Chamberlain MC100C Manuel utilisateur

To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control

transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.

• ALWAYS keep gate or door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

Universal Mini Remote Control

Read instructions thoroughly BEFORE beginning.

If using the Universal Mini Remote Control with residential door openers, the remote control must be used only

with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are

always located on or near the bottom of the door track.

STOP

MODELS MC100,

MC100C, MC100-P2

AND MC100C-P2

TABLE OF CONTENTS

GETTING STARTED ........................................................................... 2

LOCATE THE PROGRAM/LEARN BUTTON......................................3-7

Chamberlain®products................................................................ 3

LiftMaster®products.................................................................... 4

Overhead Door®products ............................................................ 4

Genie®products............................................................................ 5

Linear®products........................................................................... 6

Wayne Dalton®products.............................................................. 6

Stanley®products......................................................................... 7

GARAGE DOOR OPENERS ..............................................................8-9

Programming to a garage door opener with a

Program/LEARN button ................................................................ 8

Programming to a Genie®Intellicode®2

garage door opener...................................................................... 9

COMMERCIAL DOOR OPERATORS ................................................. 10

Programming to a commercial door operator

with a Program/LEARN button................................................... 10

GATE OPERATORS.......................................................................... 11

Program to a gate operator

with a Program/LEARN button................................................... 11

EXTERNAL RECEIVERS................................................................... 12

Programming to an external receiver

with a Program/LEARN button................................................... 12

MYQ LIGHT CONTROLS .................................................................. 13

NEED HELP? ................................................................................... 14

BATTERY ........................................................................................ 15

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

GETTING STARTED

The Universal Mini Remote Control can be programmed to activate up to two products, such as a garage door opener, MyQ®light

controls, gate operator, or commercial door operator. Each button on the remote control works independently of the other and must be

programmed separately. The images throughout this manual are for reference only and your product may look different.

Bottom Button

Top Button

Garage Door Opener Commercial Door OperatorGate Operator

LED

Key Ring Holder

You will need to locate the Program/LEARN button on your product before you start programming.

GARAGE DOOR OPENERS

The Program/LEARN button is typically located on the back or side panel

of your garage door opener. Newer garage door openers may have a

Program/Learn button located on the door control. Your Program/LEARN

button may have a different name (SMART button, SET button, etc.). For

help locating your Program/LEARN button refer to the Table of Contents

in this manual or contact your garage door opener manufacturer.

COMMERCIAL DOOR OPERATORS

The Program/LEARN button is typically located on the logic board of your

operator. Your Program/LEARN button may have a different name

(RADIO button, XMITTER button, etc.). For help locating your Program/

LEARN button contact your door operator manufacturer.

GATE OPERATORS

The Program/LEARN button is typically located on the control board of

your operator. Your Program/LEARN button may have a different name

(RADIO button, XMITTER button, etc.). For help locating your Program/

LEARN button contact your gate operator manufacturer.

EXTERNAL RECEIVER

Some products do not

have a Program/LEARN

button. In this case, the

Program/LEARN button

will be located in an

external receiver. The

receiver will be located on

the product or mounted

nearby. Follow the

programming instructions

for an external receiver.

LOCATE THE PROGRAM/LEARN BUTTON

CHAMBERLAIN PRODUCTS

LOCATE THE PROGRAM/LEARN BUTTON

OVERHEAD DOOR PRODUCTS

LIFTMASTER PRODUCTS

Yellow Learn

Button

Purple Learn

Button

Orange Learn

Button

Green Learn

Button

Learn Code

Button

LOCATE THE PROGRAM/LEARN BUTTON

Learn Code

Button

Program Set Button

GENIE PRODUCTS

LOCATE THE PROGRAM/LEARN BUTTON

LINEAR PRODUCTS

Learn

Button

Learn

Button

Program SW

Button

WAYNE-DALTON PRODUCTS

LOCATE THE LEARN BUTTON

STANLEY PRODUCTS

Learn Button

GARAGE DOOR OPENERS

Programming to a Garage Door Opener with a Program/LEARN Button

The Program/LEARN button is typically located on the back or side panel of the garage door opener or an external receiver. For help

locating your Program/LEARN button refer to the Help section in this manual or contact your garage door opener manufacturer.

The Mini Remote Control is pre-programmed to work with a Chamberlain garage door opener with a yellow learn button. Press and

release the yellow learn button, then press and hold the button on the remote control you would like to use. If programming is not

successful, proceed through the steps below.

If you have a Genie®Intellicode®2 garage door opener go to the next page. If you have an external receiver, see External Receivers

page 12.

The images throughout this manual are for reference only and your product may look different.

Bottom Button

1Start with your garage door closed. 2Press and hold bottom button on the remote control until

the blue LED stays solid (approximately 15 seconds) then

release the button.

3Press and release the Program/LEARN button on your

garage door opener. or 2 times on your door control.

4On the remote control, press and release the button that

you would like to program twice. The blue LED will blink

and the remote control will begin sending the

preprogrammed codes to the garage door opener.

Transmission can take up to 60 seconds.

5 6

When the garage door begins to open, immediately press

and release either of the buttons on the remote control to

confirm the code and exit programming.

LED

Test the remote control by pressing the button you

programmed in step 4. If the garage door opener does not

activate, repeat the programming steps.

IMPORTANT: The remote will activate your garage door during

programming. Ensure garage door is clear of ALL obstructions.

LED

Programming to a Genie®Intellicode®2 Garage Door Opener

Before starting, you MUST have an existing Genie®Intellicode®2 remote control programmed to the garage door opener. For help

programming a Genie Intellicode 2 remote control to your Genie operator, see your Genie owner’s manual.

The images throughout this manual are for reference only and your product may look different.

GARAGE DOOR OPENERS (continued)

1 2

On the garage door opener, press and hold the

Program/Set button until both the long and short LED’s

light up BLUE.

Press and release the Program/Set button and the long

LED will flash PURPLE.

On the Genie®remote control, press and release the

button that is already programmed to the garage door

opener. Both LED’s will flash PURPLE.

Bottom Button

Start with your garage door closed. Press and hold bottom button on the remote control until

the blue LED stays solid (approximately 15 seconds) then

release the button.

On the remote control, press and release the button that

you would like to program 3 times. The blue LED will blink

for up to 60 seconds.

Wait for the garage door to open, then press and release

either of the buttons on the remote to complete

programming.

LED

Test the remote control by pressing the button you

programmed in step 6. If the garage door opener does not

activate, repeat the programming steps.

IMPORTANT: The remote will activate your garage door during

programming. Ensure door is clear of ALL obstructions.

LED

COMMERCIAL DOOR OPERATORS

Programming to a Commercial Door Operator with a Program/LEARN Button

The Program/LEARN button is typically located on the logic board of the operator or an external receiver. For help locating your

Program/LEARN button contact your commercial door operator manufacturer.

The Mini Remote Control comes pre-programmed to work with a Chamberlain branded Commercial Door Operator with a yellow learn

button. Press and release the yellow learn button, then press and hold the button on the remote control you would like to use. If

programming is not successful, proceed through the steps below.

If you have an external receiver, proceed to the External Receiver programming page. See the Table of Contents for page location. The images throughout this manual are

for reference only and your product may look different.

Program/LEARN

Button*

Program LED

Program/LEARN

Button*

* Depending on your product, the Program/LEARN button may have a different

name (use the button for programming remote controls).

Bottom Button

1Start with your commercial door closed. 2Press and hold bottom button on the remote control until

the blue LED stays solid (approximately 15 seconds) then

release the button.

3Press and release the Program/LEARN button* on your

commercial door operator. The program LED will

illuminate.

Wait for the program LED on the commercial door

operator to blink, then press and release the Program/

LEARN button to exit program mode.

4On the remote control, press and release the button that

you would like to program twice. The blue LED will blink

for up to 60 seconds.

5 6 Wait for the commercial door to open, then press and

release either of the buttons on the remote.

LED

Test the remote control by pressing the button you

programmed in step 4. If the commercial door operator

does not activate, repeat the programming steps.

IMPORTANT: The remote will

activate your commercial door

during programming. Ensure

door is clear of ALL

obstructions.

LED

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Chamberlain Télécommande

Chamberlain

Chamberlain LiftMaster 94330E Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional 33LM Manuel utilisateur

Chamberlain

Chamberlain LiftMaster 371LM Manuel utilisateur

Chamberlain

Chamberlain 893LM Manuel utilisateur

Chamberlain

Chamberlain 850CB Manuel utilisateur

Chamberlain

Chamberlain 375LM Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional 98685E Manuel utilisateur

Chamberlain

Chamberlain 895MAX Manuel utilisateur

Chamberlain

Chamberlain TX4REV-F Manuel utilisateur

Chamberlain

Chamberlain 892LT Manuel utilisateur

Chamberlain

Chamberlain Security Plus 96LMC Manuel utilisateur

Chamberlain

Chamberlain 891LM Manuel utilisateur

Chamberlain

Chamberlain 972MOM Moore-o-Matic Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Security+ 971LM Manuel utilisateur

Chamberlain

Chamberlain TriCode Systems Manuel utilisateur

Chamberlain

Chamberlain 375UT Manuel utilisateur

Chamberlain

Chamberlain LiftMaster 375UT Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional 82LM Manuel utilisateur

Chamberlain

Chamberlain 54332EML Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Security+ 973TB Manuel utilisateur

Chamberlain

Chamberlain 953EV Manuel utilisateur

Chamberlain

Chamberlain ARQ TM100 Manuel utilisateur

Chamberlain

Chamberlain Clicker KLIK1U Manuel utilisateur

Chamberlain

Chamberlain 972LM Security? Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation