Bristan TS6000ECP Instructions de montage

Installation Instructions

and User Guide

Thermostatic Mixing Valve

Models Covered:

TS6000ECP

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave

them with the user.

2Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Contents

Welcome to your new Bristan Shower.

All products manufactured and supplied by Bristan are safe provided they are installed,

used correctly and receive regular maintenance in accordance with these instructions

Isolation valves must be ﬁtted to the inlet water supplies to ensure ease of future

maintenance.

This valve allows safe ﬂushing of the tap or shower to avoid installation debris to clog

up the mechanical areas of the valve. This product must not be modiﬁed in any way as

this will invalidate the guarantee.

Full access must be made available for future maintenance / servicing purposes.

This product needs to be installed in accordance with, and meet the requirements of

the Water Supply (Water Fittings) Regulations 1999 and Scottish Byelaws 2004.

If in doubt, contact a registered plumber or your Local Water Authority or the

Secretary of the Institute of Plumbing, address as follows;-

The Institute of Plumbing,

64 Station Lane,

Hornchurch,

Essex,

RM12 6NB, Tel: 01708 472791

Contents

• Speciﬁcations 3

• Installation 3-4

• General Cleaning 5

• Commissioning 5

• Maintenance 6-7

Pressure

BAR

1.0

5.0

4.0

2.0 3.0

Pressure

BAR

1.0

5.0

4.0

2.0 3.0

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

IMPORTANT: Please ensure both supply

pipes are ﬂushed before connecting the

mixing valve to prevent plumbing/pipe

debris from entering the mixing valve.

1. Choose the conﬁguration of the

elbows as per the diagram below.

Choose whether to have a top or

bottom outlet by using the blanking

cap and o-ring.

2. Plumb the pipes to the desired

location for the mixing valve.

3. Remove the backplate and mark the

position of the ﬁxing holes.

4. Drill and use the screws and plugs

provided to secure the backplate to

the wall.

5. Connect the valve to the pipework,

using ﬁlters to prevent debris

entering the valve (not supplied).

We recommend using a high

tightening torque (45-50Nm) on all

22mm compression ﬁttings to

secure the valve.

Remember: Ensure the valve is ﬁtted

with the hot inlet on the left, cold

on the right when viewed from the

front.

6. Locate the valve body on to the

backplate and secure with the

grub screw.

Maximum Static Pressure:

1.0 MPa (10.0 bar)

Maximum Pressure

Dierential:

10:1

Min: 0.01 MPa

(0.1 bar)

Max: 0.5 MPa

(5.0 bar)

Working Pressures

Inlet & Outlet

Connection

28mm

Speciﬁcations Inlet Water Temperature

5°C

20°C

Cold Water Supply

Min: 5°C Max: 20°C

Hot Water Supply

60°C

IMPORTANT

The inlet hot water must

be at least 10°C above the

required blend temperature.

TMV Designation

HP-T44 & LP-T44

Outlet

Temperature

Pre-set to

43°C

Speciﬁcations

Installation

4Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation

Component List:

Item Description Qty

1Washer 1

2Piston 1

3Thermostat Housing 1

4Wire Ring 1

5Spring Ring 1

6Large Spring 1

7Return Spring 1

8O-Ring 1

9O-Ring 1

10 O-Ring 1

11 O-Ring 1

12 O-Ring 1

13 O-Ring 1

14 O-Ring 1

15 O-Ring 1

16 Grub Screw 1

17 Bottom Cap 1

18 Adjusting Screw 1

19 Screw 2

20 Head 1

21 Spindle Nut 1

22 Adjustment Housing 1

23 Retaining Screw 1

24 Thermostat Element 1

25 Wall Plug 2

26 Hexagon Insert 1

27 Filter Washer (Part of Ball Valve) 2

28 Check Valve 2

29 Valve Body 1

30 Backplate 1

31 Control Knob 1

32 O-Ring 1

33 Blue Sleeve 1

34 Blue Indice 1

35 Ball Valve 2

36 Blanking Plug 1

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Commissioning

Bristan products are made from

premium materials, with hand polishing

and electroplated ﬁnishes.

Your shower kit should be regularly

cleaned with warm water, a mild

pH-neutral liquid soap, and polished

with a soft cloth. Any residues from

soap, toothpaste, shampoos and

shower gels can cause blemishes if

not rinsed o straight after use.

Household bleaches and cleaners

contain harsh chemicals and may

damage the surface ﬁnish. Avoid using

abrasive cloths, scouring pads, scrub

sponges, steel wool or anything similar.

Working Pressures

The valve is factory set to work at a

high pressure, with the bottom cap

open 3/4 turn. The hot arrow on the

serial sticker will be pointing towards

‘High’ on the sticker on the bottom of

the valve body.

To change to low pressure, turn the

bottom cap 1/4 turn anti-clockwise until

the hot arrow points towards ‘Low’ on

the sticker on the bottom of the valve

body.

General Cleaning

6Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Maintenance

Temperature Adjustment

This valve is pre-set to a maximum

outlet temperature of 43°C.

It can be adjusted to have a maximum

temperature between 38°C - 55°C

IMPORTANT: To comply with the

TMV scheme, this valve cannot have a

maximum outlet temperature of 44°C.

If set higher, it will no longer comply

with the TMV scheme.

Please see the TMV manual supplied

with this valve for more details.

To adjust the temperature, follow

the steps below:

1. Turn on the valve and set to the

maximum temperature.

2. Remove the knob insert from

the valve. Using a narrow bladed

screwdriver, insert through the

retaining screw and locate into the

groove of the adjusting screw (Fig 1).

3. Turn the adjusting screw clockwise

for a cooler temperature, anti-

clockwise for a hotter temperature.

4. Wait for a few minutes after adjusting

for the temperature to stabilise. Use

a thermometer to measure the outlet

temperature. Repeat steps 2 and 3

until you reach the desired result.

5. Replace the knob insert.

Temperature Stop Adjustment

This method locks the position of the

control knob so that the valve cannot

reach a higher temperature.

The valve is factory set to the position

below:

• Position the control knob so that the

stops on the inside of the knob are

positioned on each side of the lug in

the sleeve.

• Screw in the retaining screw and

follow the Temperature Adjustment

steps to calibrate the temperature.

• Replace the knob insert.

To limit temperature movement, set to

the position below:

• Position the control knob so that the

stops on the inside of the knob are to

the left of the lug in the sleeve.

• Screw in the retaining screw and

follow the Temperature Adjustment

steps to calibrate the temperature.

• Replace the knob insert.

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Maintenance

Servicing the Valve

This valve should at least be serviced

with a frequency as set out in the TMV

manual guidelines to comply with the

scheme. It may need more frequent

servicing if sited in a hard water area to

ensure optimum performance.

Please see the TMV manual supplied

with this valve for more details.

To service the valve, follow

the steps below:

1. Turn both isolating lugs to shut-o

the water supplies. (Fig 3). Remove

the valve from the wall.

2. Remove the ﬁlters from the isolating

lugs and rinse of any debris.

3. Remove the knob insert. Undo and

remove the retaining screw. Remove

the control knob, ring and sleeve to

expose the head assembly.

4. Remove the head assembly from the

body using a 29mm A/F spanner.

Remove the bottom cap and

piston assembly together with the

thermostat and return spring.

Note: The piston can be

dis-assembled further but this is

not necessary for cleaning/servicing.

5. Remove O-rings and check for

damage, replace parts if necessary.

Soak all metal components in a

suitable solution until fully de-scaled.

Grease O-rings using a WRAS

Approved grease.

Re-Assembly

1. Replace piston ensuring ease of

movement when in place. This should

move with light ﬁnger pressure.

2. Replace spring and bottom cap.

Screw in gently, DO NOT use

excessive force.

3. Unscrew the bottom cap by 1 1/4

turns to give correct gap.

4. Re-assemble the head assembly

ensuring the adjusting screw is

screwed back fully.

5. Fit the thermostat into the head

assembly. Fit the head assembly into

the valve body.

6. Re-ﬁt the sleeve and control knob,

secure with the retaining screw.

7. Fit the valve back onto the wall,

ensuring the ﬁlters are in place.

8. Complete the commissioning and

temperature adjustment steps to

re-calibrate the valve.,

At Bristan, we want to make things as easy as possible for our customers. That’s why we oer solid

guarantees on all our products, eective from the date of purchase, to give you peace of mind.

To start your free guarantee simply scan the QR code and register your product.

Alternatively visit www.bristan.com/register.

For any other queries, please call our Customer Service on 0330 026 6273 where our expert team

of advisors will be able to oer you any help and advice.

For full guarantee terms and conditions visit www.bristan.com/service-centre/guarantees.

Bristan Group Ltd.

UK: Bristan Group, B78 1SG.

EU: Masco Europe S.à.r.l.

14 Rue Strachen

6933 Mensdorf

Luxembourg

Customer Service: +44330 026 6273

Web: www.bristan.com

Email: enquire@bristan.com

A Masco Company

Part Number: 800308

Issue: D4

Table des matières

Autres manuels Bristan Unité de contrôle

Bristan

Bristan PM2 SHC3DIV C Instructions de montage

Bristan

Bristan Opac TS1503 Instructions de montage

Bristan

Bristan MT503CP Instructions de montage

Bristan

Bristan OP TS1503 EH C Instructions de montage

Bristan

Bristan PM SQSHXDIV C Manuel utilisateur

Bristan

Bristan OP TS1503 CL C Instructions de montage

Bristan

Bristan OP TS1503 EL C Instructions de montage

Bristan

Bristan N2 SHCDIV G Instructions de montage

Bristan

Bristan N2 SHCVO C Schéma de câblage

Bristan

Bristan TS4753ECP Instructions de montage

Bristan

Bristan MT503CP Instructions de montage

Bristan

Bristan MT753CP Instructions de montage

Bristan

Bristan Opac Mini MINI2 TS1203 EL C Instructions de montage

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur