Brother HL-630 Manuel utilisateur
1
Brother Laser Printer HL-600 Series Quick Setup Guide
Read this guidebook first to set up your printer.
Action 1: Getting Started
Check the Supplied Items
After taking the printer out of the carton and removing the packing materials, make sure that
the following items are not damaged and none are missing:
• Printer • Multi-purpose sheet feeder
• Drum unit • Toner cartridge
• 3.5” floppy disks for DOS/Windows®
• Software setup guide
• Quick setup guide (this guidebook)
• User’s guide
• Plastic Bag
NOTE
The 3.5” floppy disks for the Macintosh printer driver is included in some countries.
You will need to purchase an interface cable that matches the interface of your computer. If
you do not know what cable you need, consult your dealer.
The product names in this guidebook are trademarks or registered trademarks of each manufacturer. The specifications are subject to change without notice.
© 1994 Brother Industries, Ltd. UL5455001 C Printed in Japan
2
Action 2: Install the Toner Cartridge / Drum Unit
1Unpack the drum unit and gently rock it
from side to side five or six times.
2Remove the protective parts, in order, as
shown in the illustration.
NOTE
Do not expose the drum unit to light for
longer than a few minutes, as this will
damage the drum.
3Open the top cover. Open the drum cover
by pushing the two blue tabs in toward the
center of the unit and lifting the cover
toward you.
4Install the drum unit into the printer.
Make sure that you gasp the ▲marks.
3
5Unpack the toner cartridge and gently rock
it from side to side five or six times before
installing. ( ①)
Then, remove the protective parts.( ②)
CAUTION
DO NOT MOVE THE SHUTTER LEVER
UNTIL THE CARTRIDGE IS
INSTALLED.
6Install the toner cartridge into the drum
unit. Make sure that the ▲marks are
aligned.
7Gently pull the blue shutter lever on the
toner cartridge forward until the red arrows
are aligned.
8Close the drum cover ( ①) and push gently
until it clicks into place.
Close the top cover. ( ②)
See “CHAPTER 5 MAINTENANCE” in
the User’s Guide for more information
about replacement of the toner cartridge.
4
Action 3: Load Paper into Your Printer
1Install the paper support into the multi-
purpose sheet feeder. (①)
Install the sheet feeder into the printer. (②)
2Open the multi-purpose sheet feeder cover.
3Load paper in the multi-purpose sheet
feeder.
NOTE
The feeder can hold up to 200 sheets of
plain paper or up to 10 envelopes.
Excessive sheets may cause paper jams.
Make sure that the paper should be stacked
below the ▲mark.
4Move the paper guide to fit the paper width.
5
5Close the multi-purpose sheet feeder cover.
6Open the output tray. ( ①)
Extend the paper support wire. ( ②)
The printer can handle paper that has the following specifications.
Paper Type Paper Size Paper Weight Sheet
Feeder Manual
Cut sheet A4, Letter, Legal, B5, A5,
3”x5”, Executive, Custom size
(70-216 x 127-356 mm)
60-135 g/m2
(16-36 lbs) ●●
Envelopes DL, C5, COM-10, Monarch ●●
Post Card 70-216 x 127-356 mm ●●
Organizer Day-Timer®, J,K,L M
70-216 x 127-356mm ●●
Labels 70 - 216 x 127-356 mm ●
Transparencies ●
See “CHAPTER 2 PAPER HANDLING” in the User’s Guide for more information.
6
Action 4: Connect Your Printer and Computer
You must connect the printer to your computer using an interface cable. A parallel cable is
used for this connection.
1Make sure that the power cord is unplugged
before connecting or disconnecting the
interface cable.
Also, make sure that the computer is turned
off.
NOTE
The shape of the power cord varies
according to the country of destination.
2Connect the parallel interface cable to the
parallel interface port of the printer. ( ①)
Secure the connection with the wire clips.
(②)
Connect the interface cable to the printer
port of the computer.
NOTE
The printer can also operate with an RS-232C/RS-422A serial interface by installing the
optional serial interface board. In some countries it is installed as standard. For more
information, see “CHAPTER 4 OPTIONS” in the User’s Guide.
For the location of your computer’s parallel printer port, see the User’s Guide of your
computer. Next skip to the section “Turning On Your Printer”. After printing a test sample
page, you will then be ready to prepare your computer’s software. For setting up the printer
software, see Software Setup Guide.
7
Action 5: Plug in and Turn on Your Printer
1Plug the power cord into the AC power
outlet.
NOTE
This printer has no power switch. The
printer has a sleep mode which allows the
printer to automatically reduce power
consumption when not in use.
2Make sure that the READY lamp is ON
after the printer has warmed up (about 60
seconds).
Printing a Test Sample Page
We recommend that you print a test page. Refer to the instructions below.
1Depress the TEST (FF/CONT) switch until
all lamps are turned ON. The printer starts
printing a test sample page.
The printed page shows the basic control
panel operations.
NOTE
If the printer does not print a test sample page exactly, see “CHAPTER 6 Troubleshooting - Q
& A” of the User’s Guide. If after reviewing the information in the User’s Guide, your printer
still cannot print the test sample page exactly, consult your dealer.
8
Shipment of the Printer
If for any reason you must ship your Printer, carefully package the
Printer to avoid any damage during transit. It is recommended that you
save and use the original packaging. The Printer should also be
adequately insured with the carrier.
Warning
When shipping the Printer, the DRUM UNIT assembly including the
TONER CARTRIDGE must be removed from the Printer and place it
in the plastic bag. Failure to remove it and place it in the plastic bag
during shipping, will cause severe damage to the Printer and will
VOID THE WARRANTY.
1 Remove the drum unit. 2 Place it in the plastic bag and fold
the plastic bag under the drum
unit.
3 Wrap it in the corrugated
cardboard. 4 Re-pack the printer.
Autres manuels pour HL-630
1
Ce manuel convient aux modèles suivants
8
Table des matières
Autres manuels Brother Imprimante
Brother
Brother HL-4000 Series Manuel utilisateur
Brother
Brother MFC-J285DW Instructions de montage
Brother
Brother HL-4000CN Manuel utilisateur
Brother
Brother QL-700 Guide de sécurité
Brother
Brother GT Manuel utilisateur
Brother
Brother HL-2460 Series Manuel utilisateur
Brother
Brother HL-3075CW Manuel utilisateur
Brother
Brother HL-1650 Manuel utilisateur
Brother
Brother HL-1060 Series Manuel utilisateur
Brother
Brother TD-2120N TD-2130N TD-2120NW Manuel utilisateur
Brother
Brother HL-1070 Manuel utilisateur
Brother
Brother HL-2290 Manuel utilisateur
Brother
Brother DCP-J1200W Manuel utilisateur
Brother
Brother DCP-L2560DW Manuel d'utilisation et d'entretien
Brother
Brother HL-L2370DWXL Manuel utilisateur
Brother
Brother HL-2220 Manuel utilisateur
Brother
Brother GT-341 Manuel utilisateur
Brother
Brother DCP-J562DW Manuel technique
Brother
Brother DCP-J4120DW Manuel utilisateur
Brother
Brother HL-L5000D Manuel utilisateur
