Caple AS610BK Manuel utilisateur

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Caple hotte de ventilation

Caple

Caple MOT901 Manuel utilisateur

Caple

Caple INCH Manuel de la liste des pièces

Caple

Caple CGC710BK Manuel

Caple

Caple Tela TEL900 Manuel utilisateur

Caple

Caple CSBCURVE605 Manuel utilisateur

Caple

Caple DD903BK Manuel utilisateur

Caple

Caple SLF4 Manuel technique

Caple

Caple CGI910 Manuel utilisateur

Caple

Caple DD921BK Manuel utilisateur

Caple

Caple BUCHB Manuel utilisateur

Caple

Caple CGC910BK Manuel utilisateur

Caple

Caple Ceramica CR700 Manuel utilisateur

Caple

Caple DD521BK Manuel utilisateur

Caple

Caple CCH601BK Manuel utilisateur

Caple

Caple BXI1050SS Manuel utilisateur

Caple

Caple BXC600SS Manuel utilisateur

Caple

Caple FSCHW6 Manuel utilisateur

Caple

Caple BU520 Manuel utilisateur

Caple

Caple SP610 Manuel utilisateur

Caple

Caple FSCHSS9 Manuel utilisateur

Caple

Caple Orbit OI363 Manuel utilisateur

Caple

Caple CCH100 Manuel

Caple

Caple ZA800 Manuel utilisateur

Caple

Caple BU525BK Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur

Instruction manual for wall chimney hoods

Model codes: AS610BK / AS910BK

Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk

1. For ease of installation, the light assembly should be fitted using a magnetic

screwdriver before the hood is installed on the wall.

2. The plastic cover is to protect the light assembly in transit. Once the light is

fitted to the hood, the plastic cover is easily removed by slackening the screws

and pulling the cover off.

4. For ease of installation, the light assembly should be fitted using a magnetic

screwdriver before the hood is installed on the wall.

5. The plastic cover is to protect the light assembly in transit. Once the light is

fitted to the hood, the plastic cover is easily removed by slackening the screws

and pulling the cover off.

Installing the Ductwork

1. Plan where the ductwork will run between the hood and the outside. The

hoods exhaust vertically but can be ducted to the rear behind the chimney

duct through an outside wall or vertically up through the ceiling to the

roof. A short straight duct run will produce the most air flow. Length and

elbows will reduce the efficiency of the blower.

2. Install a roof or wall cap. Connect a 6 round metal duct to the cap and

work backwards toward the hood. Ensure joints are completely sealed

with duct tape.

Fixing to the Wall

1. Before mounting the hood, plug in and test all functions for correct operation.

2. Remove the filters from the bottom of the hood to pre vent damage during the installation.

3. With assistance, hold the hood temporary in position ensuring the bottom is above the minimum clearance for

the cooking surface. Mark on the wall the holes for the two mounting screws.

4. Drill the holes and install the mounting bracket (1) . Use the appropriate screws and screw anchors for your

wall type (e.g. reinforced concrete, drywall, etc.). If necessary, prepare back wall with cross framing for secure

installation.

5. Mount the hood onto the bracket (2).

Connect a 6 aluminum duct tube (not included) to the exhaust piece using duct tape on all seals. (C)

7.

to roof cap

to wall cap

hood

decorative

chimney duct

38

39

40

Mounting bracket

Hook

1

2

mushroom tapping screw

3

6. Install two mushroom tapping screw into the wall.

Installing Guideline

Wall Mounted-Duct-out

1200~1700mm

650~700mm

Note:The above installation guideline for references only , please contact your local dealer

for a installation service.

Fixing the Decorative Chimney

Flu

1

2

3

.

.

.

Carefully losen but do not separate the telescopic chim ney duct pieces.

Arrange the electrical power supply within the dimen sions of the

decorative chimney duct.

Adjust the width of the support bracket to match the upper duct. Fix it

to the ceiling using the screws (B) so that it is centered in line with your

hood and at a distance from the ceiling indicated.

C

1. Separate lamp cover and left bracket by unscrewing.

2. Install right bracket to the cooker hood, then tighten the screws.

3. Connect two cables.

4. Re-Install left bracket and tighten the screws.