Cabletron Systems CSX200 CyberSWITCH Manuel utilisateur

—1——4—

Printed On Recycled Paper

WPIM SETUP GUIDE

This Setup Guide provides the information

necessary to prepare and install a Cabletron

Systems WPIM.This Setup Guide should be used

only after you have read the detailed preparation

and installation instructions contained in the

CSX200

CSX400 and CSX400-DC

, and

HSIM-W6

User’s Guides

If you need additional support related to this device,

refer to the

CSX200

CSX400 and CSX400-DC

, and

HSIM-W6 User’s Guides

. Locate these guides by

clicking on the Cabletron Systems QuickSET

program group icon on your desktop after installing

the QuickSET CD.

NOTE:

SomeWPIMs for the CSX200, CSX400 and

CSX400-DC, and HSIM-W6 require version 1.02 or

greater of QuickSET to participate and function

correctly in your network. Contact Cabletron

Systems for technical support to obtain the latest

version of QuickSET. Refer to the

Getting

Help

section of this Setup Guide.

UNPACKING THE WPIM

1. Carefully remove the WPIM from the container.

2. Visually inspect the WPIM. If there are any signs

of damage, contact Cabletron Systems

immediately. Refer to the

Getting Help

section of

this Setup Guide.

Only qualiﬁed personnel should install the

WPIM.This Setup Guide is intended for the

experienced network equipment installer.

Both the WPIM and the unit in which the

WPIM is installed are static sensitive

devices.Use a grounding strap and follow all

static safe precautions during installation.

Failure to do so could result in damage to the

WPIM and the unit receiving it.

WPIM LEDs

WPIM LED indications may vary depending on the

module or chassis in which a WPIM is installed into.

For more information on LED indications, refer to the

Troubleshooting

chapter of the

CSX200

CSX400

and CSX400-DC

, and

HSIM-W6 User’s Guides

GETTING HELP

If you need additional support related to this device,

or if you have any questions, comments, or

suggestions concerning this Quick Setup Guide,

contact the Cabletron Systems Global Call Center:

Phone: (603) 332-9400

Internet mail: suppor[email protected]

BBS: (603) 335-3358

www: http://www.cabletron.com/

(For additional information about

Cabletron Systems products)

NOTICES

Cabletron Systems reserves the right to make changes in

speciﬁcations and other information contained in this document

without prior notice.The reader should in all cases consult

Cabletron Systems to determine whether any such changes have

been made.The hardware, ﬁrmware, or software described in this

manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR

ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL

DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO

LOST PROFITS) ARISING OUT OF OR RELATED TO THIS

MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF

CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR

SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.

Order Number: 9032302-01, August 1997

P.O. Box 5005, Rochester, NH 03866-5005

Printed in the United States of America

—3——2—

Figure 1 Installing the WPIM

POST-INSTALLATION

1. Reinstall the cover or module as applicable.

2. Refer to the

CSX200

CSX400 and CSX400-DC

and

HSIM-W6 User’s Guides

to reinstall network

cables and ensure that you have the correct cable

for the installed WPIM.

3. Refer to instructions contained in the

CSX200

CSX400 and CSX400-DC

, and

HSIM-W6 User’s

Guides

or the respective QuickSTART Guides to

reapply power.

4. After reapplying power, check the LEDs for the

following conditions:

• Verify that the

PWR

LED

is on, indicating that the

device is receiving power.

• After the device runs a self test, the

CPU

LED

blinks green indicating normal operation.

• If the

CPU

LED remains red, the processor is

faulty; contact Cabletron Systems.

REQUIRED QuickSET OPERATIONS

Before the device and the WPIM can participate and

function correctly in your network, you must

reconﬁgure your QuickSET software for the WPIM.

The QuickSET Wide Area conﬁguration window for

the WPIM installed displays after clicking on the

Next>>

button in the Ethernet conﬁguration window.

The Ethernet conﬁguration window displays after

navigating the ﬁrst and second introductory

windows.

WPIM

WPIM Screws

Standoffs

WPIM

Connector Pins

WPIM

Connector

PRE-INSTALLATION

To prepare the device for WPIM installation, you

must disconnect the device from the network, and

remove the cover from the CSX200, CSX400, and

CSX400-DC or remove the HSIM-W6 module.To

prepare the device for WPIM installation, proceed

as follows:

1. Turnoffand disconnectthedevice from thepower

source.

2. Mark all network cables attached to the device for

ease of re-installation.

3. Disconnect all network cables attached to the

device.

4. Refer to detailed instructions contained in the

CSX200

, and

CSX400 and CSX400-DC User’s

Guides

to remove the chassis cover, and the

HSIM-W6 User’s Guide

to remove the module.

This procedure must be completed before

installing the WPIM.

INSTALLING THE WPIM

To install the WPIM into the device, refer to Figure 1

and complete the following steps:

1. Remove the blank faceplate from the appropriate

WAN slot by removing the three WPIM screws

that secure it to the standoffs.

2. Orient the WPIM as shown in Figure 1.

3. Carefully insert the WPIM connector into the

WPIM connector pins on the device.

4. Press down firmly on the WPIM until the pins slide

all the way into the connector. Ensure that the

WPIM seats flush on the standoffs.

5. Secure the WPIM to the three standoffs with the

WPIM screws.

When removing an existing WPIM, make

sure to pull the module straight up to avoid

damaging the connector.

Autres manuels pour CSX200 CyberSWITCH

Ce manuel convient aux modèles suivants

Autres manuels Cabletron Systems Routeur réseau

Cabletron Systems

Cabletron Systems SmartSwitch 8-slot Instructions de montage

Cabletron Systems

Cabletron Systems SSR 2000 Manuel utilisateur

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 Manuel utilisateur

Cabletron Systems

Cabletron Systems ESX-1380 Manuel de programmation

Cabletron Systems

Cabletron Systems SmartSTACK ELS100-24TXG Manuel utilisateur

Cabletron Systems

Cabletron Systems 2H253-25R Manuel d'utilisation

Cabletron Systems

Cabletron Systems MMAC-Plus 9F106-01 Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9T101-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSWITCH 7H02-06 Manuel utilisateur

Cabletron Systems

Cabletron Systems Cabletron SmartSwitch Router 250 Manuel utilisateur

Cabletron Systems

Cabletron Systems BRIM-WT1 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch Router Manuel utilisateur

Cabletron Systems

Cabletron Systems MMAC-Plus 9W111-08 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch Router 520 Manuel de l'opérateur

Cabletron Systems

Cabletron Systems BRIM-E6 Manuel utilisateur

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 Manuel utilisateur

Cabletron Systems

Cabletron Systems ELS100 Manuel utilisateur

Cabletron Systems

Cabletron Systems BRIM E100 BRIM-E100 Manuel utilisateur

Cabletron Systems

Cabletron Systems CyberSWITCH CSX400 Manuel utilisateur

Cabletron Systems

Cabletron Systems ELS100 Manuel utilisateur

Cabletron Systems

Cabletron Systems SmartSwitch 9000 Manuel utilisateur

Cabletron Systems

Cabletron Systems CSX200 CyberSWITCH Manuel utilisateur

Cabletron Systems

Cabletron Systems 3H02-04 Manuel utilisateur

Cabletron Systems

Cabletron Systems CyberSWITCH CSX500 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité