CDA EVS90BL Guide de démarrage rapide
www.cda.eu
EVS90BL
Ceiling extractor
Installation, use and maintenance
2
Contents:
3 Important
5 Important information
6 Using your extractor
8 Care and maintenance
9 Removing the grease filters
10 - 14 Installation
10 Installation preparation - height
11 Cut-out information
12 Fitting the extractor
13 Fitting the motor group
14 Ducting
15 Mains electricity connection
16 Electrical information
16 Troubleshooting
19 Energy Eciency Information
3
Important
The CDA Group Ltd cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note that
CDA reserve the right to invalidate the guarantee supplied with this
product following incorrect installation or misuse of the appliance or
use in a commercial environment.
This appliance is not designed to be used by people (including
children) with reduced physical, sensorial or mental capacity, or
who lack experience or knowledge about it, unless they have had
supervision or instructions on how to use the appliance by someone
who is responsible for their safety.
Under no circumstances, except for instructions laid out in this manual,
should any external covers be removed for servicing or maintenance
except by suitably qualified personnel.
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault with
your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
4
EU Declarations of Conformity:
This appliance has been manufactured to the strictest standards and
complies with all applicable legislation, including Gas safety, Electrical
safety (LVD) and Electromagnetic interference compatibility (EMC).
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2012/19/EU.
At the end of its working life, the product must be taken to a special
local authority waste collection centre or to a dealer providing
appliance recycling services.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health. It also
enables the constituent materials to be recovered, saving both energy
and resources. As a reminder of the need to dispose of household
appliances separately, the product is marked with a crossed-out
wheeled dustbin.
5
IMPORTANT:
• Under no circumstances should the extractor be
connected to any gas ventilation system, flue system or
hot air ducting system.
• Do not vent the extractor into an attic or loft space.
• Only house the extractor in rooms with adequate
ventilation. Remember that the extractor is powerful and
whatever air is extracted needs to be replaced.
• Do not tile the extractor in. It should be removable for
service or maintenance.
• Do not use silicone sealant to secure the hood to the wall.
• You must be able to isolate the extractor from the mains
electrical supply after installation.
• This extractor has been designed to be used in a room
with a volume of less than 36m.
• Steam cleaners must not be used when cleaning this
appliance.
• The performance of your extractor will vary depending
on a number of factors. These include: type of extraction,
length of ducting, room volume, ventilation available and
cleanliness of the filters.
• The extractor, when extracting air, could generate a
negative pressure in the room which can’t exceed 0.04
mbar. Ensure that there are air intakes allowing a constant
flow of fresh air within the room in which the extractor is
installed. Ventilation for gas fuelled appliances must be as
per regulations in force.
6
Using your extractor
For best performance, you should switch on the extractor 15 minutes
before starting to cook and leave it to run for approximately 15
minutes after the end of cooking (you can use the timer function for
this).
1 - On/o button
2 - Speed increase button
3 - Speed decrease button
4 - Light button
Switching the extractor on/o and setting the speed level
- Press the on/o button. The appliance will switch on at speed level 1.
- To increase the speed level touch the speed increase button. Red
LED indicators will illuminate according to the set speed.
- To reduce the speed level touch the speed decrease button.
- To switch the extractor o, touch the on/o button.
Extractor lights
- To switch the lights on and o, press button 4 on the remote control.
Please note: The lights are not intended to provide downlight
illumination.
Fig. 1
1
2
3
4
7
Timer
The extractor is equipped with a timer that allows the extractor to run
for 15 minutes before switching o automatically.
- To activate the timer, set the desired speed and then press and
hold the speed decrease button (3) for approximately two seconds.
The LED indicator for the speed on the extractor body will flash to
confirm the timer is active.
- To cancel the timer, press either the speed increase button, speed
decrease button or the on/o button.
Please note: The timer can be activated on any speed.
8
Care and maintenance
IMPORTANT: DO NOT PERFORM MAINTENANCE OR ATTEMPT
TO CLEAN THE EXTRACTOR WITHOUT FIRST SWITCHING OFF
THE ELECTRICITY SUPPLY. ALWAYS WEAR ADEQUATE PPE
(PERSONAL PROTECTIVE EQUIPMENT) FOR THE TASK AT HAND.
Cleaning
You should use a non-abrasive cleaner. Any abrasive cleaner
(including Cif) will scratch the surface and could erase the control
panel markings.
You can clean your extractor eectively by using a dilute solution of
water and mild detergent and drying to a shine with a clean cloth.
IMPORTANT:
Always protect surfaces immediately beneath the extractor (such
as a hob) with clean, dry towels or similar cushioning items before
carrying out any cleaning or maintenance in case of falling parts/
items.
Cleaning the grease filters
The grease filters should be kept clean to minimise the risk of fire.
At least once a month you should remove and clean the grease
filters with hot soapy water. You can also wash the grease filters in
a dishwasher, ensuring that you place them in an upright position to
prevent damage from other items in the dishwasher. After rinsing and
drying, replace the filters. Please note that washing the filters in a
dishwasher can lead to discolouration. This is not a fault.
9
To remove the grease filters follow these steps:
1. Open the cover panel by pulling down on the LED indicator side.
The panel will lower as far as the hydraulic arms permit.
2. Pull down the handle on each grease filter. It will release at the
handle side. Then, lower the grease filter to remove it completely.
Please note: Releasing the grease filters, when the extractor is
installed, could cause them to fall. Take care and ensure you remove
them safely. Protect any surfaces below accordingly.
To replace the grease filters, repeat the above steps in reverse.
This appliance is fitted with energy saving LED lighting that has a
considerably longer life expectancy than traditional filament bulbs.
These are not user-replaceable. In the unlikely event of a failure
please contact CDA Customer Care using the details on page 17.
The lighting is designed for aesthetic purposes and not for general
room, nor down-light, illumination. Extended use of the lights can
reduce their life span.
10
Installation preparation
When installing this product we recommend you seek the help of
at least two other individuals. This product may have some sharp
edges. Please take care and wear adequate PPE (Personal Protective
Equipment) when handling.
Installation preparation - height
IMPORTANT:
When the extractor is to be installed above a CDA electric hob, the
minimum distance between the hob and the downwards-facing side
of the extractor must exceed 650mm.
When the extractor is to be installed above a CDA gas hob, the
minimum distance between the hob and the downwards-facing side
of the extractor must exceed 650mm.
If the instructions provided with your gas hob state that the
required distance between the hob and extractor must be greater
than our measurement, then that is the distance that should be
observed; this is a legal requirement and may lead to your hob
being disconnected from the gas supply and the installation being
reported under RIDDOR (the height should be measured from the
top of the burners).
IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH A GAS
HOB, THE MINIMUM DISTANCE BETWEEN THE HOB AND
EXTRACTOR MUST BE AT LEAST 760mm. The width of a hob must
not be greater than the width of the extractor installed above it.
Table des matières
Autres manuels CDA hotte de ventilation
CDA
CDA edd61 Instructions d'utilisation
CDA
CDA ECP Series Guide de démarrage rapide
CDA
CDA EVPK9 Manuel de référence
CDA
CDA 3S10BL Guide de démarrage rapide
CDA
CDA CIN6 Manuel de référence
CDA
CDA EVPK90 Fiche technique
CDA
CDA CHX10 Manuel utilisateur
CDA
CDA EVQ71 Guide de démarrage rapide
CDA
CDA 3Z9 Manuel de référence
CDA
CDA ECPK9 Manuel de référence
CDA
CDA CPXI9 Manuel de référence
CDA
CDA 3Q9 Manuel de référence
CDA
CDA CCA5/7 Manuel de référence
CDA
CDA 3Q9 Manuel utilisateur
CDA
CDA 3D9BL Manuel de référence
CDA
CDA EVPC91 Guide de démarrage rapide
CDA
CDA EVC41SS Manuel utilisateur
CDA
CDA CTE6 Manuel utilisateur
CDA
CDA ECN6 Manuel utilisateur
CDA
CDA EDD9BL Manuel de référence
