Cabletron Systems 6C105 Manuel utilisateur

6C105 SmartSwitch 6000

Overview and Setup Guide

12345

PS1 PS2

6C405

9032016-04

6C105 Overview and Setup Guide i

NOTICE

Cabletron Systems reserves the right to make changes in speciﬁcations and other information

contained in this document without prior notice. The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FORANY INCIDENTAL,

INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT

NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR

THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN

ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.



Printed in the United States of America

Order Number: 9032016-04 March 1998

Cabletron

Systems

SPECTRUM

, and

LANVIEW

are registered trademarks and

SmartSwitch

and

HubStack

are trademarks of Cabletron Systems, Inc.

All other product names mentioned in this manual may be trademarks or registered trademarks of

their respective companies.

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment.

This equipment uses, generates, and can radiate radio frequency energy and if not installed in

accordance with the operator’s manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause interference in which case the user

will be required to correct the interference at his own expense.

WARNING:

Changes or modiﬁcations made to this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

Only qualiﬁed personnel should perform installation

procedures.

Printed on Recycled Paper

Notice

ii 6C105 Overview and Setup Guide

DOC NOTICE

This digital apparatus does not exceed the ClassA limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique

édicté par le ministère des Communications du Canada.

VCCI NOTICE

This is a Class A product based on the standard of the Voluntary Control Council for Interference by

Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,

radio disturbance may arise. When such trouble occurs, the user may be required to take corrective

actions.

CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT

IMPORTANT:

Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)

that sets forth your rights and obligations with respect to the Cabletron software program (the

“Program”) contained in this package. The Program may be contained in ﬁrmware, chips or other

media. BY UTILIZING THE ENCLOSED PRODUCT,YOU ARE AGREEING TO BECOME

BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND

THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IFYOU DO NOT

AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED

PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.

Notice

6C105 Overview and Setup Guide iii

CABLETRON SOFTWARE PROGRAM LICENSE

1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this

package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the

2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the

Program.

3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws

and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and

venue of the New Hampshire courts.

EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY

1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in

writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including

its documentation and media).

CABLETRON DISCLAIMSALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO

YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING

BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE

ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.

2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL

CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER

(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,

PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,

INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)

ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,

EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR

ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME

INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO

YOU.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS

The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer

software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the

Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects

is proprietary data belonging to Cabletron and/or its suppliers.

For Department of Defense units, the product is licensed with “Restricted Rights” as deﬁned in the

DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its

successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in

subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at

252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.

Notice

iv 6C105 Overview and Setup Guide

DECLARATION OF CONFORMITY

Application of Council Directive(s):

89/336/EEC

73/23/EEC

Manufacturer’s Name:

Cabletron Systems, Inc.

Manufacturer’s Address:

35 Industrial Way

PO Box 5005

Rochester, NH 03867

European Representative Name:

Mr. J. Solari

European Representative Address:

Cabletron Systems Limited

Nexus House, Newbury Business Park

London Road, Newbury

Berkshire RG13 2PZ, England

Conformance to Directive(s)/Product Standards:

EC Directive 89/336/EEC

EC Directive 73/23/EEC

EN 55022

EN 50082-1

EN 60950

Equipment Type/Environment:

Networking Equipment, for use in a

Commercial or Light

Industrial

Environment.

We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged

with this notice conforms to the above directives.

Manufacturer Legal Representative in Europe

Mr. Ronald Fotino Mr. J. Solari

___________________________________ ___________________________________

Full Name Full Name

Principal Compliance Engineer Managing Director - E.M.E.A.

___________________________________ ___________________________________

Title Title

Rochester, NH, USA Newbury, Berkshire, England

___________________________________ ___________________________________

Location Location

6C105 Overview and Setup Guide v

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 Using This Guide.........................................................................1-1

1.2 Structure of This Guide................................................................1-1

1.3 Document Conventions...............................................................1-2

1.4 Using the 6C105 Manual Set.......................................................1-2

1.5 Getting Help.................................................................................1-3

1.6 Overview......................................................................................1-4

1.7 Features ......................................................................................1-5

CHAPTER 2 INSTALLATION REQUIREMENTS AND

SPECIFICATIONS

2.1 Site Guidelines ............................................................................2-1

2.2 Configuration Guidelines.............................................................2-2

2.3 Operating Specifications..............................................................2-2

2.3.1 Physical Specifications ...................................................2-3

2.3.2 Power Supply Requirements ..........................................2-4

2.4 LEDs............................................................................................2-4

2.4.1 Power Supply LEDs........................................................2-4

2.4.2 Fan Tray LED .................................................................2-6

CHAPTER 3 6C105 SETUP

3.1 Unpacking the 6C105..................................................................3-1

3.2 Setting Up the 6C105..................................................................3-2

3.2.1 Installation Order ............................................................3-2

3.2.2 Installing the Cable Management Bar.............................3-3

3.2.3 Rack Mounting the 6C105 ..............................................3-4

3.2.4 Attaching the Electrostatic Discharge Wrist Strap ..........3-5

3.2.5 Installing a Power Supply Module...................................3-6

3.2.6 Installing 6C105 Interface Modules ................................3-9

3.3 Powering Up a 6C105 with AC Power Supplies........................3-11

3.4 Powering Up a 6C105 with DC Power Supplies........................3-11

3.4.1 Connecting a 6C205-2 to a 48/60 VDC Power Source.3-13

3.5 Removing and Reinstalling the Fan Tray ..................................3-14

3.5.1 Removing the Fan Tray ................................................3-14

3.5.2 Reinstalling the Fan Tray..............................................3-15

Contents

vi 6C105 Overview and Setup Guide

6C105 Overview and Setup Guide 1-1

CHAPTER 1

INTRODUCTION

Welcome to the Cabletron Systems

6C105 SmartSwitch 6000 Overview

and Setup Guide

. This guide explains how to set up and conﬁgure the

Cabletron Systems 6C105 SmartSwitch 6000 chassis.

1.1 USINGTHIS GUIDE

Read through this guide completely to familiarize yourself with its

contents and to gain an understanding of the features and capabilities of

the 6C105 SmartSwitch 6000. This guide lists the features and options of

the 6C105 SmartSwitch 6000 and explains how to remove and reinstall

the fan tray, and install the power supply(ies), modules and the cable

management bar. A general working knowledge of data communications

networks is helpful when setting up the 6C105 SmartSwitch 6000.

1.2 STRUCTURE OFTHIS GUIDE

This guide is organized as follows:

Chapter 1,

Introduction

, provides manual organizational information,

how and where to get help, and discusses the features and capabilities of

the 6C105.

Chapter 2,

Installation Requirements and Speciﬁcations

, lists the

location requirements that must be met before installing the 6C105 in a

cabinet or rack. This chapter also includes some conﬁguration guidelines,

environmental guidelines, and operating speciﬁcations for the 6C105 and

related Power Supply Modules.

Chapter 3,

6C105 Setup

, contains instructions for rack mounting the

6C105, removing and reinstalling the fan tray, installing the power

supply(ies), installing a module, installing the cable management bar, and

powering up the 6C105.

NOTE

In this document, the 6C105 SmartSwitch 6000 is referred to

as either the “6C105” or the “chassis”.

Chapter 1:

Introduction

1-2 6C105 Overview and Setup Guide

1.3 DOCUMENT CONVENTIONS

Throughout this guide the following symbols are used to call attention to

important information.

1.4 USING THE 6C105 MANUAL SET

Other manuals have been developed for the interface modules that can be

installed in the 6C105 chassis. These manuals explain how to install the

modules into the 6C105, how to attach cable segments to the modules,

and how to conﬁgure the modules using Local Management after

installation is complete. Speciﬁcations for all modules are included in

each manual.

Each manual in this set assumes that the qualiﬁed personnel installing the

module has a general working knowledge of data communications

networks and their physical layer components.

NOTE

Note

symbol. Calls the reader’s attention to any item of

information that may be of special importance.

CAUTION

Caution

symbol. Contains information essential to avoid

damage to the equipment.

Electrical Hazard Warning

symbol.Warns against an action

that could result in the presence of an electrical hazard.

Autres manuels pour 6C105

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cabletron Systems Changer

Cabletron Systems

Cabletron Systems SmartSwitch 9A100 Instructions de montage

Cabletron Systems

Cabletron Systems MRX Manuel utilisateur

Cabletron Systems

Cabletron Systems 3E02-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartStack STS16-20R Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9H531-24 Manuel utilisateur

Cabletron Systems

Cabletron Systems FPIM 02 FPIM-02 Manuel utilisateur

Cabletron Systems

Cabletron Systems 7C03 MMAC SmartSWITCH Manuel utilisateur

Cabletron Systems

Cabletron Systems Cyber SWITCH 1000 Manuel utilisateur

Cabletron Systems

Cabletron Systems bridges Manuel utilisateur

Cabletron Systems

Cabletron Systems 6H122-16 Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9E312-12 Document technique

Cabletron Systems

Cabletron Systems MMAC-Plus 9E423-24 Manuel utilisateur

Cabletron Systems

Cabletron Systems 7F06-02 FDDI SmartSwitch Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSTACK 100 ELS100-24TX Instructions d'installation et d'utilisation

Cabletron Systems

Cabletron Systems FN100 Manuel utilisateur

Cabletron Systems

Cabletron Systems 9G421-02 Document technique

Cabletron Systems

Cabletron Systems Spectrum 2E42-27 Manuel de programmation

Cabletron Systems

Cabletron Systems 3T02-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems TRFMIM 28 TRFMIM-28 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-24TXG Mode d’emploi

Cabletron Systems

Cabletron Systems MMAC-Plus SFCS-1000 Feuille d'instructions

Cabletron Systems

Cabletron Systems SEHI SEHI100TX- Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9T125-24 Manuel

Cabletron Systems

Cabletron Systems SmartSTACK EPIM1000-S1LX 1000BASE-LX Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur