Cisco WAP121 Manuel utilisateur

Autres manuels pour WAP121

9

Ce manuel convient aux modèles suivants

13

Table des matières

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco Aironet Wave 2 Manuel d'installation

Cisco

Cisco WAP150 Manuel utilisateur

Cisco

Cisco WET200 Wireless-G Business Ethernet Bridge Manuel utilisateur

Cisco

Cisco ASR 1001 Manuel

Cisco

Cisco WAP131 Manuel utilisateur

Cisco

Cisco WAP371 Mode d’emploi

Cisco

Cisco Aironet 3600 Series Manuel utilisateur

Cisco

Cisco AIR-AP1020 - 1000 Series Lightweight Access... Manuel utilisateur

Cisco

Cisco AIR-AP1572IC Manuel

Cisco

Cisco AIR-AP1131G-A-K9 Manuel utilisateur

Cisco

Cisco 1830 Series Manuel utilisateur

Cisco

Cisco Meraki MR52 Manuel

Cisco

Cisco aironet 2800 series Guide de référence rapide

Cisco

Cisco Aironet 1815T Manuel utilisateur

Cisco

Cisco WAP351 Manuel utilisateur

Cisco

Cisco Aironet 1815i Manuel utilisateur

Cisco

Cisco WAP121 Manuel utilisateur

Cisco

Cisco Wap581 Manuel utilisateur

Cisco

Cisco Meraki MR45 Manuel utilisateur

Cisco

Cisco WAP121 Mode d’emploi

Cisco

Cisco Catalyst 9130AX Series Manuel utilisateur

Cisco

Cisco Aironet 1520 Series Manuel

Cisco

Cisco Aironet 1300 Series Manuel utilisateur

Cisco

Cisco 500 Series Manuel de l'opérateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

●

●

●

●

●

●

●

●

●

●

●

●

Reboot and Reset the Wireless Access Point

to Factory Default Settings

Objective

Rebooting or restarting the Wireless Access Point (WAP) deletes the logs stored in the

volatile memory. This process is performed when certain changes in the settings need a

reboot or if the WAP is not responding or booting up properly. Resetting the WAP to factory

default settings, on the other hand, erases all configurations that have been set by the user,

and restores the device to its original settings. A reset is recommended if most of the WAP

settings need to be reconfigured.

This article aims to show you how to reboot and reset your WAP to factory default settings.

Applicable Devices

WAP100 Series

WAP300 Series

WAP500 Series

Software Version

1.0.6.5 - WAP121, WAP321

1.0.2.8 - WAP131, WAP351

1.0.1.7 - WAP150, WAP361

1.3.0.3 - WAP371

1.2.1.3 - WAP551, WAP561

1.0.0.17 - WAP571, WAP571E

Reboot the Wireless Access Point

There are two ways to reboot the WAP:

Hardware reboot

Reboot through the web-based utility

Note: Images may vary depending on the exact model of your WAP. The images below are

taken from the WAP321.

Hardware Reboot

You have two ways to reboot the device hardware:

Turn the device off by pressing the POWER button while the device is connected to the

power outlet.

Note: The POWER button only works if the device is using a power adapter. If power is

supplied through Power over Ethernet (PoE), unplug your Ethernet connection for three

●

seconds then plug it back.

Press the Reset button for about three seconds only, or until the lights go off.

Reboot through the Web-based Utility

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Click the Reboot button.

Step 3. Click OK in the confirmation window.

●

●

You should now have rebooted your device.

Reset to Factory Default Settings

There are two ways to reset the WAP to factory default settings:

Hardware reset

Reset through the web-based utility

Hardware Reset

Step 1. Press the Reset button for more than 10 seconds until the lights go off.

Step 2. Release the Reset button when the lights turn back on.

Reset through the Web-based Utility

Step 1. Log in to the web-based utility of your WAP and choose Administration > Reboot.

Step 2. Click the Reboot To Factory Default button.

Step 3. Click OK in the confirmation window.

You should now have reset your device to factory default settings.