Cabletron Systems FN10 Manuel utilisateur

9031801-01 Page 1

Fast Network 10 (FN10) Quick Setup

Unpack the FN10 from the shipping carton. Be sure to save all shipping material.

Make sure the following items were included with the FN10:

Fast Network 10 User Guide

Fast Network 10 LCM Commands Reference Card

Fast Network 10 MIB Reference Guide

Console Cable Kit

AC power cord

Four stick-on feet (for desktop installation)

Two rack-mount brackets with fasteners

Examine the FN10 for any damage. If you suspect a problem, call Cabletron Systems

Technical Support.

If you are rack mounting the FN10, see

“Rack-mounting a FN10” in Chapter 2 of the

Fast

Network 10 User Guide

for rack mounting instructions.

If you are installing the FN10 on a

desktop, do not place a monitor on top of the unit.

To power up the FN10, plug the AC power cord into the AC power connector on the rear of

the FN10 chassis and plug the other end of the power cord into a three-prong grounded

outlet. The input voltage must be between 90 - 250

VAC

If you are going to manage the FN10 using the Local Console Monitor (LCM), connect your

ASCII terminal, or terminal emulator, to the out-of-band management RS232C port on the

front panel of the FN10 using a standard 9-pin serial cable (Only three of the nine wires are

necessary: Receive Data, Transmit Data, and Ground).

Be sure your terminal is set to the

following: 9600 baud, 8 data bits, 1 stop bit, and no parity.

Press the Enter key several times. If the FN10 is operational, the LCM prompt,

FN10>

, is

displayed on your terminal’s screen.

Step

9031801-01 Page 2

To manage the FN10 from one of its RJ45 ports, you will need to assign an IP (Internet

Protocol) address to the port that will be performing management functions. At the

FN10>

prompt, type:

ipaddr

[port number]

[IP address]

. For example:

ipaddr 6 192.138.217.40

For more information

Refer to the following chapters in the

Fast Network 10 User Guide

Topic Chapter

Product Description 1

Installation 2

Local Console Manager (LCM) 1 & 2

Enabling Bridging 3

Modifying MIB Variables 3

Statistics 4

Enabling/Disabling a Port 4

Setting up FN10 Filters 5

Power-up Diagnostics 6

Troubleshooting 6

Speciﬁcations Appendix A

Glossary Appendix B

Step

LCM command port # IP address

Autres manuels pour FN10

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cabletron Systems Changer

Cabletron Systems

Cabletron Systems SmartSwitch 6500 Instructions de montage

Cabletron Systems

Cabletron Systems SmartSwitch 1800 Manuel utilisateur

Cabletron Systems

Cabletron Systems VNswitch 900GV Instructions d'utilisation et d'entretien

Cabletron Systems

Cabletron Systems MMAC-Plus 9F310-02 Document technique

Cabletron Systems

Cabletron Systems SmartSTACK 100 Manuel utilisateur

Cabletron Systems

Cabletron Systems 9A426-02 Manuel utilisateur

Cabletron Systems

Cabletron Systems 3T02-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-S24TX2M Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSTACK 100 ELS100-24TX Instructions d'installation et d'utilisation

Cabletron Systems

Cabletron Systems MMAC-Plus 9H531-18 Manuel utilisateur

Cabletron Systems

Cabletron Systems 9A656-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartCell 6A000 Manuel utilisateur

Cabletron Systems

Cabletron Systems CyberSWITCH CSX150 Manuel utilisateur

Cabletron Systems

Cabletron Systems MicroMMAC-24E Manuel utilisateur

Cabletron Systems

Cabletron Systems 2E43-51 Manuel utilisateur

Cabletron Systems

Cabletron Systems MRX Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9H531-18 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSTACK 100 ELS100-16TX Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9A000 Manuel utilisateur

Cabletron Systems

Cabletron Systems FN100 Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9H423-26 Manuel

Cabletron Systems

Cabletron Systems MMAC-Plus 9G426-02 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartCell 6A000 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur