Cisco Meraki MR12 Manuel utilisateur

Assigning Static IP Addresses to an MR12 or MR58

The MR12 and MR58 wireless access points have two Ethernet ports that can be used to connect the device to a wired network. However, a static IP can only

be set on the primary Ethernet interface.

This article will discuss:

• Identifying the primary Ethernet port

• Behavior differences between primary and secondary ports

• Determining which port is being used

•Assigning a static IP

Identifying the Primary Ethernet Port

MR12

The primary Ethernet port is directly adjacent to the power connector and is labeled as Uplink.

MR58

The primary Ethernet port is located on the bottom-left side of the AP and is labeled as ETH0.

Behavior differences between primary and secondary ports

Primary (Ethernet 0)

This interface is capable of receiving power using PoE and can be assigned a static IP address. It is also capable of 10/100/1000Mbps speeds. It is intended for

connecting the MR12 to the rest of the network.

Secondary (Ethernet 1)

This interface can only receive an IP from DHCP and is not able to receive power using PoE. It is only capable of 10/100 speeds. It is still able to connect to the

Meraki Cloud Controller if the Primary connection is down, but is intended for used by a wired client. To allow use by a wired client, please refer to our

documentation regarding Extending the LAN with a Wireless Mesh Link.

Determining which port is being used

The simplest way to determine which port is being used is to physically look at the device, and refer to the diagrams above. If you are not near the device, the

easiest way to determine if the secondary port is being used is by looking at the AP Dashboard. Navigate to Monitor > Access points and click the AP in

question. Look under Status for LAN IP #. If the # = 1, then the AP is connected using the primary port. If # = 2, then the AP is connected using its secondary

port.

Assigning a static IP

A static IP can be assigned to the AP's primary interface in two ways.

Dashboard

1. In Dashboard, go to Monitor > Access points and select the AP in question.

2. Click the Edit icon.

3. On the page that appears, next to IP type select Static IP.

4. Enter the appropriate settings and click Save.

Local web interface

Refer to the MR Quick Start Guide for instructions on how to set the IP address using the local web interface.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco Meraki Go GR62 Manuel utilisateur

Cisco

Cisco Aironet 1600 Series Manuel utilisateur

Cisco

Cisco Meraki Go GR12 Manuel utilisateur

Cisco

Cisco 1232AG - Aironet - Wireless Access Point Manuel

Cisco

Cisco FM PONTE-50 Manuel

Cisco

Cisco WAP125 Manuel utilisateur

Cisco

Cisco AIR-LAP1142N-A-K9 Manuel utilisateur

Cisco

Cisco Aironet 1400 Series Manuel utilisateur

Cisco

Cisco Aironet 1520 Series Manuel utilisateur

Cisco

Cisco Aironet 3700 Series Guide de référence rapide

Cisco

Cisco Linksys WAP54GX Manuel utilisateur

Cisco

Cisco Small Business WAP551 Mode d’emploi

Cisco

Cisco Catalyst IW6300 Series Manuel

Cisco

Cisco WAP121 Manuel utilisateur

Cisco

Cisco aironet 2800 series Guide de référence rapide

Cisco

Cisco AIR-AP1131G-A-K9 Manuel utilisateur

Cisco

Cisco AIR-CAP1552H-x-K9 Manuel utilisateur

Cisco

Cisco Meraki CW91661-MR Manuel

Cisco

Cisco WAP121 Manuel utilisateur

Cisco

Cisco Aironet OfficeExtend AIR-OEAP602I-E-K9 Manuel utilisateur

Cisco

Cisco NCS 4201 Mode d’emploi

Cisco

Cisco Small Business AP541N Mode d’emploi

Cisco

Cisco WAP371 Manuel utilisateur

Cisco

Cisco WAP571E Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur