a suitably fused isolator switch.
WARNING: THIS APPLIANCE MUST BE EARTHED
IMPORTANT: The wires in the mains lead should be wired up in accordance
with the following colour code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
As the colours of the flexible cable of this appliance may not correspond with
the coloured markings identifying terminals in your plug, proceed as follows:
•
Connect the GREEN & YELLOW coloured cord to the plug
terminal marked with a letter E or Earth symbol “ ” or coloured
GREEN or GREEN & YELLOW.
• Connect the BROWN coloured cord to the plug terminal
marked a letter “L” or coloured RED.
•
Connect the BLUE coloured cord to the plug terminal marked
a letter “N” or coloured BLACK
If this appliance is found to be fitted with a plug which is moulded on to the
electric cable (i.e. non-rewireable) please note:
1. The plug must be thrown away if it is cut from the electric cable. There is a
danger of electric shock if it is subsequently inserted into a socket outlet.
2. Never use the plug without the fuse cover fitted.
3. Should you wish to replace a detachable fuse carrier, ensure that the
correct replacement is used (as indicated by marking or colour code).
4. Replacement fuse covers can be obtained from your local Clarke dealer
or most electrical stockists.
FUSE RATING
The fuse in the plug must be replaced with one of the same rating and this
replacement must be ASTA approved to BS1362.
We strongly recommend that this machine is connected to the mains supply
via a Residual Current Device (RCD).
E
7
DEVIL 6005 (5KW), DEVIL 6009(9KW) AND DEVIL 6015(15KW) UNITS
These machines MUST be connected to a 400 Volt, 3 PHASE 50Hz supply
through a suitably fused isolator switch. It cannot be operated from a single
phase supply.
The user should purchase a suitable connecting lead as shown in the diagram,
which is compatible with the appliance socket. The unit requires 5 pins includ-
ing a master earth pin, and is suitable for AC 380/415v, 50/60Hz with a capac-
ity of 16A/6h (Devil 6005 and 6009) or 32A/6h (Devil 6015) and rated at IP44
class or better insulation. A length of 2-3 metres is recommended as giving
mobility to the appliance but without becoming a trip hazard.
The plug incorporates a hood which will secure the cable in position when
engaged with the appliance.
If in any doubt, consult a qualified electrician. DO NOT attempt any electrical
repairs yourself.
8
OPERATION
The Devil range of fan assisted electric heaters are suitable for household
(Devil 6003 only) or workshop/factory use. They incorporate a thermostat
which detects the temperature of the room air and controls the heater to
maintain a pre-selected temperature between 0 & 40°C. A manually reset
thermal cutout is provided for safety in the event of overheating on the 6005,
6009 & 6015 models. The fan motor runs independently of the thermostat and
continues running after the heating element has been switched off.
With the heater suitably sited (ensure you comply with all safety precautions),
switch the heater ON to the chosen setting as follows:
3 KW HEATERS
The 3kw heater has 3 running speeds for the fan incorporating 2 settings for
both of the heating elements once the fan is set running. The other control is
a progressive thermostat which is rotated through 270 deg. A cutout is used
to maintain a constant pre-set temperature.
When using the heater to warm a cold room, first turn the thermostat to MAX
and run the heater on full power until the room temperature reaches the
required value, then turn the thermostat anti-clockwise until it switches off.
The thermostat will then switch the heater on and off automatically to control
the room temperature according to the pre-set value, maintaining a con-
stant room temperature. The 3kw unit is fitted with a self-resetting thermal
cutout.
3-position fan speed control thermostatic temperature control
9
When using the heater for the first time a slight emission of smoke may be
noticed. This is quite normal and soon stops. It is caused by residual traces of
oil remaining on the element from production.
After use, turn the thermostat to the OFF position and turn the selector switch
to the Fan Only position, and leave the unit to cool down for a couple of
minutes.
5KW, 9KW &15KW HEATERS
The 5 & 9kw units have a three position twist control for FAN only, and FAN plus
either half or full heat output. The 15kw unit has a four position control;- FAN
only, FAN + 1/3, FAN + 2/3 & FAN + full heat output. A thermostatic
temperature control is also provided for fine control of heat output at a
constant pre-set temperature.
Should the unit overheat, a thermal cutout will operate, shutting down the
unit. If this happens, allow a period of time for the unit to cool (approx. 10
minutes) before pressing the RESET using a suitable tool, and restarting the
unit.
When switching the unit OFF, it is strongly recommended that the unit is run in
the FAN ONLY mode for approx. 10 minutes, in order to cool the heating
elements, before switching OFF completely and finally disconnecting from
the mains supply.
The thermal cutout may also operate if the heater is shut down without
allowing to cool sufficiently. If, subsequently, the machine fails to start, press
the RESET using a suitable tool and try again.
Reset
Thermostatic temperature control
3-position fan speed / temperature control
10
MAINTENANCE
If the heater has been used, ALWAYS allow it to cool down for at least 10
minutes (by switching the heater OFF, but leave the fan running), then
disconnect from the mains supply before performing any maintenance tasks.
PERIODICALLY
• Disconnect from the mains supply, and use compressed air to clean
out the unit. ALWAYS wear a dust mask to perform this operation.
• If there is any serious build up of dirt, wipe thoroughly with a damp
cloth. Take care that no moisture enters the heater.
• Inspect the mains cable for damage. Heat damage will cause the
cable to stiffen and crack. If this is found, have the cable replaced.
Check cable routing and ensure it is well away from the heat
source.
• Ensure heating elements are clear of dust (use compressed air to
clean the heater if possible).
• Avoid using solvents when cleaning plastic parts, most plastics are
susceptible to damage from various types of commercial solvents.
• Refer to your CLARKE dealer if internal maintenance is required. The
unit is fitted with tamper-proof screws to discourage users from
dismantling the heater.
• When storing the heater, allow it to cool down, then cover it with its
plastic bag and place it in its packing box for storage in a dry,
ventilated place.
Autres manuels pour Devil 6003
1
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Clarke Chauffage
Clarke
Clarke XR60B Mode d’emploi
Clarke
Clarke DEVIL 371PC Manuel d'installation et d'exploitation
Clarke
Clarke DEVIL 371SPC Manuel d'installation et d'exploitation
Clarke
Clarke Devil 370P Manuel d'installation et d'exploitation
Clarke
Clarke DEVIL 4040 Mode d’emploi
Clarke
Clarke DEVIL 4003 Mode d’emploi
Clarke
Clarke BR13/250 Mode d’emploi
Clarke
Clarke XR60DV Mode d’emploi
Clarke
Clarke DEVIL 350B 230V Manuel d'installation et d'exploitation
Clarke
Clarke IQ2000 Manuel utilisateur
Clarke
Clarke OFR 5/50 Mode d’emploi
Clarke
Clarke DEVIL 2800PTC Mode d’emploi
Clarke
Clarke Devil 6003 Mode d’emploi
Clarke
Clarke DEVIL 2800PTC-B Mode d’emploi
Clarke
Clarke Devil IRD20B Mode d’emploi
Clarke
Clarke OFR13/250 Mode d’emploi
Clarke
Clarke Devil 370B Series Manuel d'installation et d'exploitation
Clarke
Clarke XR60 Manuel d'installation et d'exploitation
Clarke
Clarke DEVIL 9000PTC Mode d’emploi
Clarke
Clarke CONTRACTOR GRH30 Mode d’emploi
Manuels Chauffage populaires d'autres marques
oventrop
oventrop Regucor Series Manuel utilisateur
Blaze King
Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur
ELMEKO
ELMEKO ML 150 Manuel utilisateur
BN Thermic
BN Thermic 830T Manuel utilisateur
KING
KING K Series Mode d’emploi
Empire Comfort Systems
Empire Comfort Systems RH-50-5 Guide de démarrage rapide
