Clarke 2241000 Mode d’emploi

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0620 - ISS 2

ORIGINAL INSTRUCTIONS

AIR COMPRESSOR

MODEL NO: BANDIT

PART NO: 2241000

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE Air Compressor.

Read this manual fully before use and follow the instructions carefully. In doing

so you will ensure the safety of yourself and those around you, and you can

look forward to your purchase giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12

months from the date of purchase. Please keep your receipt which will be

required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or

tampered with in any way, or not used for the purpose for which it was

intended.

Faulty goods should be returned to their place of purchase, no product can

be returned to us without prior permission.

This guarantee does not effect your statutory rights.

PARTS AND SERVICING

For Parts & Servicing, please contact your nearest dealer, or

CLARKE International, on one of the following numbers.

PARTS & SERVICE TEL: 020 8988 7400

PARTS & SERVICE FAX: 020 8558 3622

or e-mail as follows:

PARTS: [email protected]

SERVICE: Service@clarkeinternational.com

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

Before using your compressor it is in your own interest to read and pay attention

to the following safety rules.

1. Compressed air is dangerous. Do not point a jet of air at persons or animals, and do

not discharge compressed air against the skin.

2. DO NOT operate your compressor with the guard removed.

3. Repairs must only be carried out by a qualified engineer. If problems occur, contact

your Clarke dealer.

4. Before carrying out any maintenance, make sure that the pressure is released from

the air reservoir, and that the compressor is disconnected from the electrical supply.

5. DO NOT leave pressure in the receiver overnight, or when transporting.

6. DO NOT adjust, or tamper with the safety valves. The maximum pressure is factory

set, and clearly marked on the compressor.

7. DO NOT operate in wet or damp conditions. Keep the compressor dry at all times.

Similarly, clean air will allow the compressor to work efficiently. Do not use in dusty or

otherwise dirty locations.

8. Some of the metal parts can become quite hot during operation. Do not to touch

these until the compressor has cooled down.

9. Always set the pressure regulator to the recommended setting for the tool.

10. When spraying flammable materials e.g. cellulose paint, ensure that there is

sufficient airflow and keep clear of any source of ignition.

11. Before spraying any material always consult paint manufacturers instructions for

safety and usage.

12. Protect yourself. Goggles will protect your eyes from flying particles. Face masks will

protect you against paint spray and fumes.

13. Do not apply strain to electrical cables and make sure that air hoses are not kinked

or wrapped around the compressor.

14. When disconnecting air hoses or other equipment from your compressor, make sure

that the air supply is turned off at the outlet and vent all pressurised air from within

the reservoir and other equipment attached to it.

15. Make sure that children and animals are kept well away from the compressor and

any equipment attached to it.

16. Make sure that all individuals using the compressor have had the necessary training

and have read and fully understand these operating instructions.

17. Make sure that any equipment or tool used in conjunction with your compressor, has

a safe working pressure exceeding that of the compressor.

18. Be careful when transporting the compressor to prevent tipping over

19. Permanently installed systems must be installed by a competent engineer.

20. These compressors produce noise levels in excess of 70dB(A). Persons working near

the compressor must be supplied with ear protection.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY SYMBOLS

Read this instruction booklet carefully before positioning,

operating or adjusting the compressor.

Risk of electric shock. The compressor must be

disconnected from the mains supply before removing any

covers. Do not use in a damp environment.

Risk of accidental start-up. The compressor could start

automatically in the event of a power cut and subsequent

reset. Do not carry the compressor while it is connected to

the power source, or when the tank is filled with

compressed air.

This compressor contains surfaces which may reach a high

temperature during operation. Never operate with the

motor housing removed.

Wear a safety goggles and ear protectors when using this

compressor

This compressor produces a high sound level during

operation. Ear protection should be worn.

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely, as

insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings

on the plug:

• The BLUE wire must be

connected to the

terminal which is

marked N or coloured

black.

• The BROWN wire must

be connected to the

terminal which is

marked L or coloured

red.

• The YELLOW AND

GREEN wire must be

connected to the terminal which is marked E or or coloured green.

We strongly recommend that this machine is connected to the mains supply

through a Residual Current Device (RCD)

If you are not sure, consult a qualified electrician. DO NOT try to do any

repairs.

WARNING! Read these electrical safety instructions thoroughly

before connecting the product to the mains supply.

WARNING! The wires in the power cable of this product are

coloured in accordance with the following code:

Blue = Neutral Brown = Live Yellow and Green = Earth

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

Earth

(Green and

a 13 Amp

the cable is firmly held by the clamp

fuse.

Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ASSEMBLY

FIT THE AIR FILTER

1. Remove the travel plug.

2. Screw the air filter into position.

• The air filter must be hand tight

only.

FIT THE OIL FILLER CAP

1. Remove the travel plug.

2. Insert the oil filler cap.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

MOVING THE AIR COMPRESSOR

• Stop the compressor and disconnect it from the power supply

before you move it.

• Always use the handle.

• To prevent damage, do not lift by (or put strain on) valves or hoses.

BEFORE USE

Before connecting your compressor to the power supply, check the following:-

• Set the ON/OFF switch to the

OFF position (pushed down).

• Make sure that the compressor

is on level ground.

• Make sure that the supply

voltage matches the voltage

shown on the data label.

CHECK THE OIL LEVEL

1. Make sure that the oil level is half

way up the oil sight glass.

2. If not, remove the oil cap and

add oil to the reservoir.

• Only use SAE30 compressor oil,

available from your Clarke

dealer Part No. 3050801

CAUTION: TO PREVENT INJURY, GET ASSISTANCE WHEN LIFTING THIS

COMPRESSOR.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OPERATION

If the compressor has not been used for more then 24 hours, open the drain

valve (on the bottom of the reservoir) and drain any condensate which has

collected. See page 10.

ATTACHING AIR TOOLS

1. Attach the air hose to the ¼" BSP

outlet valve.

2. Attach the tool to the end of the

air hose.

3. Turn the outlet valve handle to the

on position.

NOTE: The outlet valve is shown

without the air hose fitted for

clarity.

TURNING THE COMPRESSOR ON

1. Plug the compressor into the

power supply.

2. Lift the On/Off button.

• The compressor will operate

until the reservoir is fully

pressurised. It will then shut

down.

• The compressor will start up

again when the pressure in the

reservoir decreases.

WARNING: BEFORE CONNECTING AIR TOOLS, MAKE SURE THAT YOU

READ THE INSTRUCTIONS SUPPLIED WITH THE TOOL, ALSO ENSURE THAT

THE TOOL IS SUITABLE FOR USE WITH THE COMPRESSOR AND HOSE

SPECIFICATIONS.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SET THE OUTPUT PRESSURE

1. Use the pressure regulator to set

the output pressure.

• Turn clockwise to increase the

pressure.

• Turn counterclockwise to

decrease the pressure.

GAUGES

1. The reservoir pressure gauge

shows the current pressure in the

reservoir.

2. The outlet pressure gauge shows

the ‘user set’ outlet pressure. This

can be adjusted as shown above.

REMOVING TOOLS FROM THE AIR HOSE

1. Push down on the On/Off button

to stop the compressor.

WARNING: ALWAYS SET THE PRESSURE REGULATOR TO ZERO BEFORE YOU

REMOVE OR REPLACE A TOOL.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

2. Turn the outlet valve handle to the

off position.

3. Operate the tool to depressurise

the air hose.

4. Disconnect the tool from the hose.

TURNING THE COMPRESSOR OFF

1. Follow steps 1-3 in “Removing Tools From The Air Hose” above.

2. Disconnect the compressor from the power supply.

3. Slowly open the outlet valve to depressurise the reservoir.

• You will hear a hissing sound as the reservoir depressurises.

4. Do not leave the compressor unattended if the reservoir is pressurised.

DRAINING THE RESERVOIR

1. Turn the compressor off and

disconnect from the power

supply.

2. Put a container below the drain

valve to collect the condensate.

3. Open the drain valve slowly.

• Condensation will drain from

the reservoir.

4. Close the drain valve when the

reservoir has fully drained.

CAUTION: YOU MUST DRAIN THE RESERVOIR AFTER EACH DAYS USE AND

BEFORE YOU PUT YOUR COMPRESSOR INTO STORAGE.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Clarke Compresseur d'air

Clarke

Clarke REBEL 30 Manuel d'installation et d'exploitation

Clarke

Clarke VE11C150 Mode d’emploi

Clarke

Clarke RANGER 24 Mode d’emploi

Clarke

Clarke MONZA Mode d’emploi

Clarke

Clarke SHHHAIR 100/24 Mode d’emploi

Clarke

Clarke RACER 9/50P Mode d’emploi

Clarke

Clarke BOXER II 18/150 Mode d’emploi

Clarke

Clarke Pioneer 205 Manuel d'installation et d'exploitation

Clarke

Clarke Air SP15ND Manuel d'installation et d'exploitation

Clarke

Clarke RANGER 54 Mode d’emploi

Clarke

Clarke VE15C150 Mode d’emploi

Clarke

Clarke PIONEER 220 Manuel d'installation et d'exploitation

Clarke

Clarke MONZA Mode d’emploi

Clarke

Clarke SHHHAIR 50/9 Mode d’emploi

Clarke

Clarke XPPV11/50 Mode d’emploi

Clarke

Clarke BOXER 55 Manuel d'installation et d'exploitation

Clarke

Clarke CSC1000 Manuel

Clarke

Clarke Boxer 14/100P Mode d’emploi

Clarke

Clarke SE Ranges Manuel d'installation et d'exploitation

Clarke

Clarke BRONCO 2 OIL FREE Guide de dépannage

Clarke

Clarke CHAMP 265 Mode d’emploi

Clarke

Clarke SHHHAIR 100/50 Mode d’emploi

Clarke

Clarke CSS1 Mode d’emploi

Clarke

Clarke AIRMASTER 18/200 Mode d’emploi

Manuels Compresseur d'air populaires d'autres marques

Sparmax

Sparmax DC-25XR Manuel utilisateur

KAESER

KAESER M122 Manuel utilisateur

GMC

GMC GAC1500 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton Air Compressor Manuel utilisateur

Fini

Fini F3GST2TK Manuel utilisateur

Industrial Air

Industrial Air CP1580325 Manuel de programmation

Campbell Hausfeld

Campbell Hausfeld RP3300 Guide de démarrage rapide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuel utilisateur

Hitachi

Hitachi EC99S Manuel de l'opérateur

Parkside

Parkside PKO 270 A1 Manuel utilisateur

Sullair

Sullair 185 Manuel utilisateur

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuel utilisateur

Ferm

Ferm CRM1046 Manuel utilisateur

BE AC153 Manuel utilisateur

RIDGID

RIDGID OF25150A Manuel utilisateur

Johnson Controls

Johnson Controls QUANTUM LX Manuel

Sears

Sears Craftsman 919.167463 Manuel utilisateur

Ring Automotive

Ring Automotive RAC700 Manuel utilisateur