Brother GT-3 Series Manuel utilisateur
GT-3 Series
GARMENT PRINTER
For Macintosh
Instruction Manual
Please be sure to read this manual before using this product.
Keep this manual in a safe place for the future use.
Table of contents
1. Before Using Your Printer for the First Time 1-1
1-1. Be sure to read the following notes before using the printer..................................................................................................1-1
1-2. Operating environment............................................................................................................................................................1-2
2. Connection of printer with Macintosh PC (Apple Computer) 2-1
2-1. Installing printer driver onto your PC .......................................................................................................................................2-1
2-2. Connecting the printer to your PC via a USB 2.0 cable .........................................................................................................2-2
2-3. Connecting the printer to your PC via a LAN cable................................................................................................................2-4
3. Print data transmission by means of Brother GT-3 FileOutput 3-1
1-1
1 Before Using Your Printer for the First Time
1-1. Be sure to read the following notes before using the printer
Keep in mind the following points before using the application:
Precautions for proper use
To set up the printer or perform its maintenance, be sure to refer the Instruction Manual and use a Windows PC
to perform the necessary operations. These operations are unavailable for Mac PC because the [GT-3
Maintenance] cannot be installed onto it.
To update the firmware of printer, be sure to refer the Instruction Manual and use a Windows PC to perform the
updating operation. This operation is unavailable for Mac PC because the [GT-3 Firmware Update] cannot be
installed onto it.
For printing out an image data that contains the transparent information, please use the PDIP for PNG image.
When you create print data from other application except PDIP, be sure to refer the Instruction Manual and use
a Windows PC to perform the data creation operation. Note that Mac PC cannot perform [Transparent Layer
Settings].
About trademarks
The names of operating systems described in the main context of this manual are abbreviated. Product names used in
this manual are, in general, trademarks or registered trademarks of their respective developer or manufacture. However,
in this manual, the ® marks or TM marks are not used.
Brother logo is registered trademark of Brother Industries, Ltd.
Microsoft®、Windows®7, Windows®8.1 and Windows®10 are trademarks and registered trademarks of Microsoft
Corporation in the United States of America and other countries.
Apple, Macintosh, Mac OS, iOS, OS X, Safari, iPad, iPhone, iPod and iPod touch are registered trademarks of Apple Inc.
in the United States of America and other countries.
Other product and company names mentioned herein may be the trademarks or registered trademarks of their
respective owners.
Information in this document and the specifications of this product are subject to change without notice.
1-2
Before Using Your Printer for the First Time
1-2. Operating environment
Compatible OS Mac OS X 10.11 El Capitan
Interface USB 2.0, LAN (10 BASE-T and 100 BASE-TX), USB flash memory (Please
use a FAT32-formatted USB flash memory of which storage capacity is 32 GB
or less.)
Min. operating environment CPU: 2 GHz or better
RAM: 1 GB or more
Display resolution XGA (1024 x 768) or higher
2-1
2 Connection of printer with Macintosh PC (Apple Computer)
This chapter provides information about the procedures to install the GT-3 printer driver onto your PC.
If you connect an USB 2.0 cable to your PC after these installation procedures are completed, make your setting by
following the procedures described in the "2-2. Connecting the printer to your PC via a USB 2.0 cable >>P.2-2". If you
want to perform a network printing, establish a network printing setup in accordance with the "2-3. Connecting the printer
to your PC via a LAN cable >>P.2-4".
2-1. Installing printer driver onto your PC
To begin with, onto your PC, install the printer driver for file output, Brother GT-3 FileOutput.
At this stage, do not connect the printer to your PC yet.
<TIPS>
You must log into your PC with administrator privileges.
(1) Activate the PC.
(2) Complete all of the current sessions.
(3) Double-click on the [BrotherGT-3_ver***.pkg] to execute installer.
(4) Then, the installation procedures will begin. Follow the on-screen instructions to complete the installation.
(5) After the installation is completed, reactivate the PC.
2-2
Connection of printer with Macintosh PC (Apple Computer)
2-2. Connecting the printer to your PC via a USB 2.0 cable
(1) With the printer powered on, make a connection of USB 2.0 cable between the printer and your PC.
(2) From the Apple menu, open the [System Preferences] and click on the [Printers & Scanners].
(3) After that, click the + button in the lower-left corner.
(4) Select the [Brother GT-3xx] first, then click on the [Select Software…] of [Use].
2-3
Connection of printer with Macintosh PC (Apple Computer)
(5) Select the [Brother GT-3] and click on the [OK].
(6) Then, click [Add].
(7) In the [Default printer], select either [Brother GT-3xx] or [Brother GT-3 FileOutput].
This exits the setting for the USB connection.
2-4
Connection of printer with Macintosh PC (Apple Computer)
2-3. Connecting the printer to your PC via a LAN cable
When you connect your PC to the printer via a LAN cable, make IP address setting for the printer from Windows PC by
reference to Instruction Manual.
Subsequently, perform the procedures below to add the printer to your PC.
(1) Connect your PC with the printer by means of the LAN cable to make a network connection, and power on the
printer.
<TIPS>
For this connection of the LAN cable, secure it in place by means of the cable clamp as required.
(2) From the Apple menu, open the [System Preferences] and click on the [Printers & Scanners].
(3) After that, click the + button in the lower-left corner.
(4) Select [IP].
2-5
Connection of printer with Macintosh PC (Apple Computer)
(5) In the [Address], enter the IP address of the printer you have just set up.
Select the [Line Printer Daemon - LPD] of [Protocol].
In the [Queue], type in the word "BINARY_P1".
Enter the name of the printer in the [Name].
Click on the [Select Software…] of [Use].
(6) Select the [Brother GT-3] and click on the [OK].
(7) Then, click [Add].
2-6
Connection of printer with Macintosh PC (Apple Computer)
(8) Then, the current window goes back to the [Printers & Scanners] window into which the GT-3 printer (LAN) is
added.
In the [Default printer], select your desired GT-3 printer, as required.
This exits the setting for the LAN connection.
Autres manuels pour GT-3 Series
10
Table des matières
Autres manuels Brother Imprimante
Brother
Brother HL-2070N Manuel utilisateur
Brother
Brother DX-2000 Manuel utilisateur
Brother
Brother HL-L8260CDW Instructions d'utilisation et de sécurité
Brother
Brother HL-3070CW Manuel utilisateur
Brother
Brother MFC-7860DW Manuel utilisateur
Brother
Brother HL-2070N Manuel d'utilisation et d'entretien
Brother
Brother mfc-j947dw Manuel utilisateur
Brother
Brother HL-1270N Manuel utilisateur
Brother
Brother MFC-L2710DN Manuel utilisateur
Brother
Brother HL-L3230CDN Manuel utilisateur
Brother
Brother TP-M5000N Manuel d'utilisation
Brother
Brother HL-L5000D Manuel utilisateur
Brother
Brother Pocket Jet PJ-722 Manuel utilisateur
Brother
Brother DCP-J4120DW Manuel utilisateur
Brother
Brother P-Touch 1800 Manuel utilisateur
Brother
Brother HL-2070N Instructions d'installation
Brother
Brother GT-541 Manuel utilisateur
Brother
Brother HL-1650 Manuel utilisateur
Brother
Brother MFC-T910DW Manuel utilisateur
Brother
Brother GTX600SB Guide de l'utilisateur
