CAME KIT AGT V + LITHOS Manuel utilisateur
AGTLVKIT
AGT V
M2M1
+–
VAS/101
LITHOS
EN
E
ngl
i
sh
FA01429-EN
INSTALLATION MANUAL
KIT AGT V + LITHOS
AGT V
M2M1
+–
VAS/101
LITHOS
Page 2 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
CONTENTS OF THE KIT
General precautions
• Read the instructions carefully before beginning the installation and carry out the procedures as specified by the manufacturer.
• The product must be installed, programmed, commissioned and serviced by qualified technicians, correctly trained with regard to
respecting the regulations in force, including implementing accident-prevention measures.
• Before carrying out any cleaning or maintenance operation, disconnect the power supply.
• The equipment must only be used for the purpose for which it was designed.
• The manufacturer declines all liability for any damage as a result of improper, incorrect or unreasonable use.
–
+
AL
B
M1
CL.RES
M/S
CL.RES
XDV/304
CL.RES CL.RES
M/S MASTER SLAVEM/S
Fam. Rossi
Page 3 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
AGT V
Description
Internal video receiver.
Function of terminals and jumpers
Terminal board M1
BBUS-line input
–
+
Landing call
AL Alarm input
Closing resistance (CL.RES)
Master/slave selector (M/S)
Technical data
Type AGT V
Power supply from BUS line (VDC) 15 to 20
Maximum consumption (mA) 175
Consumption in stand-by mode (mA) <1
Single LED consumption (mA) 1
Operating temperature (°C)
+5 to +40
IP Rating IP 30
Video standard PAL/NTSC
LCD TFT display (inches) 5
1
2
①
②
Page 4 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Installation
• Unhook the device from the metal support by press-
ing the plastic tab and sliding the device smoothly o
the support .
• Fix the wall support to the round Ø 60 mm recessed
box , to the rectangular box 503 , or to the
Ophera (PHI) recessed box , with the “TOP” arrow
pointing upwards.
• Avoid overtightening the screws.
• Use screws and anchors to make the support more
stable.
• The box must be installed at a suitable height for the
user.
• Once the connections have been made, attach the
video terminal to the metal support .
• To unfasten the unit from the metal support, press the
plastic tab and lift the terminal .
Lb
La
VA/01
XDV/304
L1 L2 L3
MT M MT M MT M
N° Slave
N° Master
N° Slave
Lb
La
Lc
Lithos
XDV/304
VAS/101
N° Master
Page 5 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
VCM/1D VCM/2D UTP/CAT 5 2 x 2.5
mm2
La+Lb ≤100 m – ≤60 m –
L1, L2, L3 – ≤100 m – –
L1+L2+ L3 – ≤300 m – –
La + Lb + L1(L2, L3) ≤150 m
La + Lb + L1 + L2 + L3 ≤600 m
VCM/1D UTP CAT5
No. Master 4321321
No. Slave 4567067
VCM/1D UTP CAT5
No. Master 3211
No. Slave 0373
VCM/1D VCM/2D UTP/CAT 5 2x1mm22 x 2.5 mm2
La+Lb ≤100 m – ≤100 m – –
Lc – – – ≤25 m ≤60 m
La+Lb+Lc ≤100 m
System limits
4 monitors can be switched on simultaneously only in one- or two- family systems with entry panel X1+VA/01.
3sec
... beep!
Page 6 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Configuring melodies
☞Perform each of the following programming-steps, in suc-
cession:
1-Enter programming mode.
Press and hold the button for 3 seconds. A short buzzing
sound and a red flashing LED confirm that you have entered pro-
gramming mode .
2-Programming the melody associated with the call from
the entry panel.
To listen to the melodies in sequence, press .
To select the melody and exit the programming mode, press
.
To select the melody and continue programming, press .
3- Programming the melody associated with a call from the
landing.
To listen to the melodies in sequence, press .
To select the melody and exit the programming mode, press
.
To select the melody and continue programming, press .
4-Programming the number of rings per call.
Press as many times as the number of rings you want (from
1 to 12 rings) .
Three seconds after the key was last pressed, the selected call is
played back with the chosen number of rings.
To exit programming mode, press .
☞To program a call, please see the entry panel manuals.
43,5
45
7,5 57
70
106
A
M2M1
+–
Page 7 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
VAS/101
Technical data
T
yp
e VAS-101
Power supply 230 VAC 50-60 Hz
Max. absorbed current
(mA AC)
200
Dissipated power 10 W max
Rated power 18 VDC 1 A-0.5 A 1’/3’
Size 4 DIN
Storage temperature -25°C + 70°C
Operating temperature 0°C +35°C
IP rating IP 30
Installation
The power supply must always be installed horizontally.
• The device can be installed on DIN rails (EN 50022) on a suit-
able switchboard.
• See figure for dimensions.
NOTE. Ensure there is correct ventilation if the power supply is
installed in a metal case.
Terminal board M1
~Network
~
Terminal board M2
–
+Power supply 18 V DC (*)
(*) The device is electronically protected against
overloads and short circuits.
500 mm
1080 mm
77°
94°
800 mm
500 mm
163,5 mm
43,5 mm
1550 - 1600 mm
Page 8 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
LVC/01
Wall-mounted installation
Use a hex key to unscrew the screws in the front plate and re-
move it (figure ).
Fix the plugs provided and screw in the entry panel (figure )
at the desired height, bearing in mind the position of the video
camera lens (figure ).
Thread the pipe with the system conductors as shown in figure
.
Pull out the plastic terminal cover and make the connections
(figure ).
Once the connections have been made, reinsert the terminal
covers.
For information on fitting accessories, please see the “Button
modules assembly” section.
Program and adjust the entry panel as described in the “Pro-
gramming” section. Fit the front plate (figure ).
Recessed installation
First thread the pipe with the system conductors through one of
the break points (figure , point ). Then wall in the recessed
box at the desired height, bearing in mind the position of the
video camera lens (figure ). When installing the recessed box,
avoid any deformations by using the spacer provided (figure ,
point .
Use a hex key to unscrew the screws in the entry-panel front
plate and remove it (figure ).
Thread the connection cables through the hole (figure ) and
A
B
DPS LTP
LSI LCI
Page 9 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
fix the entry panel to the frame as shown in figure . Pull out
the plastic terminal cover and make the connections (figure ).
Once the connections have been made, reinsert the terminal
covers.
For information on fitting accessories, please see the “Button
modules assembly” section.
Program and adjust the entry panel as described in the “Pro-
gramming” section.
Fit the front plate (figure ).
Accessories
- Single button DPS ,
- Wall cover LTP ,
- Recessed box LSI ,
- Recessed frame LCI .
1
2
M1
BOUT
M2
SW3
PROG
PROG
M2M1
+–
9/6
B
B
–
NO
C
–+
Page 10 - Manual FA01429-EN - 07/2020 - © CAME S.p.A. -The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Assembling the modules
Insert the button module as shown in figure , making sure it is
the right way up (figure ).
Remove the glass and write the names of the users as shown
in figure , paying particular attention to which way round the
glass is inserted (figure ).
Name cards: Size
53x13x0.3 mm
53x33x0.3 mm
Function of terminals
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels CAME Système d'interphone
CAME
CAME BPT THANGRAM Manuel du propriétaire
CAME
CAME 001DC01EARY Manuel utilisateur
CAME
CAME XTS 7IP WH WIFI Manuel utilisateur
CAME
CAME DIR 10 Manuel utilisateur
CAME
CAME 001CS1PLCO Manuel utilisateur
CAME
CAME XTS 7IP WH WIFI Manuel utilisateur
CAME
CAME XTS 7IP WH WIFI Manuel utilisateur
CAME
CAME 001CK0010 Manuel utilisateur
CAME
CAME AGT V Manuel utilisateur
CAME
CAME QBESetUp Manuel du propriétaire
CAME
CAME 001DC011AC Manuel utilisateur
CAME
CAME XVP S Feuille d'instructions
CAME
CAME BPT KIT FREE LVC Manuel utilisateur
CAME
CAME XVP S Manuel utilisateur
CAME
CAME Bpt TARGHA GSM VR1 Manuel utilisateur
CAME
CAME Entrotec Entroview Manuel utilisateur
CAME
CAME PLACO-C Manuel utilisateur
CAME
CAME BPT DVC/01 Manuel du propriétaire
CAME
CAME PLACO-VC Manuel utilisateur
CAME
CAME PLX A Manuel utilisateur
