CAS PD-II Manuel utilisateur

Autres manuels pour PD-II

5

Table des matières

Autres manuels CAS Échelle

CAS

CAS BF-1255B Manuel utilisateur

CAS

CAS LP-1000N Series Manuel utilisateur

CAS

CAS CL-3000 Series Manuel utilisateur

CAS

CAS CT100 Series Manuel utilisateur

CAS

CAS NC-I Manuel utilisateur

CAS

CAS SW-1S Series Manuel utilisateur

CAS

CAS PR-II Series Manuel utilisateur

CAS

CAS LDT Manuel utilisateur

CAS

CAS CBL Series Manuel utilisateur

CAS

CAS SC Series Manuel utilisateur

CAS

CAS CL3500 Series Manuel utilisateur

CAS

CAS SW-1S Series Manuel utilisateur

CAS

CAS PD-2 Manuel utilisateur

CAS

CAS BW-6 Manuel utilisateur

CAS

CAS SW-2 Manuel utilisateur

CAS

CAS HS-1 Manuel utilisateur

CAS

CAS 25AC Manuel utilisateur

CAS

CAS SW-II Series Manuel utilisateur

CAS

CAS SW-1S Series Manuel utilisateur

CAS

CAS CL8000 Series Manuel utilisateur

CAS

CAS CL5000J Series Manuel utilisateur

CAS

CAS NC-100 Manuel utilisateur

CAS

CAS CI-1580A Manuel utilisateur

CAS

CAS FW500-E Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur

09/10/09CAS (USA) Corporation 99 Murray Hill Parkway East Rutherford, NJ 07073 PD-II

PROGRAMMING LBS/OZ FOR PD-II CAL MODE OPTIONS

1. Make sure that the scale is off. Remove the platter. Remove the calibration bolts and plate

located on the top front of the scale.

2. After removing the calibration bolts and plate you will see a white micro switch at the bottom of

the hole. Press and hold down the micro switch and turn on the scale.

3. The display will read “CAL” → “Ver XXX “→ “C-0 “. Release the micro-switch. Press the [ # ]

key until the display shows “C-4 “. Replace the platter. ( “ # “ is to increase and “lb/oz“is to

decrease the value )

4. Press the [ ZERO ] key and display should read “C41 XX “. Press [ ZERO ] to go to the next

step “ C42 XX “ → “ C43 XX “ → “C44 XX “ → “ C45 XX “ → “ C46 XX “.

5. Depending on the capacity and function, enter the value “XX “step by step. Press “# “to move

the digit and “* or lb/oz “to change the value. ( see chart below)

6. Note: For the setting “C42” for all capacities single range is “38” and dual range is what is in the

chart below.

7. The settings for the capacity and single/dual range must follow what is on the serial number plate

or else the scale will not be NTEP or legal for trade subject to a fine by Weights and Measures.

15lb/300oz

30lb/600oz

60lb/1000oz

150lb/2000oz

C41

C8

C8

C8

C8

C42

1A

3A

4A

62

C43

00

00

00

00

C44

80

80

80

80

C45

00

00

00

00

C46

00

00

00

00

8. Press the [ ZERO ] key. Display shows “C4 End “then “C-4 “.

9. Press “* or lb/oz “until the display shows “C-0 “.

C41

C44

What the scale does

C8

80

Starts up in lb and can be switched to oz

d0

80

Starts up in oz and can be switched to lb

C8

00

Starts up in lb and will not switch to oz

D0

00

Starts up in oz and will not switch to lb

10. Press the [ ZERO ] key and scale will do its count up test cycle and the go to “0 “which is

back to normal mode

* Make sure to calibrate the scale in lbs or kg before using.

CHANGING TYPE SETTINGS

1. Make sure that power is OFF. While pressing “# “key, then turn on the power. Display will show

“EcrSEt “. Then current ECR type is shown on the display as “tYPE-2 “.

2. If you select ERC type 5, press the “# “key until the display shows it.

3. To save the current type, press the ZERO Key. Display will go back to “0 “.