Cisco NCS 5700 Manuel utilisateur

Install the Chassis

Before you begin this task, ensure that you have read and understood the safety warnings in the Standard

Warning Statements section of the Safety Warnings handout topic.

Installing the Cisco NCS 5700 router involves these tasks:

The images in this chapter are only for representation purposes, unless specified otherwise. The chassis' actual

appearance and size may vary.

Note

•Rack Types, on page 1

•Rack Mount the Chassis, on page 2

•Ground the Chassis, on page 35

•Connect AC Power to the Chassis, on page 37

•Connect DC Power to the Chassis , on page 40

•Power Supply Unit Input and Output Ranges, on page 43

Rack Types

Figure 1: Rack specification EIA (19 inches and 23 inches)

Install the Chassis

Table 1: Rack specification EIA (19 inches and 23 inches)

Mounting Flange

Dimension (Z)

Rack Mounting Hole

Centre-Centre (Y)

Rack Front Opening

(X)

Rack TypePost Type

482.6mm (19”)465mm (18.312”)450.8mm (17.75”)19 inches (48.3

centimeters)

4 Post

2 Post

584.2mm (23”)566.7mm (22.312”)552.45mm (21.75”)23 inches (58.4

centimeters)

4 Post

2 Post

Rack mount kit contains the rack mounting brackets for 19 inch rack. To install the chassis in a 23-inch rack

or an ETSI rack, you need adapter plates to accommodate the 19 inch rack mount brackets. The adapter plates

for installing in a 23-inch rack or an ETSI rack are included in the accessory kit for the NCS-57C3-MOD

chassis.

Note

The NCS-57C1 router can be installed either on the 19-inch rack or 23-inch rack. To install this router on the

23-inch rack, you must mount the extension brackets on the 23-inch rack post.

Note

Rack Mount the Chassis

The chassis can be mounted on a 2-post or a 4-post rack.

•Rack Mount the NCS-57B1 Chassis in a 2-Post Rack, on page 3 — Contains the procedure for mounting

the NCS-57B1-6D24-SYS and NCS-57B1-5DSE-SYS chassis in a 2-post rack.

•Rack Mount the NCS-57C1 Chassis in a 2-Post Rack with Sliders, on page 5 — Contains the procedure

for mounting the NCS-57C1 chassis in a 2-post rack.

•Rack Mount the NCS-57C3-MOD Chassis in a 2-Post Rack, on page 11 — Contains the procedure for

mounting the NCS-57C3-MOD-S and NCS-57C3-MOD-SE-S chassis in a 2-post rack.

•Rack Mount the NCS-57C1 Chassis in a 4-Post Rack with Sliders, on page 16 — Contains the procedure

for mounting the NCS-57C1 chassis in a 4-post rack.

•Rack-Mount the NCS-57B1 Chassis in a 4-Post Rack, on page 13 — Contains the procedure for mounting

the NCS-57B1-6D24-SYS and NCS-57B1-5DSE-SYS chassis in a 4-post rack.

•Rack Mount the NCS-57C3-MOD Chassis in a 4-Post Rack using Sliders, on page 22 — Contains the

procedure for mounting the NCS-57C3-MOD-S and NCS-57C3-MOD-SE-S chassis in a 4-post rack

using a sliders.

Install the Chassis

Rack Mount the Chassis

Rack Mount the NCS-57B1 Chassis in a 2-Post Rack

This section describes how to use the rack-mount kit provided with the chassis, to install the following chassis

into a cabinet or a 2-post rack:

• NCS-57B1-5DSE-SYS

• NCS-57B1-6D24-SYS

If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.

Caution

The following table lists the items contained in the rack-mount kit provided with the routers.

Table 2: Router Rack-Mount Kit

Part DescriptionQuantity

Rack-mount brackets2

M4 x 6-mm Phillips counter sink screws8

Step 1 Install two rack-mount brackets to the router as follows:

a) Position the router so that its ports will be in the cold aisle.

b) With the bracket ears aligned to the front of the chassis, position a rack-mount bracket on the side of the chassis so

that the four holes are aligned to four of the screw holes on the side of the chassis.

c) Use four M4 screws with 12 in-lbs (1.4 N-m) to attach the bracket to the chassis

d) Repeat Steps 1b and 1c with the other rack-mount bracket on the other side of the router.

Install the Chassis

Rack Mount the NCS-57B1 Chassis in a 2-Post Rack

Figure 2: Rack-Mount Brackets

Cable guide2Rack-mount brackets1

M4 x 6 Phillips counter sink

screws

Step 2 Install the router onto the 2-post rack as follows:

a) With two people, lift the router into position between the two rack posts.

b) Move the router until the rack-mount brackets come in contact with two rack posts.

c) Hold the chassis level while the second person inserts two screws (12-24 or 10-32, depending on the rack type) in

each of the two rack-mount brackets (using a total of four screws) and into the cage nuts or threaded holes in the

vertical rack-mounting rails.

d) Tighten the 10-32 screws to 20 in-lb (2.26 N.m) or tighten the 12-24 screws to 30 in-lb (3.39 N.m).

Install the Chassis

Rack Mount the NCS-57B1 Chassis in a 2-Post Rack

Figure 3: 2-Post Rack Mount

Rack Mount the NCS-57C1 Chassis in a 2-Post Rack with Sliders

This section describes how to use the rack-mount kit provided with the NCS-57C1 chassis, to install the

chassis into a cabinet or a 2-post rack.

If the rack is on wheels, ensure that the brakes are engaged or that the rack is otherwise stabilized.

Caution

The following table lists the items contained in the rack-mount kit provided with the routers.

Table 3: 2 Post Rack-Mount Kit

Part DescriptionQuantity

Slider assembly - left and right2

Slider brackets - left and right2

12-24 Phillips pan-head screws10

M4 x 6.5-mm Phillips flat head screws12

M4 x 8-mm Phillips pan head screws2

Install the Chassis

Rack Mount the NCS-57C1 Chassis in a 2-Post Rack with Sliders

Part DescriptionQuantity

(only 23-inch rack-mount kit) Extension brackets4

Ground lug1

Step 1 (Only 23-inch rack post) Mount the extension brackets on the 23-inch rack post. Use three 12-24 Phillips pan-head screws

with 30 in-lb (3.39 N.m) to attach each extension bracket to the rear and front rack post on either sides.

Figure 4: Mount Extension Brackets on a 23-inch 2-Post Rack

Screws2Extension brackets1

Step 2 Install the slider assembly on the rack as follows:

a) Align the outer slider of the left slider assembly to the rear post rack holes and the inner slider of the left slider

assembly to the front post rack holes. The slider rail should be at the bottom.

b) Use three 12-24 Phillips pan-head screws (two on the rear side and one on the front side) with 30 in-lb (3.39 N.m)

to attach the slider assembly to the rear and front rack post.

c) Repeat Steps 2a and 2b with the other slider assembly on the other side of the router.

Install the Chassis

Rack Mount the NCS-57C1 Chassis in a 2-Post Rack with Sliders

Figure 5: Rack-Mount Slider Assembly on a 19-inch 2-Post Rack

Slider rail2Slider assembly1

Screws3

In case of a 23-inch 2-post rack, mount the slider assembly on the extension brackets following the same

procedure outlined in Step 2.

Note

Install the Chassis

Rack Mount the NCS-57C1 Chassis in a 2-Post Rack with Sliders

Figure 6: Rack-Mount Slider Assembly on a 23-inch 2-Post Rack

Slider rail2Slider assembly1

Extension bracket4Screws3

Step 3 Install slider brackets to the router as follows:

a) Determine which end of the chassis is to be located in the cold aisle as follows:

• If the router has port-side intake modules, position the router so that the ports are in the cold aisle.

• If the router has port-side exhaust modules, position the router so that the fan and power supply modules are in

the cold aisle.

b) With the slider bracket ears aligned to the front of the chassis as shown in the image, use six M4x6.5mm flat head

screws with 12 in-lbs (1.4 N-m) to attach the bracket to the chassis

c) Repeat Steps 3b and 3c with the other slider bracket on the other side of the router.

Install the Chassis

Rack Mount the NCS-57C1 Chassis in a 2-Post Rack with Sliders

Figure 7: Mount Slider Brackets

Screws2Slider brackets1

Step 4 Install the router onto the 2-post rack as follows:

a) Holding the router with both hands, position the back of the router between the front posts of the rack.

b) Move the router until the slider brackets come in contact with slider rails installed in the rack. Slide the slider brackets

onto the slider rails, and then gently move the router all the way into the rack.

c) Hold the chassis level while the second person inserts two pan-head screws (12-24) in each of the two rack-mount

brackets (using a total of four screws) and into the cage nuts or threaded holes in the vertical rack-mounting rails.

d) Tighten the 12-24 screws to 30 in-lb (3.39 N.m).

Install the Chassis

Rack Mount the NCS-57C1 Chassis in a 2-Post Rack with Sliders

Figure 8: 19-inch 2-Post Rack Mount Chassis

Figure 9: 23-inch 2-Post Rack Mount Chassis

Install the Chassis

Rack Mount the NCS-57C1 Chassis in a 2-Post Rack with Sliders

Table des matières

Autres manuels Cisco Routeur réseau

Cisco

Cisco ASA 5508-X Manuel utilisateur

Cisco

Cisco ASR 14000 Series Manuel d'installation

Cisco

Cisco XR 12000 Manuel utilisateur

Cisco

Cisco 1100 Series Mode d’emploi

Cisco

Cisco DVB CAR100 Series Manuel utilisateur

Cisco

Cisco 8201 Manuel utilisateur

Cisco

Cisco ASR 9000 Series Manuel utilisateur

Cisco

Cisco RV016 - Small Business - 10/100 VPN Router Manuel utilisateur

Cisco

Cisco Catalyst IR1800 Rugged Series Manuel utilisateur

Cisco

Cisco WS-C2950-24 Manuel utilisateur

Cisco

Cisco Unified Communications Manager 8.5(1) Manuel utilisateur

Cisco

Cisco 4948 Series Manuel utilisateur

Cisco

Cisco AIRONET CB21AG Manuel utilisateur

Cisco

Cisco 1700 series Manuel utilisateur

Cisco

Cisco ASR 5000 Series Manuel utilisateur

Cisco

Cisco NCS 4000 Series Manuel utilisateur

Cisco

Cisco 860 Series Manuel

Cisco

Cisco 1711 - Security Access Router Manuel utilisateur

Cisco

Cisco ASR 902 Mode d'emploi

Cisco

Cisco 15310-CL Manuel utilisateur

Cisco

Cisco QuickVPN - PC Mode d’emploi

Cisco

Cisco 860 Series Manuel

Cisco

Cisco 10000 Series Manuel utilisateur

Cisco

Cisco GSR12/60 - 12012 Router -AnyLAN Manuel de l'opérateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur