Cisco Aironet 1570 Series Mode d’emploi

CHAPTER

3-1

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Mounting the Access Point

This chapter describes how to install the 1572 access point and contains the following sections:

•Unpacking the Access Point, page 3-2

•Tools and Hardware Common For All Mounting Options, page 3-3

•Choosing the Mounting Kit, page 3-5

•Strand Mount Kit 1, page 3-7

•Strand Mount Kit 2, page 3-9

•Strand Mount Kit 3, page 3-14

•Pole Mount Kit 1, page 3-19

•Pole Mount Kit 2, page 3-23

•Pole Mount Kit 3, page 3-41

3-2

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Unpacking the Access Point

To unpack the access point, follow these steps:

Step 1 Open the shipping container and carefully remove the contents.

Step 2 Return all packing materials to the shipping container, and save it.

Step 3 Ensure that all items listed in the following sections are included in the shipment. If any item is damaged

or missing, notify your authorized Cisco sales representative.

AP1572IC Package Contents

•One AP1572IC series access point

•Grounding Lug kit containing #6 AWG grounding wire with grounding lug (having two holes), and

two M4.0 x 10mm screws

•Oxide inhibitor paste

•Cisco product documentation pointer card

AP1572EC Package Contents

•One AP1572EC series access point

•Grounding Lug kit containing #6 AWG grounding wire with grounding lug (having two holes), and

two M4.0 x 10mm screws

•Two M5.0 x 10mm screws

•Four 10 inch environmental seal tape

•Oxide inhibitor paste

•One PG13.5 cable gland

•Cisco product documentation pointer card

AP1572EAC Package Contents

•One AP1572EAC series access point

•Grounding Lug kit containing #6 AWG grounding wire with grounding lug (having two holes), and

two M4.0 x 10mm screws

•Four 10 inch environmental seal tape

•Oxide inhibitor paste

•Two PG13.5 cable glands

•DC Connector (Cisco Part Number 29-100226-01)

3-3

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Optional AP Hardware

•Cisco product documentation pointer card

Optional AP Hardware

Depending on your requirements, you can order the following optional equipment from Cisco as part of

your shipment:

•Strand mounts kits

•Pole mount kits

•External antennas

•GPS antenna

Tools and Hardware Common For All Mounting Options

The tools and hardware required for each mounting option, is listed in the corresponding sections. The

following tools and materials are required during various stages of installing the AP, for all mounting

options:

•10 mm open end or box wrench, for M6 bolts

•13 mm box-end wrench or socket set, for M8 bolts

•Adjustable wrench with opening up to 33 mm and 28 mm socket.

•0.5 inch or 13 mm wrench (for port plugs)

•Ground lug crimping tool (Panduit CT-720 with CD-720-1 die)

•6-AWG copper ground wire

•Small flat-screwdriver for DC power connector

•Optional shielded outdoor-rated Ethernet (CAT5e or better) cable with 0.20 to 0.35 in

(0.51 to 0.89 cm) diameter

•Optional Ethernet RJ-45 connector and installation tool

•Optional shielded outdoor-rated DC power cable with 0.20 to 0.35 inch (.0.51 to 0.89 cm) diameter,

rated at 10 amp, 10-16 V DC cable.

•Optional ground rod, as required by local regulations

•Optional ladder, power lift, rope, or other tools as required

•5/16" socket wrench (alternative to M8 bolts) for PMK1 mount clamp

•Installation tool for the steel band straps (AIR-BAND-INST-TL=) for fastening the strap brackets

when using PMK2 and PMK3.

3-4

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Typical Access Point Installation Components

The access point is designed to be installed in an outdoor environment, such as on exterior walls, off

cable strands, and on vertical and horizontal poles, such as streetlight poles. Carefully review Figure 3-1

to become familiar with the system components, connectors, indicators, cables, system interconnection,

and grounding.

Note The illustrations in this document show all available connections for the access point. Unused

connections are capped with a connector plug to ensure the watertight integrity of the access point,

except for the AC power entry connector on the in AP1572EAC version access point. Liquid-tight

adapters are provided for connector openings, which can be installed before or after deploying the access

point.

When not using the AC input connector to power the in AP1572EAC version (for example when

powering using the Cisco power injector), it is important to cover the AC power entry connector. The

correct cap is Remke part number 75-0086 (http://www.remke.com/). This cap is included with the

AIR-PWRINJ1500-2= power injector. If you are using PoE directly from a switch or powering via DC,

then you will need to order AIR-ACC15-AC-CAP=.

Figure 3-1 Components in a Typical Access Point Installation

352933

10 8

3-5

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Choosing the Mounting Kit

Note The access point is designed with consideration for resistance to effects of lightning effects on the access

point electronics. The access point employs lightning arrestor circuitry on the Ethernet and power ports.

On the input Ethernet port, Gas Discharge Tubes (GDT) are used for the Power Entry Module (PEM) to

mitigate lightning effect. On the AC power, GDTs are also used along with fuses to mitigate high-current

condition. For the DC power, a fuse is used to mitigate high current condition.

While not a common practice, the user may want to consider using lightning protection at the antenna

ports for added protection. To meet EN/IEC60950-22 (Clause 4.2) requirements, the installer must

ensure that additional protection is provided external to this equipment to reduce transient surges from

Overvoltage IV to Overvoltage Category II at the AC power input of the access point. The over-voltage

and fault-current protection components used to achieve this protection must comply with the IEC 61643

series of standards. To meet CAN/CSA-C22.2 No. 60950-22-07/UL60950-22 requirements, the installer

may use alternative components to provide this additional protection. Those components may comply

with ANSI/IEEE C62.11, CSA Certification Notice No. 516, CSA C22.2 No. 1, or UL 1449. Suitability

of the components for the application must be determined for the intended installation. (For example,

some devices are suitable for installation on the load side of the service entrance only, and some are

suitable for use with cord-connected equipment only.)

Choosing the Mounting Kit

Personnel installing the access point must understand wireless access points and bridging techniques and

grounding methods.

Note • When mounting an access point horizontally or vertically, ensure that the base of the access point,

with the LED indicators, is visible from the ground below the access point.

•Ensure that the access point is mounted in such a way so that all antenna ports and the console port

are accessible for future use.

1Pole or wall on which AP is vertically

mounted.

6Ground

2Shielded outdoor-rated Ethernet

(CAT5e or better) cable1

1. User supplied.

7AC power cord2

2. The safety ground wire in the AC power cord must have a ground path to a grounding rod.

3Water drip loop 8Power injector3

3. The shielded Ethernet cable has a ground path through the power injector and the safety ground wire in the AC power cord.

46-AWG copper grounding wire19Shielded Ethernet (CAT5e or better) cable1

5Ground rod110 Controller (through a switch)

3-6

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Choosing the Mounting Kit

Depending on the particular AP version, the 1570 Series Access Point can be strand, wall, or pole

mounted. From the following tables, choose a mounting kit for you access point version based on your

mounting scenario.

Table 3-1 Mounting Kits for AP1572IC

AP Orientation AP1572IC is always mounted in a horizontal orientation.

Kit for Strand Mount without Cable Bundle Strand Mount Kit 1 [AIR-ACCSMK1570-1]

Kits for Strand Mount with Cable Bundle Strand Mount Kit 2 [AIR-ACCSMK1570-2]

Strand Mount Kit 3 [AIR-ACCSMK1570-3]

Kit for Wall, Vertical Pole, Horizontal Pole and

Off-Angle Pole

Pole Mount Kit 3 [AIR-ACCPMK1570-3=]

Table 3-2 Mounting Kits for AP1572EC

AP Orientation AP1572EC can be mounted in horizontal and vertical

orientations. However, Strand Mount Kit 1 is not supported.

Kits for Strand Mount with Cable Bundle Strand Mount Kit 2 [AIR-ACCSMK1570-2]

Strand Mount Kit 3 [AIR-ACCSMK1570-3]

Kit for Vertical Pole Pole Mount Kit 1 [AIR-ACCPMK1570-1]

(poles of diameter 2 to 6 inches)

Pole Mount Kit 2 [AIR-ACCPMK1570-2=]

(poles of diameter 2 to 16 inches)

Kit for Wall, Horizontal Pole, and Off-Angle Pole Pole Mount Kit 2 [AIR-ACCPMK1570-2=]

Kit for Wall, Vertical Pole, Horizontal Pole and

Off-Angle Pole

Pole Mount Kit 3 [AIR-ACCPMK1570-3=]

Table 3-3 Mounting Kits for AP1572EAC

AP Orientation AP1572EAC is always mounted in a vertical orientation. It is

not mounted on cable strands.

Kit for Vertical Pole Pole Mount Kit 1 [AIR-ACCPMK1570-1]

(poles of diameter 2 to 6 inches)

Pole Mount Kit 2 [AIR-ACCPMK1570-2=]

(poles of diameter 2 to 16 inches)

Kit for Wall, Horizontal Pole, and Off-Angle Pole Pole Mount Kit 2 [AIR-ACCPMK1570-2=]

3-7

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Strand Mount Kit 1

The Strand Mount Kit 1 (abbreviated as SMK1) is for mounting the AP directly to a cable strand, when

there is no cable bundle. SMK1 consists of two single-piece clamps, which clamp the cable strand across

the back of the access point. As the cable strand runs directly across the back surface of the AP, there is

no space left between the back surface of the AP and the cable strand.

For instructions on mounting an AP using SMK1, see Strand Mounting Using SMK1, page 3-7.

Strand Mounting Using SMK1

When mounting the access point on a cable strand where you don’t have to accommodate a cable bundle,

you can use the SMK1 strand mount kit.

Note The access point must be installed on a cable strand by a professional cable installer.

Table 3-1 lists the materials you need to strand mount the AP using SMK1.

Table 3-1 Materials Needed to Mount the AP using SMK1

To mount the access point, follow these steps:

Step 1 Hold the AP’s back surface up against the support cable, and ensure that the cable runs through one of

the three sets of cable grooves.

When installing external antennas, which are mounted on the AP using an additional antenna bracket,

the AP may tilt to one side due to the uneven weight distribution. To counteract this tilt, three sets of

cable grooves are provided on the back surface of the AP. This allows you to run the cable through

different sets of the grooves so as to adjust the cable’s position against the AP’s back surface, and thereby

counter the tilt.

Material Needed In Kit?

SMK1 strand mount kit Yes

Four M8 x16mm button-head bolts, and its washers Yes

5 mm hex wrench No

3-8

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Strand Mount Kit 1

Figure 3-2 AP Back Surface with Cable Strand in Cable Grooves

Step 2 Clamp the cable using the SMK1 cable clamps. Secure each clamp with two M8 x16mm bolts (with lock

washers) on the back surface of the access point (see Figure 3-2). Hand-tighten the bolts to 13 to 15 ft.lbf

(17.6 to 20.3 Nm).

Note The strand support cable and the SMK1 kit together provide the grounding for the access point.

1Cable Strand/Support Cable running

though center cable grooves.

2Screw holes for the M8 x16mm button-head

bolts, to fasten the SMK1 cable clamp to the

AP.

3SMK1 cable clamp, already installed,

with supporting cable running through

center groove.

4Two M8 x16mm button-head bolts used to

fasten each SMK1 cable clamp.

353257

3-9

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Strand Mount Kit 2

Step 3 Continue with installing antennas, connecting the data cables, grounding the access point, and powering

the access point. For information on these, see Chapter 4, “Installing Other Components.”

Strand Mount Kit 2

The Strand Mount Kit 2 (abbreviated as SMK2) can accommodate a 1.75 inch cable bundle between the

support cable strand and the back surface of the AP. The SMK2 allows a distance of 2.42 inches from

the back surface of the AP to the center of the cable strand (see Figure 3-4).

The SMK2 consists of these parts:

•Strand mount cable brackets (see Figure 3-5)

•Cable clamps (see Figure 3-5)

•5/16"-18 bolt for fastening the cable clamps to the strand mount cable bracket (see Figure 3-5)

For instructions on mounting an AP using SMK2, see Strand Mounting Using SMK2, page 3-10.

Figure 3-3 SMK2 Cable Clamps and Cable Bracket Assembly Dimensions in inches [and millimeters]

353374

88.4

3.48

103.2

4.06

61.572

2.42

63.5

2.50

3-10

Cisco Aironet 1570 Series Outdoor Access Point Hardware Installation Guide

OL-32138-01

Chapter 3 Mounting the Access Point

Strand Mount Kit 2

Figure 3-4 AP Mounted Using SMK2 - Dimensions in inches [and millimeters]

Strand Mounting Using SMK2

When mounting the access point on a cable strand where you need to accommodate a cable bundle also,

you must use SMK2 strand mount kit.

Note The access point must be installed on a cable strand by a professional cable installer.

Table 3-2 lists the materials you need to strand mount the AP using SMK2.

Table 3-2 Materials Needed to Mount the AP using SMK2

To mount the access point, follow these steps:

61.6

353703

2.42

200.7

7.90

Material Needed In Kit?

SMK2 strand mount kit Yes

Four M8 x16mm button-head bolts, and its washers Yes

5 mm hex wrench No

13 mm box-end wrench No

Autres manuels pour Aironet 1570 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Point d'accès sans fil

Cisco

Cisco GR10-HW Manuel utilisateur

Cisco

Cisco 1130AG - Aironet - Wireless Access Point Manuel utilisateur

Cisco

Cisco WAP150 Manuel utilisateur

Cisco

Cisco Linksys WAP54G LA Manuel utilisateur

Cisco

Cisco Aironet 1400 Series Manuel utilisateur

Cisco

Cisco MERAKI MR72 Manuel utilisateur

Cisco

Cisco Small Business WAP44 Mode d’emploi

Cisco

Cisco WAP121 Mode d’emploi

Cisco

Cisco AT&T U-VERSE VEN401 Manuel utilisateur

Cisco

Cisco AIR-AP1010 - 1000 Series Lightweight Access... Manuel utilisateur

Cisco

Cisco Wap581 Manuel utilisateur

Cisco

Cisco Catalyst IW9167I Manuel

Cisco

Cisco Meraki Go GR10 Manuel utilisateur

Cisco

Cisco WAP121 Manuel utilisateur

Cisco

Cisco Catalyst 9130 Manuel utilisateur

Cisco

Cisco Aironet 521 Manuel utilisateur

Cisco

Cisco Meraki MR70 Manuel utilisateur

Cisco

Cisco Aironet 700W Series Manuel utilisateur

Cisco

Cisco Meraki MR55 Manuel utilisateur

Cisco

Cisco Meraki MR36 Manuel utilisateur

Cisco

Cisco WAP131 Manuel utilisateur

Cisco

Cisco Meraki GR60 Manuel utilisateur

Cisco

Cisco Catalyst Wireless 9163E Manuel utilisateur

Cisco

Cisco AIR-AP1020 - 1000 Series Lightweight Access... Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur