Chamberlain MC100AMLR Manuel utilisateur

The Universal Garage Door Opener Remote

Control can be programmed to operate up to two

motors. Each button on the remote control works

independently of the other and must be

programmed separately.

The images throughout this manual are for

reference only and your product may differ from

the images shown.

MC100AML

UNIVERSAL GARAGE DOOR OPENER

REMOTE CONTROL

To prevent possible SERIOUS INJURY or DEATH from a

moving door:

ALWAYS keep remote controls out of reach of children. NEVER permit

children to operate or play with remote control transmitters.

•

Activate a door ONLY when it can be seen clearly, is properly adjusted

and there are no obstructions.

•

ALWAYS keep a door in sight until completely closed. NEVER permit

anyone to cross the path of a moving door or gate.

•

BATTERY

CR2032 Battery

Screw

Replacing the battery:

WARNING! This product contains a button/coin cell battery.

To prevent possible SERIOUS INJURY or DEATH:

• The battery is hazardous.

• Keep new and used batteries away from children.

• Do not ingest battery. Chemical burn hazard.

• If the coin cell battery is swallowed or placed inside any part

of the body, it can cause severe or fatal injuries in 2 hours or

less.

• If the battery compartment does not close securely, stop using the product

and keep away from children.

• If you think batteries might have been swallowed or placed inside any part

of the body, call the 24-hour Poisons Information Centre on 13 11 26 in

Australia, or the 24-hour National Poisons Centre on 0800 764 766 in

New Zealand, or seek immediate medical attention.

• Dispose of used coin/button cell batteries immediately and safely. Flat

batteries can still be dangerous.

Visit chamberlaindiy.com.au/universal or chamberlaindiy.co.nz/universal

for up to date information on the models that the universal remote is

compatible with.

The Universal Garage Door Opener Remote Control is compatible

with:

COMPATIBILTY TABLE

Brand Code Type Frequency Learn

Button

Label

Model Number:

ATA TrioCode128 433.47 / 433.92 /

434.37MHz

DOOR

CODE

GDO6, GDO7, GDO8, GDO9 ENDURO, GDO9

DYNAMO, GDO10, GDO11, TEMPO™ ATS-2

ATA TrioCode 433.47 / 433.92 /

434.37MHz

DOOR

CODE

GDO6, GDO7, GDO8, GDO9 ENDURO, GDO9

DYNAMO, GD1O, GDO11, RD40

ATA SecuraCode 433.92MHz DOOR

CODE

GDO4, GDO5 Securacode, GDO6, GDO7, GDO8

Avanti Rolling 433.92MHz LEARN MPS6, MPS12, DPS12, T6-MPS, T8-MPS T8-DPS

B&D TriTran+ 433.47 / 433.92 /

434.37MHz

CODE SET CADP, CADS, CADP DIAMOND, CAD P

DIAMOND WQ, CAD DIAMOND PD, CAD

PRODIGY, CAD ADVANCE, FIRMAMATIC,

SHEDMASTER

B&D TriTran 433.47 / 433.92 /

434.37MHz

CODE SET

or DOOR

CODE

CADP, CADS, CADP DIAMOND, CAD

P DIAMOND WQ, CAD DIAMOND PD,

FIRMAMATIC, SHEDMASTER, SDO3

B&D Billion Code 433.92MHz CODE SET CAD4, CAD5, CADP, CADR, FAM4, FAM5,

FAMR, EASYLIFTER 4, EASYLIFTER 5

EASYLIFTER R, CAD P DIAMOND, CAD P

DIAMOND WQ, CAD P DIAMOND PD

Boss Fixed 433.92MHz RADIO

SET

RD 11, BOL6 (433MHz Variant)

Chamberlain Security +2.0 433.30 / 433.92 /

434.54MHz

LEARN or

“S”

RollerLift, RollerLift Plus, HandyLift Plus 2.0,

HandyLift Deluxe 2.0, HandyLift MyQ,

HandyLift Deluxe, SectionalLift,

SectionalLift Plus, PowerLift, PowerLift Plus,

PowerLift MyQ, PowerLift Lite

Chamberlain Security + 433.92MHz LEARN HandyLift, HandyLift Plus, CR550, ML500,

ML700, ML750, MLR500, MLR750

Chamberlain Billion Code 433.92MHz CODE SET Refer to B&D Billion Code compatibility above

Guardian Rolling 433.92MHz RADIO

SET

RD2

HercuLift Rolling 433.92MHz LEARN RDO V6

HomEntry Rolling 433.30 / 433.92 /

434.54MHz

LEARN or

“S”

HE60, HE60R, HERD01, HESDO1

Merlin Security +2.0 433.30 / 433.92 /

434.54MHz

LEARN or

“S”

Commander Essential, Commander Elite,

Commander Extreme, Commander Ultimate,

EntryLift, PowerAce, TiltMaster, CyclonePro,

Commander MyQ, SilentDrive Essential,

SilentDrive ELite, QuietDrive, SilentDrive,

WeatherDrive, SilentDrive Elite MyQ,

OverDrive, WhisperDrive, MJ3800

Merlin Security + 433.92MHz LEARN MR60, MR600, MR800, MR650, MR850,

MR1000, MT60, MT60P, MT600, MT800,

MT1000, MT3850, M230T, CG3800, MJ3800.

MT5580, MT5580P, MRC 950,

Merlin Legacy 433.92MHz LEARN ProLift & PowerLift 430R, 230T (Motors

manufactured after 2001)

MotorLift Security + 433.92MHz LEARN ML500, ML700, ML750, MLR500, MLR750

Steeline Security +2.0 433.30 / 433.92 /

434.54MHz

LEARN or

“S”

ST50EVOB, ST50EVOC, SR60, RD11

Superlift Rolling 433.92MHz CODE SDO 3 DC

Taurean Rolling 433.92MHz RADIO

SET

NOVA 1000

LOCATING THE LEARN BUTTON

NOTE: When programming a Merlin or Chamberlain Security+2.0 opener

follow the below steps:

1. Press & release the LEARN button on the opener.

2. Press & release the remote button you wish to program. The code has

been learnt and the next press of the remote button should activate the door.

When programming two doors at the one site, we recommend programming

the TOP button first. This is to avoid accidentally operating a

preprogrammed door. Alternatively turn off any preprogrammed doors.

The Bottom Button is the PROGRAMMING button and is the only button

that can commence the programming sequence, irrespective of which button

you choose to control the door.

The operate buttons require a firm press, this is to eliminate accidental

activation due to mishandling the remote.

This remote only operates with 433.92MHz radio control systems.

PROGRAMMING TIPS

Learn Button

Indicator LED

DN UP PS

123

Learn Button

Sectional & Tilt Door Openers

Roller Door Openers

In order to program the Universal Remote, the LEARN button on the

garage door opener must be located. This will need to be activated

during the programming sequence.

The LEARN button may also be labelled, CODE, CODE SET,

DOOR CODE, RADIO SET, ‘S’, or similar.

Refer to your Opener Owner’s Manual for more information.

Here are examples of the LEARN button position

TEST

Test the remote control by pressing the button you programmed to control

the door. If the garage door opener does not activate, repeat the

programming steps, view the programming videos on

chamberlaindiy.com.au/universal or chamberlaindiy.co.nz/universal or

contact Customer Service AU: 1800 638 234 NZ: 0800 653 667

PROGRAMMING THE REMOTE

Start with your garage door closed. Ensure that the door is clear of all

obstructions.

Press and hold the Bottom Button (for

approximately 15 seconds) on the

remote control until the blue LED stays ON

solid, then release the button. (The blue

LED will remain ON for 60 seconds).

Press the LEARN button on your garage door opener for 2-3 seconds,

then release it.

Immediately Press & Release the remote control button you would like

to program. The Blue LED will commence blinking for 12 seconds.

Once the Blue LED changes to solid, immediately Press & Release

the same button on the remote again. The remote will now try to pair

to the opener.

The Blue LED on the remote control will begin to flash once every three

seconds while trying to pair to the opener, (this may take up to 60

seconds). When the door begins moving, immediately (within 3

seconds) press the remote button again.

The coding process is complete and your remote should now be

programmed to the garage door opener.You can repeat this process

using the other remote button to program another garage door opener.

Blue LED

Bottom

Button

In order to program the Universal Remote, the LEARN button on the

garage door opener must be located. Please refere to page 3 as well as

the compatibility table on page 2 for the lean button label used for various

brands.

These are generic instructions for most garage door openers, for

ATA branded openers refer to the instructions on page 5. Read through

all steps before commencing, and become familiar with the control buttons.

Once the programming sequence has commenced its important to

continue from one step to another reasonably quickly. Time between

steps is critical.

This is also a good time to view our Instructional videos on our website.

chamberlaindiy.com.au/universal or chamberlaindiy.co.nz/universal.

Start with your garage door closed. Ensure that the door is clear of all

obstructions

Press and hold the Bottom Button on the remote

control until the blue LED stays ON solid

(approximately 15 seconds), then release the

button. (The blue LED will remain ON for 60

seconds)

Press and Hold the DOOR CODE button on the garage door opener

(Do not release the DOOR CODE button at this point).

Press and Release the remote control button you would like to program.

The Blue LED will commence blinking for 12 seconds.

Once the Blue LED changes to solid, release the DOOR CODE button

immediately and Press and Release the remote button you are

programming.

The Blue LED will begin flashing once every three seconds. Wait until the

door begins moving, and immediately press the remote button again. The

coding process is complete and your remote should now be programmed

to the garage door opener.

You can repeat this process using the other remote button to program

another garage door opener.

ATA BRANDED OPENERS

These programming instructions are for ATA branded garage door openers.

Read through all steps before commencing, and become familiar with the

control buttons. Once the programming sequence has commenced its

important to continue from one step to another reasonably quickly. Time

between some steps is critical.

This is also a good time to view our Instructional videos on our website.

chamberlaindiy.com.au/universal or chamberlaindiy.co.nz/universal.

Blue LED

Bottom

Button

TEST

Test the remote control by pressing the button you programmed to control

the door. If the garage door opener does not activate, repeat the

programming steps, view the programming videos on

chamberlaindiy.com.au/universal or chamberlaindiy.co.nz/universal or

contact Customer Service AU: 1800 638 234 NZ: 0800 653 667

How do I program the other button on the Universal Remote Control?

After pressing the LEARN button on the motor, go through the same

programming method using the other button. This process will not over

write the first button. The initial 15 second press to put the remote into

learn mode must be performed using the bottom button.

How do I erase previous codes and start fresh?

Codes cannot be erased, only overwritten. A newly programmed code

will take the place of a previous code.

The remote control is not working, the LED is not illuminating.

The LED is also a power indicator, pressing a button on the remote should

cause the LED to illuminate. If the LED does not illuminate after you press

the button, replace the battery using a CR2032 battery.

How can I stop one button from operating two doors?

If one remote control button is operating two doors, you must clear the

memory of the garage door opener that you do not want the button to

activate.

Where is the LEARN button located on my opener?

The LEARN button can either be found on the garage door opener or on an

external receiver. To locate the receiver look for an antenna, some receivers

will require a cover be removed to gain access to the LEARN button.

The LEARN button is often a different colour to the other buttons, and may

be labelled as CODE, CODE SET, DOOR CODE, RADIO SET, “S” or similar.

Refer to your garage door opener manual for information on its location.

Is my garage door opener compatible with the Universal Remote

Control?

Check the compatibility table located on page 2 or for the most up to date

table visit chamberlaindiy.com.au/universal or chamberlaindiy.co.nz/universal.

The Universal remote operates on 433.92MHz systems only.

If I change the battery in the remote control, will I have to reprogram it?

The remote control should retain its memory. If it does not, you will need to

reprogram it.

FREQUENTLY ASKED QUESTIONS

Chamberlain Australia Pty Limited / Chamberlain New Zealand

(Chamberlain), warrants to the original consumer purchaser of this product

that it is free from defect in materials and/or workmanship for a period of 1

year from the date of purchase.

The benefits given to you under this Chamberlain Limited Warranty are in

addition to any rights and remedies that you may have under Australian or

New Zealand consumer protection laws. Our goods come with guarantees

that cannot be excluded under the Australian Consumer Law, or New

Zealand Consumer Guarantees Act 1993.

You are entitled to a replacement or refund for a major failure and for

compensation for any other reasonably foreseeable loss or damage. You are

also entitled to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major failure.

Customer Service:

Australia : 1800 638 234

New Zealand : 0800 653 667

All trade names used herein are trademarks of respective manufacturers listed.

114-5491-000

ONE YEAR LIMITED WARANTY

Table des matières

Autres manuels Chamberlain Télécommande

Chamberlain

Chamberlain LiftMaster 333LM Manuel utilisateur

Chamberlain

Chamberlain CPTKX Manuel utilisateur

Chamberlain

Chamberlain 893LM Manuel utilisateur

Chamberlain

Chamberlain Security+ 963CD Manuel utilisateur

Chamberlain

Chamberlain 891LM Manuel utilisateur

Chamberlain

Chamberlain PASSPORT CPT4 Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional 98685E Manuel utilisateur

Chamberlain

Chamberlain 953C Manuel utilisateur

Chamberlain

Chamberlain LiftMaster 81LM Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Security+ 973TB Manuel utilisateur

Chamberlain

Chamberlain LiftMaster Professional 995LM Manuel utilisateur

Chamberlain

Chamberlain CPTKx Manuel utilisateur

Chamberlain

Chamberlain 61LMC Manuel utilisateur

Chamberlain

Chamberlain 753CB Manuel utilisateur

Chamberlain

Chamberlain 412HMC Manuel utilisateur

Chamberlain

Chamberlain 972MOM Moore-o-Matic Manuel utilisateur

Chamberlain

Chamberlain 850 Series Manuel utilisateur

Chamberlain

Chamberlain TX4REV-F Manuel utilisateur

Chamberlain

Chamberlain 333LM Manuel utilisateur

Chamberlain

Chamberlain 956CD Manuel utilisateur

Chamberlain

Chamberlain 374UT Manuel utilisateur

Chamberlain

Chamberlain CPT4 Manuel utilisateur

Chamberlain

Chamberlain KLIK3U Manuel utilisateur

Chamberlain

Chamberlain KLIK3C-BL Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation