Campbell 05103 Manuel utilisateur

05103, 05106, and 05305

R.M. Young Wind Monitors

Revision: 8/07

Campbell Scientific, Inc.

Warranty and Assistance

The 05103, 05106, and 05305 R.M. YOUNG WIND MONITORS are

warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in

materials and workmanship under normal use and service for twelve (12)

months from date of shipment unless specified otherwise. Batteries have no

warranty. CAMPBELL SCIENTIFIC, INC.'s obligation under this warranty is

limited to repairing or replacing (at CAMPBELL SCIENTIFIC, INC.'s option)

defective products. The customer shall assume all costs of removing,

reinstalling, and shipping defective products to CAMPBELL SCIENTIFIC,

INC. CAMPBELL SCIENTIFIC, INC. will return such products by surface

carrier prepaid. This warranty shall not apply to any CAMPBELL

SCIENTIFIC, INC. products which have been subjected to modification,

misuse, neglect, accidents of nature, or shipping damage. This warranty is in

lieu of all other warranties, expressed or implied, including warranties of

merchantability or fitness for a particular purpose. CAMPBELL SCIENTIFIC,

INC. is not liable for special, indirect, incidental, or consequential damages.

Products may not be returned without prior authorization. The following

contact information is for US and International customers residing in countries

served by Campbell Scientific, Inc. directly. Affiliate companies handle

repairs for customers within their territories. Please visit

www.campbellsci.com to determine which Campbell Scientific company

serves your country. To obtain a Returned Materials Authorization (RMA),

contact CAMPBELL SCIENTIFIC, INC., phone (435) 753-2342. After an

applications engineer determines the nature of the problem, an RMA number

will be issued. Please write this number clearly on the outside of the shipping

container. CAMPBELL SCIENTIFIC's shipping address is:

CAMPBELL SCIENTIFIC, INC.

RMA#_____

815 West 1800 North

Logan, Utah 84321-1784

CAMPBELL SCIENTIFIC, INC. does not accept collect calls.

05103, 05106, 05305 Table of Contents

PDF viewers note: These page numbers refer to the printed version of this document. Use

the Adobe Acrobat® bookmarks tab for links to specific sections.

1. General Description.....................................................1

2. Specifications ..............................................................1

3. Installation....................................................................3

3.1 Siting.........................................................................................................3

3.2 Assembly and Mounting...........................................................................3

4. Wiring............................................................................5

5. Example Programs......................................................6

5.1 Wind Speed ..............................................................................................6

5.2 Wind Direction.........................................................................................6

5.3 Wind Vector Processing Instruction.........................................................7

5.4 Example Programs....................................................................................7

5.4.1 CR1000 Example Program .............................................................8

5.4.2 CR10X Example Program ..............................................................8

5.5 Long Lead Lengths...................................................................................9

6. Sensor Maintenance..................................................10

7. Troubleshooting ........................................................10

7.1 Wind Direction.......................................................................................10

7.2 Wind Speed ............................................................................................11

8. References .................................................................11

Appendices

A. Wind Direction Sensor Orientation........................A-1

A.1 Determining Truth North and Sensor Orientation .............................. A-1

05103, 05106, 05305 Table of Contents

B. Wind Direction Measurement Theory....................B-1

B.1 BRHalf Instruction.............................................................................. B-1

B.2 EX-DEL-SE (P4) Instruction .............................................................. B-1

Figures

3-1. Wind Monitor Mounted to the 019ALU Crossarm ................................ 4

3-2. Wind Monitor Mounted to a CM200 Series Crossarm

with PN 17953 Nu-Rail....................................................................... 4

3-3. Wind Monitor Mounted to a CM200 Series Crossarm

with CM220 Right Angle Mounting Kit............................................. 5

A-1. Magnetic Declination for the Contiguous United States ...................A-2

A-2. Declination Angles East of True North are Subtracted From 0 to

Get True North................................................................................A-2

A-3. Declination Angles West of True North are Added to 0 to

Get True North................................................................................A-3

B-1. 05103 Potentiometer in a Half Bridge Circuit ................................... B-1

Tables

1-1. Recommended Lead Lengths ................................................................. 1

4-1. Connections to Campbell Scientific Dataloggers................................... 5

5-1. Wind Speed Multiplier (with Configuration Code 21)........................... 6

5-2. Parameters for Wind Direction............................................................... 7

5-3. Wiring for Example Programs................................................................ 7

05103, 05106, and 05305 R.M. Young

Wind Monitors

1. General Description

The 05103, 05106, and 05305 Wind Monitor sensors are used to measure

horizontal wind speed and direction. The 05305 is a high performance version

of the 05103 designed to meet PSD specifications for air quality applications.

The 05106 is recommended for marine applications.

Wind speed is measured with a helicoid-shaped, four-blade propeller. Rotation

of the propeller produces an AC sine wave signal with frequency proportional

to wind speed.

Vane position is transmitted by a 10K ohm potentiometer. With a precision

excitation voltage applied, the output voltage is proportional to wind direction.

The R.M. Young Instruction Manual includes additional information on the

operating principles, installation and maintenance of the sensor.

Lead length for the Wind Monitor is specified when the sensor is ordered.

Table 1-1 gives the recommended lead length for mounting the sensor at the

top of the tripod/tower with a 019ALU or CM200 series crossarm.

TABLE 1-1. Recommended Lead Lengths

CM6 CM10 CM110 CM115 CM120 UT10 UT20 UT30

10’ 13’ 13’ 19’ 24’ 13’ 24’ 34’

The 05103 / 05106 / 05305 ships with:

(1) Allen wrench from mfg

(1) Bearing spacer from mfg

(1) Calibration Sheet

(1) Instruction Manual

(1) 3659 Mounting pipe

2. Specifications

05103 and 05106 05305

Wind Speed

Range: 0-134 mph (0-60 m s-1) 0-90 mph (0-40 m s-1)

Accuracy: ±0.6 mph (±0.3 m s-1) ±0.4 mph (±0.2 m s-1)

Starting threshold: 2.2 mph (1.0 m s-1) 05103;

2.4 mph (1.1 m s-1) 05106 0.9 mph (0.4 m s-1)

Gust survival: 220 mph (100 m s-1) 100 mph (45 m s-1)

Distance constant

(63% recovery):

8.9 ft (2.7 m)

6.9 ft (2.1 m)

05103, 05106, and 05305 R.M. Young Wind Monitors

05103 and 05106 05305

Output: ac voltage (3 pulses per

revolution). 1800 rpm

(90 Hz) = 19.7 mph

(8.8 m s-1)

ac voltage (3 pulses per

revolution) 1800 rpm

(90 Hz) = 20.6 mph

(9.2 m s-1)

Wind Direction

Range: 0-360° mechanical,

355° electrical (5° open) Same

Accuracy: ±3° ±3°

Starting threshold

at 10° displacement:

2.2 mph (1.1 m s-1)

1.0 mph (0.5 m s-1)

Delay distance

(50% recovery):

4.3 ft (1.3 m)

3.9 ft (1.2 m)

Damping ratio: 0.25 0.45

Damped natural

wavelength:

24.3 ft (7.4 m)

16.1 ft (4.9 m)

Undamped natural

wavelength:

23.6 ft (7.2 m)

14.4 ft (4.4 m)

Output: Analog dc voltage from

potentiometer – resistance

10 kΩ, linearity 0.25%,

life expectancy 50 million

revolutions.

Same

Power Switched excitation

voltage supplied

by the datalogger.

Same

Physical

Operating

Temperature

-50° to +50°C, assuming

non-riming conditions

-50° to +50°C, assuming

non-riming conditions

Dimensions

Overall: 14.6” H x 21.7” L

(37 cm x 55 cm) 15.0” H x 25.6“ L

(38 cm x 65 cm)

Main housing

Diameter:

2.0“ (5 cm)

Same

Propeller Diameter: 7.1” (18 cm) 7.9” (20 cm)

Mounting Pipe: 1.34” (34 mm) OD;

standard 1.0” IPS

schedule 40

Same

Weight (shipping

approx.)

3.2 lbs (5.5 lbs);

1.5 kg (2.3 kg)

2.5 lbs (5.5 lbs);

1.1 kg (2.3 kg)

Manufactured by RM Young (Traverse City, MI) and cabled by Campbell

Scientific for use with our dataloggers.

05103, 05106, and 05305 R.M. Young Wind Monitors

The black outer jacket of the cable is Santoprene® rubber. This

compound was chosen for its resistance to temperature extremes,

moisture, and UV degradation. However, this jacket will

support combustion in air. It is rated as slow burning when

tested according to U.L. 94 H.B. and will pass FMVSS302.

Local fire codes may preclude its use inside buildings.

NOTE

3. Installation

3.1 Siting

Locate wind sensors away from obstructions (e.g. trees and building). As a

general rule of thumb there should be a horizontal distance of at least ten times

the height of the obstruction between the windset and the obstruction. If it is

necessary to mount the sensors on the roof of a building, the height of the

sensors above the roof, should be at least 1.5 times the height of the building.

See Section 9 for a list of references that discuss siting wind speed and

direction sensors.

3.2 Assembly and Mounting

Tools Required:

•5/64” Allen wrench

•1/2” open end wrench

•compass and declination angle for the site (see Appendix A)

•small screw driver provided with datalogger

•UV resistant cable ties

•small pair of diagonal-cutting pliers

•6 - 10” torpedo level

Install the propeller to the propeller shaft using the nut provided with the

sensor.

The 05103 mounts to a standard 1” IPS schedule 40 pipe (1.31” O.D.). A 12”

long mounting pipe ships with the 03001 for attaching the sensor to a 019ALU

(Figure 3-1), or CM200 series crossarm with the CM220 or PN 1049 (Figures

3-2 and 3-3). The 05103 can also be mounted to a CM110 series tripod mast

with the CM216 Mast Mounting Kit.

Mount the 019ALU or CM200 series crossarm to the tripod or tower. Orient

the crossarm North-South, with the 1” Nu-Rail or CM220 on the North end.

Appendix A contains detailed information on determining true north using a

compass and the magnetic declination for the site.

Secure the mounting pipe to the 019ALU or CM220. Place the orientation

ring, followed by the 05103 on the mounting pipe. Orient the junction box to

the south, and tighten the band clamps on the orientation ring and mounting

post. Final sensor orientation is done after the datalogger has been

programmed to measure wind direction as described in Appendix A.

Route the sensor cable along the underside of the crossarm to the tower/tripod

mast, and to the instrument enclosure. Secure the sensor cable to the crossarm

and mast using cable ties.

05103, 05106, and 05305 R.M. Young Wind Monitors

YOUNG

Wind Monitor

Mounting Pipe

(supplied with sensor)

019ALU Crossarm

FIGURE 3-1. Wind Monitor Mounted to the 019ALU Crossarm

YOUNG

Wind Monitor

PN 17953 Nu-Rail

CM200 Series Crossarm Mounting Pipe

(supplied with sensor)

FIGURE 3-2. Wind Monitor Mounted to a CM200 Series Crossarm

with PN 17953 Nu-Rail

05103, 05106, and 05305 R.M. Young Wind Monitors

Wind Monitor

Mounting Pipe

(supplied with sensor)

CM220

CM200 Series Crossarm

FIGURE 3-3. Wind Monitor Mounted to a CM200 Series Crossarm

with CM220 Right Angle Mounting Kit

4. Wiring

Connections to Campbell Scientific dataloggers are given in Table 4-1. When

Short Cut for Windows software is used to create the datalogger program, the

sensor should be wired to the channels shown in the wiring diagram created by

Short Cut.

TABLE 4-1. Connections to Campbell Scientific Dataloggers

Color

Description

CR800

CR5000

CR3000

CR1000

CR510

CR500

CR10(X)

21X,

CR7

CR23X

CR200

Red Wind Spd.

Signal Pulse Pulse Pulse P_LL

Black Wind Spd.

Reference

Green Wind Dir. Signal SE Analog SE

Analog SE

Analog SE Analog

Blue Wind Dir.

Excitation Excitation Excitation Excitation Excitation

White Wind Dir.

Reference

Clear Shield wire

05103, 05106, and 05305 R.M. Young Wind Monitors

5. Example Programs

This section is for users who write their own programs. A datalogger program

to measure this sensor can be created using Campbell Scientific’s Short Cut

Program Builder software. You do not need to read this section to use Short

Cut.

5.1 Wind Speed

Wind speed is measured with the Pulse Count instruction, and with the low

level AC configuration. For dataloggers programmed with Edlog, specify

configuration code 21 to output frequency in Hertz.

The expression for wind speed (U) is:

U = MX + B

where

M = multiplier

X = number of pulses per second (Hertz)

B = offset

Table 5-1 lists the multipliers to obtain miles/hour or meters/second when the

Pulse Count instruction is configured to output Hz (configuration code 21).

The helicoid propeller has a calibration that passes through zero, so the offset

is zero (Gill, 1973; Baynton, 1976).

TABLE 5-1. Wind Speed Multiplier

(With Configuration Code 21*)

Model Miles/Hour Output Meters/Second Output

05103 or 05106 0.2192 0.0980

05305 0.2290 0.1024

*When configuration code 11 is used, the multiplier above is

divided by the execution interval in seconds.

5.2 Wind Direction

The wind vane is coupled to a 10K potentiometer, which has a 5 degree

electrical dead band between 355 and 360 degrees.

The EX-DEL_SE measurement instruction is used for dataloggers that are

programmed with Edlog (e.g. CR10X, CR23X) and the CR200. The

measurement result is mV; the multiplier to convert mV to degrees is

355deg/excitation mV.

The BRHalf measurement instruction is used for dataloggers that are

programmed with CRBasic (e.g. CR1000, CR3000). The multiplier to convert

the measurement result (mV/excitation mV) to degrees is 355.

Autres manuels pour 05103

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Campbell Instrument de mesure

Campbell

Campbell CS106 Manuel utilisateur

Campbell

Campbell CMP6-L Manuel utilisateur

Campbell

Campbell CMP3 Manuel utilisateur

Campbell

Campbell 109 Manuel utilisateur

Campbell

Campbell CSAT3B Manuel utilisateur

Campbell

Campbell CS805 Manuel utilisateur

Campbell

Campbell WindSonic Manuel utilisateur

Campbell

Campbell CS320 Manuel utilisateur

Campbell

Campbell LI200R Manuel utilisateur

Campbell

Campbell TEMPERATURE PROBE 109SS Manuel utilisateur

Campbell

Campbell CS616 Manuel utilisateur

Campbell

Campbell TDR100 Manuel utilisateur

Campbell

Campbell IRGASON Manuel utilisateur

Campbell

Campbell CR23X Manuel utilisateur

Campbell

Campbell CS106 Manuel utilisateur

Campbell

Campbell OTT ADC Guide de référence

Campbell

Campbell CNR1 Manuel utilisateur

Campbell

Campbell EasyAG SDI-12 Manuel utilisateur

Campbell

Campbell CS300 Manuel utilisateur

Campbell

Campbell DOT600 Manuel utilisateur

Campbell

Campbell OXYGUARD TYPE III CS512 Manuel utilisateur

Campbell

Campbell HMP60 Manuel utilisateur

Campbell

Campbell CR10TCR Manuel utilisateur

Campbell

Campbell SoilVUE 10 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur