Burkert 0420 Manuel utilisateur

Operating Instructions Type 0420

Marking (example):

Body Material

PL = Polyamide Plastic

Seal Material

NBR = NBR

FKM = FKM

Circuit Function

G = 4-way

Recorder No.

Voltage / Frequency / Power Consumption

Maximum Pressure

Approvals

The valve is either approved as

General Purpose valve for Hazardous Locations

Class I, Division 1, Group A, B, C, D

Class II, Division 1, Group E, F, G

Class III, Division 1 and 2

Operating Temperature T 4

or General Purpose valve for Hazardous Locations

Class I, Division 1, Group A, B, C, D

Class II, Division 1, Group E, F, G

Class III, Division 1 and 2

Operating Temperature T 6

or FM approved as

Nonincendive for Hazardous Locations

Class I, Division 2, Group A, B, C, D

Class II, Division 2, Group F, G

Class III, Division 1 and 2

Operating Temperature T 4A

UL listed for Ordinary locations

CSA approved for Ordinary locations

See label on the valve.

Operating Instructions 0605/08_EU-EN_00893139

Table 1 Seal materials

Fluid Tempera-

tures [°F] Buna "N" (B) FKM (F)

Air Fluid T.

Ambient + 14 to + 122

+ 14 to + 122 + 14 to + 122

+ 14 to + 122

Neutral

gas Fluid T.

Ambient + 14 to + 122

+ 14 to + 122 + 14 to + 122

+ 14 to + 122

Design:

4-way solenoid valve, internally piloted, in the de-energized

condition port P connected to port B and port R connected to

port A. With manual override and flow restrictors.

Seal Materials and Fluids handled:

See Table1.

Fluid and Ambient Temperature:

For Hazardous Locations Div. 1 (T6 rated)

Max. Ambient Temperature 104 °F (40 °C)

Max. Fluid Temperature 140 °F (60 °C)

For Hazardous Locations Div. 2 and Ordinary Locations:

See Table1.

Pressure Range:

Minimum pressure differential between inlet and outlet port is

35 PSI.

Maximum inlet pressure see label on valve.

Installation:

Installation position as required. Ensure exhaust outlets for

pilot valve and main valve remain unrestricted but protect

against entry of dust, water and foreign matter. Pipework

should be clean. Do not put any loads on coil unit. Pipework

should be supported and installed to prevent strain on valve

body. Fittings should be sealed with PTFE tape, max. torque

80 in-lbs. Mounting is accomplished by means of two M4 self-

locking threaded brass inserts located on the valve

underside. Maximum thread depth is 6 mm.

Operating Instructions

Wiring Diagram

Electrical Connection Type 2509

Electrical Connection:

Ensure supply voltage/frequency corresponds with that on label.

Voltage tolerance is ± 10 %.

Available Electrical Connections see “Marking”.

Wiring diagram see above.

For this product to be considered UL-listed and CSA approved

for General Purpose and FM approved for Hazardous Locations

Division 2, it must be in conjunction with the type 2509 cable plug

connector (Electrically Operated Valves Parts, YSYI2).

The connector and gasket must be assembled to the valve with the

screw provided after the connection of the wire leads. This valve

and connector assembly is delivered together and is to be used as

one unit.

For valves to be used in Intrinsically Safe Applications the positive

pole is identified by a “+” on the pin or wire No. 1 has to be con-

nected to the “+”.

See Control Drawing for the Rules of Interconnection.

Warning:

All valves to be used in Intrinsically Safe Applications must be

clearly marked as Intrinsically Safe Apparatus.

Trouble-Shooting:

Check port connections, minimum operating pressure differential

if required and supply voltage. Ensure pilot hole in piston is clear

and pilot bore in the valve outlet is not abstracted. If core does not

pull in, check for short circuit, coil burn-out or foreign matter im-

peding core movement. A jammed or missing core causes the coil

to overheat in the case of AC supply.

Warning:

These products are designed to operate in a wide variety of ap-

plications, it is the user’s responsibility to select a model that is

appropriate for the application. This product is designed to be

installed only by suitably qualified and trained personnel.

Specifications should not be exceeded under any circumstances.

The torque for the terminal screw on type 2509 is 0,5 Nm

(4,4 lbf-in.).

Changes made to this product will render any applicable warranty

null and avoid.

Specifications subject to change without notice.

Any questions? Please call Bürkert Contromatic Technical Service

at (949) 223 31 00.

Power*

Ground (green dot)

* Orientation is not important

Germany

Contact address:

Bürkert Fluid Control Systems

Sales Center

Chr.-Bürkert-Str. 13-17

D-74653 Ingelﬁngen

Tel. + 49 (0) 7940 - 10 91 111

Fax + 49 (0) 7940 - 10 91 448

E-mail: [email protected]

International

Contact addresses can be found on the Internet at:

www.burkert.com Bürkert Company Locations

Autres manuels Burkert Unité de contrôle

Burkert

Burkert 5406 Manuel utilisateur

Burkert

Burkert 0330 Manuel utilisateur

Burkert

Burkert 6013 Manuel utilisateur

Burkert

Burkert PTB 00 ATEX 2202 X Manuel utilisateur

Burkert

Burkert 6520 NAMUR Manuel utilisateur

Burkert

Burkert 5420 Manuel utilisateur

Burkert

Burkert 2030 Manuel utilisateur

Burkert

Burkert 6027 Manuel utilisateur

Burkert

Burkert 6013 Manuel utilisateur

Burkert

Burkert 6128 Manuel utilisateur

Burkert

Burkert 3323 Manuel utilisateur

Burkert

Burkert 6650 Manuel utilisateur

Burkert

Burkert 2060 Manuel utilisateur

Burkert

Burkert 2030 Manuel utilisateur

Burkert

Burkert 6516 Manuel utilisateur

Burkert

Burkert 6520 NARMUR Manuel utilisateur

Burkert

Burkert 2060 Manuel utilisateur

Burkert

Burkert 2610 Manuel utilisateur

Burkert

Burkert 0127 Manuel utilisateur

Burkert

Burkert 2301 Series Manuel utilisateur

Burkert

Burkert 0131 Manuel utilisateur

Burkert

Burkert 6510 Manuel utilisateur

Burkert

Burkert 2060 Manuel utilisateur

Burkert

Burkert 2657 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur