Cisco 700 series Manuel utilisateur

Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Cisco 700 Series Router Cabling and Setup

Quick Start Guide

This document describes the basic process of cabling and configuring the Internet access device, the

Cisco 700 series router. For advanced cabling information, refer to the Cisco 700 Series Router

Installation Guide. For advanced configuration information, refer to the Cisco 700 Series Router

Command Reference and the Cisco 700 Series Router Software Conﬁguration Guide. These documents can

be found on the Cisco Documentation CD-ROM and Cisco Connection Online (CCO).

Parts List

•One Cisco 700 series router

•One yellow Ethernet cable

•One red ISDN U cable (Cisco 776 routers only)

•One orange ISDN S/T cable (Cisco 761 and 775 routers only)

•One RJ-45-to-RJ-11 adapter

•One blue config cable

•One black power supply

•One black power supply cord

•One Cisco Fast Step CD-ROM

Note Additional parts might be required to install Cisco775 and Cisco 776 routers. An Ethernet

crossover cable must be used to connect a hub to the router. Depending on the country, you

might need a phone port adapter to connect an analog telephone. These parts must be

provided by the user.

78-10157-01

Verify the PC Setup

Before you begin, verify that each computer that will be connected to the computer has a network

interface card (NIC) installed and TCP/IP loaded.

Connect a 760 Series Router to a PC or Hub

Step 1 If you are connecting the router to a computer, connect the yellow Ethernet cable from the yellow

Ethernet port on the rear panel of the router to the Ethernet port on the network interface card on the

computer.

If you are connecting the router to a hub, connect the yellow Ethernet cable from the yellow Ethernet

port on the rear panel of the router to an Ethernet port on the hub.

Step 2 If you are connecting the router to a computer, to a hub, set the node-hub switch to the “NODE”

position and connect the computers to the hub as described in the documentation provided with your

hub.

CONFIG

+5V ---1.5A +/-5%

-30V--- 0.2A +/-25%

ISDN S/T

CISCO 776

10BASET

NODE HUB

30046

CONFIG

+5V ---1.5A +/-5%

-30V--- 0.2A +/-25%

ISDN S/T

CISCO 776

10BASET

NODE HUB

30047

78-10157-01

Connect a 770 Series Router to a PC or Hub

Step 1 If you are connecting to a computer, connect a yellow Ethernet cable from a yellow Ethernet port on

the rear panel of the router to the Ethernet port on the network interface card on the computer. If you

are connecting the router to a hub, omit this step.

Step 2 If you are connecting to a hub, connect an Ethernet crossover cable (not included) from a yellow

Ethernet port on the rear panel of the router to an Ethernet port on the hub. Otherwise omit this step.

CONFIG 1

+5V ---1.5A +/-5%

-30V--- 0.2A +/-25%

NT-1

ISDN S/T

CISCO 776

ETHERNET

ISDN U

30048

30049

CONFIG 1

+5V ---1.5A +/-5%

-30V--- 0.2A +/-25%

NT-1

ISDN S/T

CISCO 776

ETHERNET

ISDN U

78-10157-01

Connect the ISDN Line

This section shows how to connect the router to the ISDN.

Connect a Cisco 762 or Cisco 776 Router to the ISDN Line

Step 1 Connect the red ISDN U cable to the red port labeled ISDN U on the rear panel of your router.

Step 2 Connect the other end of the ISDN U cable directly to an RJ-45 ISDN wall jack.

Note If necessary, use the enclosed RJ-45-to-RJ-11 adapter to connect to an RJ-11 ISDN wall

jack.

Connect a Cisco 761 or Cisco 775 Router to the ISDN Line

Step 1 Outside North America, connect the orange ISDN S/T cable to the orange ISDN S/T port on the rear

panel of your router. Inside North America, see the Cisco 700 Series Router Installation Guide for

instructions.

CONFIG

+5V ---1.5A +/-5%

-30V--- 0.2A +/-25%

NT-1

ISDN S/T

CISCO 776

10BASET

ISDN U

NODE HUB

30050

30051

CONFIG

+5V ---1.5A +/-5%

-30V--- 0.2A +/-25%

ISDN S/T

CISCO 776

10BASET

NODE HUB

30052

78-10157-01

Step 2 Connect the other end of the ISDN S/T cable to the ISDN wall socket.

Note If necessary, use the enclosed RJ-45-to-RJ-11 adapter to connect to an RJ-11 ISDN wall

jack.

Connect the Power and Turn On the Router

This section describes the procedure for supplying power to the router.

Step 1 Connect the power supply cable to the round, black power connector on the rear panel of the router,

connect the power supply cord to the power supply, and connect the power supply cord to an electrical

outlet.

Step 2 Turn on the router by using the on/off switch on the rear panel. The green RDY LED (and the NT1

LED on the Cisco 772 and Cisco 776) on the front panel of your router turns on. Your router is now

ready to be set up.

If the green RDY LED is not on, refer to the “Troubleshooting Cisco 700 Series Routers” chapter in

the Cisco 700 Series Router Installation Guide.

30051

CONFIG

+5V ---1.5A +/-5%

-30V--- 0.2A +/-25%

ISDN S/T

CISCO 776

ETHERNET

1234

BRI

???

30053

78-10157-01

Setup the Router to Access a Corporate Network or Internet

Service Provider

A Cisco Fast Step CD-ROM and a RVS-COM Lite CD-ROM is included with your router. We

recommend that you use Cisco Fast Step software to set up the router and RVS-COM Lite software for

Common ISDN Application Programmers Interface (CAPI) support.

Cisco Fast Step Software

Cisco Fast Step software simplifies the setup and monitoring of Cisco routers. It runs on Microsoft

Windows 95, Windows 98, and Windows NT 4.0 personal computer systems. The Cisco Fast Step

software CD-ROM is included with your router. It is also available on Cisco Connection Online at

http://www.cisco.com/pcgi-bin/tablebuild.pl/faststep. If you have questions about Cisco Fast Step

software, please E-mail the following alias for more information: [email protected]

Insert the CD in the CD-ROM drive. The installation wizard starts automatically.

If you inserted the CD in the drive and the setup program did not start automatically, launch the

installation wizard by following these instructions:

Step 1 Double-click the My Computer icon.

Step 2 Double-click the CD icon.

Step 3 Double-click the ImLanguageSelect.exe icon, and follow the on-screen instructions.

If you downloaded the software from Cisco Connection Online, launch the installation wizard by

following these instructions:

Step 4 Uncompress the Cisco Fast Step files, retaining the directory structure.

Step 5 Double-click the Setup.exe icon in the disk1 directory, and follow the on-screen instructions.

RVS-COM Lite Support

The RVS-COM Lite software provides CAPI support. If you already have a terminal adapter with CAPI

installed, you must uninstall the old version of CAPI, install a network interface card, and install the

Cisco-supplied RVS-COM Lite upgrade on every PC.

Make sure you do the following:

•Install the RVS-RVS-COM Lite software after you have used Cisco Fast Step Setup to configure the

router.

•Install RVS-COM Lite on every PC on the Ethernet.

RVS-COM Lite Installation

Place the RVS-COM Lite CD into the CD-ROM drive of your computer. It should start automatically.

If it does not start or you have any questions about the RVS-COM Lite software, refer to the

documentation provided with the RVS-COM Lite CD-ROM.

78-10157-01

Access Registrar, AccessPath, Any to Any, AtmDirector, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, the Cisco logo, Cisco Certified

Internetwork Expert logo, CiscoLink, the Cisco Management Connection logo, the Cisco NetWorks logo, the Cisco Powered Network logo, Cisco Systems

Capital, the Cisco Systems Capital logo, Cisco Systems Networking Academy, the Cisco Systems Networking Academy logo, the Cisco Technologies logo,

ConnectWay, Fast Step, FireRunner, GigaStack, IGX, Internet Quotient, Kernel Proxy, MGX, MultiPath Data, MultiPath Voice, Natural Network Viewer,

NetSonar, Network Registrar, Packet, PIX, Point and Click Internetworking, Policy Builder, Precept, Secure Script, ServiceWay, SlideCast, SMARTnet,

The Cell, TrafficDirector, TransPath, ViewRunner, Virtual Service Node, VisionWay, VlanDirector, WebViewer, Workgroup Director, and Workgroup

Stack are trademarks; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, The Internet Economy, and The New

Internet Economy are service marks; and ASIST, BPX, Catalyst, Cisco, Cisco IOS, the Cisco IOS logo, Cisco Systems, the Cisco Systems logo, the Cisco

Systems Cisco Press logo, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastLink, FastPAD, FastSwitch, GeoTel, IOS, IP/TV, IPX,

LightStream, LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, TeleRouter, and VCO are registered

trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain other countries. All other trademarks mentioned in this document are the property

of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any of its resellers. (9910R)

Autres manuels pour 700 series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cisco Routeur réseau

Cisco

Cisco Profile Series Mode d’emploi

Cisco

Cisco 7600 Series Manuel utilisateur

Cisco

Cisco Catalyst IR1800 Rugged Series Manuel utilisateur

Cisco

Cisco 7206VXR NPE-400 Manuel utilisateur

Cisco

Cisco Linksys WRT54G3GV2-ST Mode d’emploi

Cisco

Cisco 500 Series Manuel utilisateur

Cisco

Cisco ASR 9000 Series Manuel utilisateur

Cisco

Cisco 700 series Manuel utilisateur

Cisco

Cisco WRT54G Manuel utilisateur

Cisco

Cisco ASR-920-20SZ-M Manuel

Cisco

Cisco CPA2501 Manuel utilisateur

Cisco

Cisco 1751V Manuel

Cisco

Cisco 1721 - VPN Security Router Bundle Manuel

Cisco

Cisco 4948 Series Manuel utilisateur

Cisco

Cisco ASR 903 Mode d’emploi

Cisco

Cisco WRT350N Manuel utilisateur

Cisco

Cisco ASR 1002-HX Manuel utilisateur

Cisco

Cisco ASR 9001 Manuel

Cisco

Cisco Small Business RV315W Mode d’emploi

Cisco

Cisco NCS 6000 Series Manuel utilisateur

Cisco

Cisco 7603 - Modular Expansion Base Manuel utilisateur

Cisco

Cisco IR809 Instructions d'utilisation et de sécurité

Cisco

Cisco 5915 Guide de démarrage rapide

Cisco

Cisco Universal Broadband Router uBR7200 Manuel

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

EnGenius

EnGenius ESR-9710 Manuel utilisateur

LevelOne

LevelOne FBR-1416 Manuel utilisateur

Dynacord

Dynacord Promatrix 6000 Manuel utilisateur

Lorex

Lorex F5D8230-4 Manuel utilisateur