Clarke VE15C150 Mode d’emploi

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0715

VERTICAL AIR COMPRESSORS

MODEL NO: VE15C150, VE18C150, VE25C150

PART NO: 2226010, 2226020, 2226025

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Vertical Air Compressors.

Read this manual fully before use and follow the instructions carefully. In doing

so you will ensure the safety of yourself and those around you, and you can

look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal

facility.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

Before using your compressor it is in your own interest to read and pay attention

to the following safety rules.

1. Compressed air is dangerous. Do not point a jet of air at persons or animals, and do

not discharge compressed air against the skin.

2. DO NOT operate your compressor with the guard removed.

3. Repairs must only be carried out by a qualified engineer. If problems occur, contact

your Clarke dealer.

4. Before carrying out any maintenance, make sure that the pressure is released from

the air reservoir, and that the compressor is disconnected from the electrical supply.

5. DO NOT leave pressure in the receiver overnight, or when transporting.

6. DO NOT adjust, or tamper with the safety valves. The maximum pressure is factory

set, and clearly marked on the compressor.

7. DO NOT operate in wet or damp conditions. Keep the compressor dry at all times.

Similarly, clean air will allow the compressor to work efficiently. Do not use in dusty or

otherwise dirty locations.

8. Some of the metal parts can become quite hot during operation. Do not touch/

remove these until the compressor has cooled down.

9. Always set the pressure regulator to the recommended setting for the tool.

10. When spraying flammable materials e.g. cellulose paint, ensure that there is

sufficient airflow and keep clear of any source of ignition.

11. Before spraying any material always consult paint manufacturers instructions for

safety and usage.

12. Protect yourself. Goggles will protect your eyes from flying particles. A face mask will

protect you against paint spray and fumes.

13. Do not apply strain to electrical cables and make sure that air hoses are not kinked

or wrapped around the compressor.

14. When disconnecting air hoses or other equipment from your compressor, make sure

that the air supply is turned off at the outlet and vent all compressed air from within

the reservoir and other equipment attached to it.

15. Make sure that children and animals are kept well away from the compressor and

any equipment attached to it.

16. Make sure that all individuals using the compressor have had the necessary training

and have read and fully understand these operating instructions.

17. Make sure that any equipment or tool used in conjunction with your compressor, has

a safe working pressure exceeding that of the compressor.

18. Be very careful when transporting the compressor to prevent tipping over

19. Permanently installed systems must be installed by a competent engineer.

20. These compressors produce noise levels in excess of 70dB(A). Persons working near

the compressor must be supplied with ear protection.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY SYMBOLS

Read this instruction booklet carefully before positioning,

operating or adjusting the compressor.

Risk of electric shock. The compressor must be

disconnected from the mains supply before removing any

covers. Do not use in a damp environment.

Risk of accidental start-up. The compressor could start

automatically in the event of a power cut and subsequent

reset. Do not carry the compressor while it is connected to

the power source, or when the tank is filled with

compressed air.

This compressor contains surfaces which may reach a high

temperature during operation. Never operate with the

motor housing removed.

Wear safety goggles and ear protectors when using this

compressor

This compressor produces a high sound level during

operation. Ear protection should be worn.

ELECTRICAL CONNECTIONS

This machine MUST be connected to a 400 Volt, 3 phase 50Hz supply through a

suitably fused isolator switch. It cannot be operated from a single phase

supply.

A trailing socket is provided and should be wired as follows.

• Connect the GREEN or GREEN & YELLOW

coloured wire to the terminal marked with

the letter “E” or the Earth symbol “ “

• Connect the BLACK wire to the “N” or

Neutral terminal.

• Connect the remaining wires to the

termainals marked “L1”, “L2” and “L3”

Due to these high currents, the product must only be connected to a 3 phase

supply capable of supporting these loads (plus an acceptable degree of

headroom). This supply must be protected by a suitably rated circuit breaker

(or breakers) and isolator.

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical

repairs yourself.

WARNING: THE INSTALLATION OF THIS APPLIANCE SHOULD BE CARRIED

OUT BY A COMPETENT ELECTRICIAN AND BE IN ACCORDANCE WITH THE

CURRENT IEE WIRING REGULATIONS (BS7671-2:2008).

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

BEFORE USE

Before connecting your compressor to the power supply, check the following:-

• Push down the OFF button

• If fitted, remove the protective

plastic moulding from the top

of the cylinder head.

• Make sure that the supply

voltage matches the voltage

shown on the data label.

• Make sure that the compressor

is on firm level ground.

• This compressor must be

secured to the ground through the feet using suitable bolts and washers.

CHECK THE OIL LEVEL

1. Remove the dipstick from the oil

reservoir.

2. Ensure the oil level is between the

min and max marks on the

dipstick.

• Only use SAE30 compressor oil,

available from your Clarke

dealer Part No. 3050801

• Take care not to exceed the

maximum mark.

WARNING: TO PREVENT INJURY, ALWAYS GET ASSISTANCE WHEN LIFTING

OR MOVING THIS COMPRESSOR. ITS DESIGN MEANS IT IS TOP HEAVY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

If the compressor has not been used for more then 24 hours, open the drain

valve (on the bottom of the reservoir) and drain any condensate which has

collected. See page 10.

MOVING THE AIR COMPRESSOR

• Stop the compressor and disconnect it from the power supply

before you move it.

• Alway get help when moving the compressor.

• Do not lift by (or put strain on) valves or hoses.

CONNECTING AIR TOOLS

1. Attach the air hose to the outlet

valve.

2. Attach the air tool to the other

end of the air hose.

3. Turn the outlet valve tap to the On

position.

NOTE: The outlet valve is shown

without the air hose fitted for

clarity.

NOTE: To adjust the output pressure

we recommend that a

pressure regulator (not

supplied) be fitted between

the compressor and the tool.

WARNING: BEFORE CONNECTING AIR TOOLS, MAKE SURE THAT YOU

READ THE INSTRUCTIONS SUPPLIED WITH THE TOOL, ALSO ENSURE THAT

THE TOOL IS SUITABLE FOR USE WITH THE COMPRESSOR AND HOSE

SPECIFICATIONS.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

TURNING THE COMPRESSOR ON

1. Plug the compressor into the power supply.

2. Push down the ON button.

• The compressor will operate

until the reservoir is fully

pressurised. It will then shut

down.

• The compressor will start up

again when the pressure in the

reservoir decreases.

CHECK THE SAFETY VALVE

To make sure that the safety valve works correctly:-

1. Pull on the ring attached.

• Air will be released when you

pull on the ring and stop when

released.

2. If the valve does not operate in

this way, do not use the

compressor. The compressor must

be repaired by a qualified service

agent.

WARNING: DO NOT REMOVE OR TRY TO ADJUST THE SAFETY VALVE.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

REMOVING TOOLS FROM THE AIR HOSE

1. Push down the OFF button to stop

the compressor.

2. Turn the outlet valve handle to the

off position.

3. Operate the tool to depressurise

the air hose.

4. Disconnect the tool from the hose.

TURNING THE COMPRESSOR OFF

1. Follow steps 1-4 in “Removing Tools From The Air Hose” above.

2. Disconnect the compressor from the power supply.

3. Slowly open the outlet valve to depressurise the reservoir.

• You will hear a hissing sound as the reservoir depressurises.

4. Do not leave the compressor unattended if the reservoir is pressurised.

WARNING: ALWAYS SET THE PRESSURE REGULATOR TO ZERO BEFORE YOU

REMOVE OR REPLACE A TOOL.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

DRAINING THE RESERVOIR

1. Turn the compressor off and disconnect from the power supply.

2. Put a container below the drain

valve to collect the condensate.

• The drain valve is located on

the bottom of the reservoir

3. Open the drain valve slowly.

• Condensation will drain from

the reservoir.

4. Close the drain valve when the

reservoir has fully drained.

CAUTION: YOU MUST DRAIN THE RESERVOIR AFTER EACH DAYS USE AND

BEFORE YOU PUT YOUR COMPRESSOR INTO STORAGE.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Compresseur d'air

Clarke

Clarke CHAMP Manuel d'installation et d'exploitation

Clarke

Clarke SHHHAIR 50/9 Mode d’emploi

Clarke

Clarke RANGER 6/240 Mode d’emploi

Clarke

Clarke SHHHAIR 100/50 Mode d’emploi

Clarke

Clarke AIRMASTER 14/50P Mode d’emploi

Clarke

Clarke BANDIT Mode d’emploi

Clarke

Clarke RANGER 30 air Manuel d'installation et d'exploitation

Clarke

Clarke Warrior 55 Mode d’emploi

Clarke

Clarke RACER 9/50P Mode d’emploi

Clarke

Clarke SHHH 2 Manuel d'installation et d'exploitation

Clarke

Clarke XE10/100 Mode d’emploi

Clarke

Clarke SE Series Manuel d'installation et d'exploitation

Clarke

Clarke BOXER II 14/50P Mode d’emploi

Clarke

Clarke VE11C150 Mode d’emploi

Clarke

Clarke Raider 15/500 Mode d’emploi

Clarke

Clarke 6240056 Manuel d'installation et d'exploitation

Clarke

Clarke SHHHAIR MAX 50/350 Mode d’emploi

Clarke

Clarke CHAMP 3 Mode d’emploi

Clarke

Clarke SHHHAIR 30/9 Mode d’emploi

Clarke

Clarke CFP11F Manuel d'installation et d'exploitation

Clarke

Clarke RANGER 24 Mode d’emploi

Clarke

Clarke Ranger 7/240 Mode d’emploi

Clarke

Clarke Hunter 25 Mode d’emploi

Clarke

Clarke AIRMASTER 18/200 Mode d’emploi

Manuels Compresseur d'air populaires d'autres marques

Sparmax

Sparmax DC-25XR Manuel utilisateur

KAESER

KAESER M122 Manuel utilisateur

GMC

GMC GAC1500 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton Air Compressor Manuel utilisateur

Fini

Fini F3GST2TK Manuel utilisateur

Industrial Air

Industrial Air CP1580325 Manuel de programmation

Campbell Hausfeld

Campbell Hausfeld RP3300 Guide de démarrage rapide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuel utilisateur

Hitachi

Hitachi EC99S Manuel de l'opérateur

Parkside

Parkside PKO 270 A1 Manuel utilisateur

Sullair

Sullair 185 Manuel utilisateur

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuel utilisateur

Ferm

Ferm CRM1046 Manuel utilisateur

BE AC153 Manuel utilisateur

RIDGID

RIDGID OF25150A Manuel utilisateur

Johnson Controls

Johnson Controls QUANTUM LX Manuel

Sears

Sears Craftsman 919.167463 Manuel utilisateur

Ring Automotive

Ring Automotive RAC700 Manuel utilisateur