Cisco WAP121 Manuel utilisateur

Autres manuels pour WAP121

9

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco Aironet 521 Manuel utilisateur

Cisco

Cisco WAP371 Manuel utilisateur

Cisco

Cisco Aironet 1815T Manuel utilisateur

Cisco

Cisco WAP150 Manuel utilisateur

Cisco

Cisco WAP371 Manuel utilisateur

Cisco

Cisco 1232AG - Aironet - Wireless Access Point Manuel

Cisco

Cisco AIR-AP352E2R - Aironet 350 - Wireless Access... Manuel utilisateur

Cisco

Cisco FM PONTE-50 Manuel

Cisco

Cisco MERAKI MR66 Manuel utilisateur

Cisco

Cisco Small Business WAP551 Manuel utilisateur

Cisco

Cisco WAP125 Manuel utilisateur

Cisco

Cisco Small Business WAP551 Mode d’emploi

Cisco

Cisco Aironet 1530 Series, 1532 Manuel utilisateur

Cisco

Cisco CW91641-A Manuel

Cisco

Cisco Aironet 1250 Series Manuel utilisateur

Cisco

Cisco Aironet 1530 Manuel utilisateur

Cisco

Cisco Catalyst IW9167E Manuel

Cisco

Cisco GR10-HW Manuel utilisateur

Cisco

Cisco Meraki MR53E Manuel utilisateur

Cisco

Cisco Aironet 2800I Series Manuel utilisateur

Cisco

Cisco Meraki MR42E Manuel utilisateur

Cisco

Cisco AIR-AP1572IC Manuel

Cisco

Cisco Catalyst IW9165E Manuel utilisateur

Cisco

Cisco Meraki MR20-HW Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

Reboot and Factory Default Reset on

WAP121 and WAP321 Access Points

Objective

This article explains how to perform a standard reboot and also how to reset to factory

default on the WAP121 and WAP321 access points. Reboot or restart of the network

device is made when certain changes in the settings need a reboot or if the device is

frozen. Consequences of reboot will result in the deletion of logs in volatile memory.

The configuration settings of the network device gets reflected after the restart. Factory

default reset is used to remove the running/current configuration settings on the

network device and to restore it to the original default settings. Factory default reset is

recommended when the whole device needed to be reconfigured and also in case if

you forget the password and not able to recover by any means such as telnet.

Applicable Devices | Firmware Version

WAP121 | 1.0.3.4 (Download latest)

●

WAP321 | 1.0.3.4 (Download latest)

●

Reset to Factory Default

There are two ways to reset to factory default settings to the factory default

configuration:

Hardware Reset

●

Factory default reset by web configuration utility

●

Hardware Reset

Step 1. Hold the Reset button located at the back of the device for approximately ten

seconds with a pin.

The Access Point reloads and is set to the default configuration settings.

Step 2. Launch a web browser, such as Internet Explorer or Mozilla Firefox. Type the

default static IP address 192.168.1.245 in the URL bar and press enter. To reach that

IP address, be sure that your computer is on the 192.168.1.xxx network.

If your network has a DHCP server, then the factory default IP address configuration of the

WAP is DHCP. In the absence of a DHCP server, the access point will fallback to the

default static IP address after 60 seconds.

Step 3. Login with the default credentials.The default username is cisco, and the

default password is cisco.

Factory Default Reset by Web Configuration Utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot.

The Reboot page opens:

Step 2. Click Reboot To Factory Default to reboot the access point and return the

device to factory default settings. Once rebooted to factory default, all saved

configurations will be lost.

Step 3. The Confirm window appears. Click OK to continue with the reboot to factory

default settings.

Reboot Access Point

There are two ways to reset the Access Point:

• Hardware reset

• Reset with the use of the web configuration utility

Reboot Access Point by Hardware

Step 1. Press the power button to turn off the device. After 10 seconds have passed,

press the power button a second time to power the device back on.

The Access Point reboots and is refreshed.

Reboot Access Point by Web Configuration Utility

Step 1. Log in to the web configuration utility and choose Administration > Reboot.

The Reboot page opens:

Step 2. Click Reboot to reboot the device.

Step 3. The confirm window appears. Click OK to continue with the reboot of the

device.

If you would like to read an article on this same topic, check out Reboot and Reset the

Wireless Access Point to Factory Default Settings.