Christie G Series Guide de démarrage rapide
Upgrade Instructions for G Series Software version 02.03 Page 1 of 5
(FW P/N 001-112143-03 Rev 2)
UPGRADE INSTRUCTIONS
G Series version 02.03
Applies to the following projectors:
DHD550-G, DWU550-G
Upgrade Summary:
1. The update package contains 3 files:
-Christie GSeries C02.03 FW AN Update Wizard.msi
-20130719_PWC808_B2231_x32_128M.zip
-20130719_PWC808_B2231_x64_128M.zip
2. Steps for upgrading are:
-Install the FW wizard to Windows PC.
-With USB connection, upgrade WebUI/networking FW version B22.31
-With RJ45/network connection and using the wizards:
Upgrade main projector scaler FW version C02.03
Upgrade PIC code version A29.06
3. Two cables are required for the upgrade:
-AN cable (RJ45)
-USB cable (USB to Mini-USB)
4. It is recommended to use a computer/laptop with Windows XP/
Window 7, Internet Explorer 7 and hi her, with automatic
screensavers and screen timeouts disabled.
Stage 1 – Install Update files and prepare computer
5. Determine whether your computer is running a 32-bit or 64-bit version of Windows.
(http://support.microsoft.com/kb/827218#method2 for help)
6. Unzip the relevant files onto your computer:
-For 32-bit operating systems use x32: 20130719_PWC808_B2231_x32_128M.zip
-For 64-bit operating systems use x64: 20130719_PWC808_B2231_x64_128M.zip
7. Install the C02.03 wizard on your computer. This will install 2 icons on your desktop:
"Christie GSeries A29.06 PIC FW AN Update Wizard"
"Christie GSeries C02.03 System FW AN Update Wizard"
Stage 2 – Upgrade WebUI to version B22.31
** NOTE: This upgrade must be done first, before the Main FW upgrade.
A USB to Mini-USB connection is required between the computer and projector.
Put projector into pro rammin mode
8. Unplu the power cable, and then plu in.
AC switch on, ensure the projector is in standby mode (The 3 status EDs are off).
Page 2 of 5 Upgrade Instructions for GSeries Software version 02.03
(FW P/N 001-112143-03 Rev 2)
** If the projector is powered on automatically, turn off “AC Power On” by using the projector Main Menu ->
Configuration -> Power Management -> AC Power On. Then repeat step 8.
9. Put the projector into flash upgrade mode by holding the “UP” key on the built-in keypad and then press and
hold the power button (at the same time as “UP”) until the 3 status EDs begin to flash green and red
alternately (hold for approximately 6 seconds).
10. Connect the USB cable between the computer and projector.
Install USB driver on computer
11. Install the USB driver from the file in step 6 (This step only needs to be completed successfully one time unless
you change USB ports)
-Make sure that you have administrative privileges on your PC.
-Open your Device Manager. To do this manually:
oHold the windows key and press R
oType “mmc -open \WINDOWS\system32\devmgmt.msc” without the quotations and run
-In Device Manager, look for and expand the USB device. (need active connection to projector to see this). It
may show as “USB Device”, “Unknown Device” or “Other
devices”.
-Right click on the correct one and choose “Update
Driver…”. Browse and select the driver file from the
directory in which you unzipped the files in step 6.
e.g.
C:\Christie\20130719_PWC808_B2231_x32_128M_User
\FlashUp rader_x32_driver
If you are running a 64-bit operating system, choose the
file from the “FlashUp rader_x64_driver” folder.
-Allow the installation to complete then press finish.
-After the installation, ensure “LibUSB-Win32 Devices” is
shown in Device Manager.
Up rade the firmware
12. In the Folder extracted in step 6, run the correct file
for your operating system:
- FlashUp rader_x32.exe (for 32-bit systems) or
- FlashUp rader_x64.exe (for 64-bit systems)
13. A window will appear, ensure the settings match the
picture on the right.
14. Press flash and wait until the “Flash Complete” popup
appears. After it is complete, unplug the AC power
from the projector.
** If the FlashUpgrader application is stuck at “Waiting
for target reset” for more than 30 seconds, try
unplugging the AC power and restarting at step 8.
** Open Windows Device Manager and ensure “LibUSB-
Win32 Devices” is shown properly at step 11.
Upgrade Instructions for GSeries Software version 02.03 Page 3 of 5
(FW P/N 001-112143-03 Rev 2)
Stage 3 – Set up network connection to the projector
An Ethernet connection is required between the computer and projector.
15. In the projector’s menu Configuration->Communications->Network:
- Deselect DHCP (switch it off)
- Wait approximately 45 seconds for the Network Settings to take
effect (i.e. until the menu settings are no longer grayed out)
16. Connect the projector and the PC.
- A direct RJ45 connection is recommended.
- If the connection is through a switch or router, ensure that there are no duplicate IP addresses for any
equipment connected via the switch.
- Default settings that work are: (Other settings may be used)
•Projector IP address 192.168.0.100
•Computer IP address 192.168.0.101
•Subnet Mask on both 255.255.255.0
Stage 4 – Upgrade Main FW to version C02.03
The RJ45 connection (as described in Stage 3) is required
between the computer and projector.
17. Start with the projector AC switch off.
18. Start the upgrade wizard from the desktop icon.
“Christie GSeries C02.03 System FW LAN Update
Wizard”
19. Confirm it is the correct firmware for the projector
model.
20. Turn the projector on and wait until the Source
message box is displayed on the bottom left of the
image.
21. Follow the instructions in the Upgrade Wizard. The
Page 4 of 5 Upgrade Instructions for GSeries Software version 02.03
(FW P/N 001-112143-03 Rev 2)
upgrade should take about 18 minutes.
Step 5 – Upgrade PIC FW to version A29.06
The RJ45 connection is required between the computer
and projector.
22. Start the Upgrade Wizard from the desktop icon.
“Christie GSeries A29.06 PIC FW LAN Update
Wizard”
23. Confirm it is the correct firmware for the projector
model.
24. Turn the projector on and wait until the Source
message box is displayed on the bottom left of the
image.
25. Follow the instructions in the Upgrade Wizard. The
upgrade should take less than a minute.
Stage 6 - Update completion & confirmation
26. After the upgrade has finished, the projector will return to Standby mode. Unplug the projector and plug it in
again, then turn the projector on. The upgrade should be complete.
** NOTE: Some projectors may require a few AC power cycles to
return to normal mode. An indication that a power cycle
is required is the keys on the built in keypad will all be lit
and some may appear purple.
27. Go to the projector’s factory menu (on the IR remote, press “Auto”,
“ eft”, “ eft”, “ eft”) and confirm that the versions are correct and
the projector model name is displayed correctly:
Model Name: DHD550-G or DWU550-G (must match the
model name on the projector’s label)
Main Firmware: C02.03
PIC Firmware: A29.06
Network Firmware: B22.31
Upgrade Instructions for GSeries Software version 02.03 Page 5 of 5
(FW P/N 001-112143-03 Rev 2)
28. Perform a Network Factory Reset to ensure that the password changes in this version take effect.
Go to the projector Main Menu -> Configuration -> Communications -> Network -> Network Factory Reset…
Stage 7 – Christie Presenter Update
29. After completion of the upgrade, and as the projector is being operated, the presentation tool Christie
Presenter version 2.2.5.0 may be downloaded directly from the projector to your computer/laptop:
- Open a web page connection to the projector
- Download Christie Presenter from the link on the main page ( og in is not required).
Autres manuels pour G Series
1
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Christie Projecteur
Christie
Christie DCP Series Manuel utilisateur
Christie
Christie CP2208-LP Guide de l'utilisateur
Christie
Christie LWU720i Manuel utilisateur
Christie
Christie Cinema 4K-RGB CP4315-RGB Manuel utilisateur
Christie
Christie DS+60 Manuel utilisateur
Christie
Christie Roadie HD+35K Manuel utilisateur
Christie
Christie CP43XX-RGB Series Manuel utilisateur
Christie
Christie LX400 Manuel utilisateur
Christie
Christie CP2220 Manuel utilisateur
Christie
Christie CP4230 Manuel utilisateur
Christie
Christie DHD600-G Manuel utilisateur
Christie
Christie DWU1052 Manuel utilisateur
Christie
Christie 38-VIV208-01 Manuel utilisateur
Christie
Christie D4K40-RGB Mode d’emploi
Christie
Christie Mirage 4K40-RGB Manuel utilisateur
Christie
Christie LWU720i Manuel utilisateur
Christie
Christie Cinema 4K-RGB CP4325-RGB Manuel utilisateur
Christie
Christie CAPTIVA DHD400S Manuel utilisateur
Christie
Christie DW30 Manuel utilisateur
Christie
Christie CineLife+ Series Manuel d'utilisation
Manuels Projecteur populaires d'autres marques
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur
NEC
NEC NP600S EDU Manuel utilisateur
BenQ
BenQ SH753P Manuel utilisateur
Eiki
Eiki EK-623U series Manuel utilisateur
Epson
Epson PowerLite Pro Cinema 6020UB Manuel utilisateur
Epson
Epson PowerLite Home Cinema 705HD Manuel utilisateur
