Cisco WAP371 Manuel utilisateur

Autres manuels pour WAP371

3

Table des matières

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco Aironet 1300 Series Manuel utilisateur

Cisco

Cisco Catalyst Wireless 9163E Manuel utilisateur

Cisco

Cisco Aironet 1250 Series Manuel utilisateur

Cisco

Cisco WAP571 Manuel utilisateur

Cisco

Cisco WAP121 Manuel utilisateur

Cisco

Cisco 800 Series Manuel utilisateur

Cisco

Cisco Meraki MR36H Manuel utilisateur

Cisco

Cisco Small Business AP541N Manuel utilisateur

Cisco

Cisco aironet 1524SB Instructions d'installation et d'utilisation

Cisco

Cisco Catalyst Wireless 9164I Series Manuel utilisateur

Cisco

Cisco Aironet 1240AG Series Manuel

Cisco

Cisco WAP2000 Manuel utilisateur

Cisco

Cisco MR18 Manuel utilisateur

Cisco

Cisco AIR-AP1232AG-A-K9 - Aironet 1230AG - Wireless Access... Manuel utilisateur

Cisco

Cisco 1004-CH - 1004 Enet/ISDN/Bri Rter Guide de référence rapide

Cisco

Cisco Aironet 1600 Series Guide de référence rapide

Cisco

Cisco Linksys Wireless-G WBP54GV2 Manuel utilisateur

Cisco

Cisco Meraki MR76 Manuel utilisateur

Cisco

Cisco MERAKI MR34 Manuel utilisateur

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manuel

Cisco

Cisco Aironet 1100 Series Manuel de l'opérateur

Cisco

Cisco AP541N-A-K9 Mode d’emploi

Cisco

Cisco Aironet 1140 Series Manuel utilisateur

Cisco

Cisco NCS 4201 Mode d’emploi

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

Reboot and Reset Factory Default Settings on

the WAP371

Objective

The factory default reset erases all configuration settings that have been modified by the

user, and restores the device to its original settings. This may be helpful if you lose the

password to a device and wish to regain access.

Note: It is advised to save a backup copy of the configuration before beginning this process.

Refer to Download/Backup Configuration on the WAP 371 for additional information.

Performing a reboot restarts the device with a saved configuration.

The objective of this article is to show you how to reset to factory default settings and how to

reboot a WAP371 Wireless Access Point.

Applicable Devices

• WAP371

Software Version

• 1.0.1.5

Reset to Factory Default

There are two ways to reset the Access Point to the factory default configuration:

• Hardware reset

• Reset with the use of the web configuration utility

Hardware Reset

Step 1. Press the Reset button for approximately ten seconds with a pin located at the back

of the device.

The Access Point reloads and is set to the default configuration settings.

Step 2. Login with the default credentials. The default username is cisco, and the default

password is cisco.

Reset with the use of the Web Configuration Utility

Step 1. Log in into the web configuration utility page and choose Administration > Reboot.

The Reboot page opens:

Step 2. To reset the device, click the Reboot To Factory Default button.

A Confirm page appears:

Step 3. Click OK.

A Progress Bar appears:

Step 4. After the reboot is completed, login with the default credentials. The default

username is cisco, and the default password is cisco.

Rebooting the Device

There are two ways to reboot the Access Point:

• Hardware reboot

• Reboot with the use of the web configuration utility

Hardware Reboot

Step 1. Press the power button to turn off the device. After 10 seconds have passed, press

the power button a second time to power the device back on.

The Access Point reboots and is refreshed.

Reboot with the use of the Web-based utility

Step 1. Log in to the web configuration utility page and choose Administration > Reboot.

The Reboot page opens:

Step 2. To reboot the device, click the Reboot button.

A Confirm page appears:

Step 3. Click OK to continue with reboot.

A Progress Bar appears:

Step 4. The Login Page appears. Login with the saved administration credentials.