CAME BPT EVKIT Manuel utilisateur

VA/01

DVC/01

DVC/01 ME

PEV/01

OPALE

INSTALLATION MANUAL

EVKIT

English

FB01044-EN

VIDEO ENTRY KIT

Page 2- Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

General Notes

• Read the instructions carefully before beginning the installation

and carry out the actions as speciﬁed by the manufacturer.

• The installation, programming, commissioning and mainte-

nance of the product must only be carried out by qualiﬁed tech-

nicians, properly trained in compliance with the regulations in

force, including health and safety measures and the disposal of

packaging.

• The installer must ensure that the information for the user,

where there is any, is provided and delivered.

• Before carrying out any cleaning or maintenance operation,

disconnect the devices from the power supply.

• The equipment must only be used for the purpose for which it

was expressly designed.

• The manufacturer declines all liability for any damage as a

result of improper, incorrect or unreasonable use.

The product complies with the applicable reference directives.

Dismantling and disposal. Dispose of the packaging and the

device properly at the end of its life cycle, according to the regu-

lations in force in the country where the product is used. The re-

cyclable components bear the symbol and code for the material.

The data and information provided in this manual are subject to

change at any time without prior notice. Measurements, unless

otherwise indicated, are in millimetres.

PEV/01

Installation

Remove the unit from the metallic support by sliding it after

pressing the plastic button A.

Fasten the metallic support to the round built-in box of Ø 60

mm Bor to the rectangular box 503 CDusing the provided

screws and observing the UP indication .

The recessed box must be ﬁtted at a suitable height in relation

to the user.

Avoid excessive tightening of the screws.

Once the connections have been made, hook the video terminal

to the metal support EF.

Ð +

AL B

M/S

CL.RES

Page 3- Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

To release the unit from the metal support, press the plastic hook

and lift the terminal G.

Technical data

Type PEV

Maximum current draw (mA) 200

Current draw in stand-by mode (mA) < 1

Single LED current draw (mA) 1

Storage temperature (°C) -25 to +70

Video standard PAL/NTSC

LCD TFT colour display (inches) 3.5

Function of terminals

AL Alarm input

–

Doorbell

BBUS line input

CL. RES - Closing resistance

CL.RES CL.RES CL.RES

1 2 3

XDV/304

M/S - Master/Slave selector

MASTER SLAVE

M/S M/S

In case of simultaneous call, the audio/video communication

will be activated on the MASTER extension only.

X 5

beep

X 5

beep

Page 4- Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

1- Going into Programming.

Press button 5 times in 5 secs A.

A short beep conﬁrms that you have entered programming mode.

2- Programming the melody associated with a call from the entry panel.

To listen to the melodies in sequence, press key B.

To select the melody and exit programming, press key C.

To select the melody and continue with programming, press key D.

3- Programming the melody associated with a call from the front door.

To listen to the melodies in sequence, press key E.

To select the melody and exit programming, press key F.

To select the melody and continue with programming, press key G.

4- Programming the number of rings for the call.

Press key Has many times as you want it to ring (from 1 to 6 rings).

Three seconds after the last press of the key the call selected for the cho-

sen number of rings will be played back.

To exit programming, press key I.

☞See the entry panel documentation for call programming.

Setting melodies

☞All the programming stages described below must be carried out in sequence:

OPALEKP

B A

C B

D C

Page 5- Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

OPALE

Wall-mounted installation

Separate the unit body from the frame A.

Fasten the OPALEKP wall-mounting support (optional) to the

recessed box using the screws provided; the support is com-

patible with the following recessed box models: round 60 mm

Ø, 503 rectangular, 506E rectangular, and OPALESI (optional).

To guarantee better stability, fasten the support with the screws

and plugs provided 1. Fasten the frame to the wall-mounting

support using the screws provided, avoiding tightening them too

much 2.Wire up the terminal board and put it back in its com-

partment C. Attach the device to the frame D.

Recessed installation C

Wall in the OPALESI recessed box (optional) ﬂush with the wall,

following the instructions on the mortar guard provided.

Fasten the frame to the recessed box using the screws provided,

avoiding tightening them too much 1.

Wire up the terminal board and put it back in its compartment

B. Attach the device to the frame C.

10mm

OPALEKP

E F

158

138

28.5 30.9

OPALEKP

Page 6- Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

Recessed installation on plasterboard wall D

Hold the box up against the plasterboard wall and mark the 4

reference points for installation 1.

Make 4 holes, 10 mm in diameter, at the reference points. Cut

the plasterboard to make a compartment for the box in the wall

Remove the 2 tabs on the box as shown in the ﬁgure C.

Slot the ﬁxing terminals in the box as shown in the ﬁgure D.

Fit the recessed box in the hole made in the wall E.

Click the bottom of the terminals into place. If the wall is thick-

er than 2 cm, you need to cut the joints holding the two parts

of the terminal together; this will allow you to slide the bottom

part of the terminal into the desired position and then tighten

the screws F.

Fam. Rossi

16-18VDC

Page 7- Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

Terminal board F

+Local power supply

16-18 VDC

–

BBUS line input

+Doorbell

–

AL Alarm input

Closing resistance (CL.RES) G

The jumper should be inserted in the last device in the line only.

Master/Slave selector (SKM) H

If two or more receivers have been conﬁgured to answer the

same call, the preview image of the caller is shown only on the

master device(s).

Power supply source selector (BUS/LOCAL) I

APosition of the jumper with locally powered device

2Position of the jumper with BUS-powered device

Technical data

Type OPALE

Power supply by BUS (VDC) 15-20

Separate X2 power supply (VDC) 16-18

Consumption (mA max) 250

Consumption in stand-by mode (mA)

Single LED consumption (mA)

(call from porter, ringtone excluded) 1

Video standard PAL/NTSC

LCD TFT colour display (inches) 3.5

Protection rating (IP)

Storage temperature (°C) -25 to +70

Operating temperature (°C) 0 to +35

43,5

7,5 57

210

106

64,5

210

145

Page 8- Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

VA/01

Installation

The power supplier must ALWAYS be installed horizontally.

The device can be installed on a DIN rail (EN 50022) in an appro-

priate electric panel or it may be wall-mounted using the protec-

tive terminal covers.

For disassembly, proceed as shown in ﬁgure B-C.

For the overall dimensions see ﬁgure A.

NOTE. Proper ventilation is required if the power supplier is

installed in a metal container.

Technical data

Type VA/01

Power supply [VAC] 230

Max current demand [AAC] 0,35

Max energy dissipation [W] 25

Entry panels nominal power supply [VDC] 18

Entry panels current demand [A] 0,6

Entry panels peak power supply [VDC] 18

Entry panels peak current demand [A] 1,1 <15’’ (*)

Rising cable power supply [VDC] 20

Rising cable current demand [A] 0.8 for 1’

Rising cable current demand [A] 0.2 for 3’

Dimensions [DIN] 12

Storage temperature [°C] -25 ÷ + 70

Operating temperature [°C] 0 ÷ +35

Protection rating [IP] 30

(*) 1.6 A <15’’ with rising cable not connected or connected

separately.

MINI

USB

RS232 PROG

DL2 DL1

RFID

PROG

+12V

BIN1 BIN2 BIN3 BOUT

1BC

Page 9- Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

Functions D

Terminal boards A

~Mains

Morsettiera M1

Aux 1 output Open Collector max 100 mA

+12V Common

Aux 2 output Open Collector max 100 mA

+ Entry panel power supply 18 VDC (*)

–

BIN1 BUS line input from entry panel 1

BIN2 BUS line input from entry panel 2

BIN3 BUS line input from entry panel 3

BOUT Busbar output

(*) The appliance is electronically protected against overloads

and short circuits.

Connectors

A RS232: Reserved for future use

B MINI USB: Connector for programming from a PC

C PROG button (**)

RFID PROG Jumper (**)

RFID

PROG

RFID

PROG

RFID

PROG

Default Code entry Code deletion

LED

Colour Meaning

DL1 (**) Yellow Programming status

DL2 Green USB connected

(**) Refer to the “Programming".

VA/01

VA/01 VA/01

VA/01

VA/01 VA/01

VA/01

VA/01 VA/01 VA/01

VA/01

130+320+500=950 mA <1100 mA 500+130+320+500=1450 mA >1100 mA

500 mA 500 mA 500 mA

320 mA 320 mA

130 mA 130 mA

35+35+35+130+130+35+130+35+35+35=635 mA >600 mA

130 mA 130 mA 130 mA35 mA 35 mA 35 mA 35 mA 35 mA 35 mA 35 mA

35+35+130+130+35+130+35+35=565 mA <600 mA

130 mA 130 mA 130 mA35 mA 35 mA 35 mA 35 mA 35 mA

Page 10 - Manual FB01044-EN - vers. 1- 01/2018- © Came S.p.A. - The contents of this manual may be changed, at any time, and without notice.

Absorption

With entry panel ‘on standby’ With solenoid lock ‘on’ With surveillance camera on

130 mA 130 mA 35 mA 320 mA 500 mA

Autres manuels CAME BPT Système d'interphone

CAME BPT

CAME BPT DDC/08 VR Manuel utilisateur

CAME BPT

CAME BPT PEC IP Manuel utilisateur

CAME BPT

CAME BPT LVC/01 Manuel du propriétaire

CAME BPT

CAME BPT XTS 5IP WH Manuel utilisateur

CAME BPT

CAME BPT XTS 7 WIFI Series Manuel

CAME BPT

CAME BPT XTS 5IP WH Manuel

CAME BPT

CAME BPT THANGRAM Manuel utilisateur

CAME BPT

CAME BPT THANGRAM Manuel du propriétaire

CAME BPT

CAME BPT DC/08 Manuel du propriétaire

CAME BPT

CAME BPT AGATA AUDIO Manuel utilisateur

CAME BPT

CAME BPT DDVC/08 VR Manuel utilisateur

CAME BPT

CAME BPT AGT V200 Manuel utilisateur

CAME BPT

CAME BPT XTS 7 WH WIFI Manuel utilisateur

CAME BPT

CAME BPT FUTURA X1 Manuel utilisateur

CAME BPT

CAME BPT Agata C200 UK Manuel utilisateur

CAME BPT

CAME BPT XTS 5IP WH Manuel

CAME BPT

CAME BPT MTMA/IP Manuel du propriétaire

CAME BPT

CAME BPT PEC Manuel utilisateur

CAME BPT

CAME BPT AGATA AUDIO Manuel utilisateur

CAME BPT

CAME BPT XTS 7IP WH WIFI Manuel

CAME BPT

CAME BPT THANGRAM Feuille d'instructions

CAME BPT

CAME BPT FUTURA X2 Manuel utilisateur

CAME BPT

CAME BPT DC/IP ME Feuille d'instructions

CAME BPT

CAME BPT LVKIT Manuel utilisateur

Manuels Système d'interphone populaires d'autres marques

Bticino

Bticino LINEA 3000 Manuel utilisateur

MSI

MSI MSI-140 Manuel utilisateur

golmar

golmar Stadio Plus Manuel utilisateur

CyberData

CyberData 011211 series Manuel

Vidos

Vidos duo M1021 Manuel utilisateur

Vimar

Vimar ELVOX 7539/E Manuel utilisateur

SSS Siedle

SSS Siedle BTSV 850-03 Manuel utilisateur

Dahua

Dahua VTO Series Manuel utilisateur

Elvox

Elvox 5651 Manuel utilisateur

Videx

Videx VIDEOKIT Series Manuel utilisateur

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuel utilisateur

Viking

Viking E-35-EWP Manuel utilisateur

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuel utilisateur

SSS Siedle

SSS Siedle BFCV 850 Series Manuel utilisateur

GRD

GRD MAX V2 Manuel utilisateur

Alecto

Alecto ADI-250 Manuel utilisateur

Aiphone

Aiphone IE-8MD Manuel utilisateur

Perel

Perel EDB4 Manuel utilisateur