Brightek C2 Instructions d'utilisation
QUICK INSTALL
快速安装
北京炜煌科技发展有限公司
Beijing Bright Technology Development Co.,Ltd
C2
快速安装手册
http://www.whkj.com.cn010‐51655555
●打印机各部件一览 Printer Parts Names
1.外壳 Shell Casing
2.锁孔 Lock hole
3.原 C1 打印机 C1 Printer
4.活动盖板 Cover Plate
5.出纸口 Outlet
6.锁 Lock
7.法兰面 Flange Face
8.锁扣孔 Lock
9.原 C1 打印机 C1 Printer
按钮开关的操作及指示灯
打印机上电后指示灯保持常亮状态，打印机缺纸时指示灯闪，不能接收数据。
正常上电后，按 LF 键走纸，SET 键无效。
自检测方式
打印机断电，按 LF 键不放手同时给打印机上电，松手，打印机就会打印出
自检条。
Operation Specification
After turning on the printer, the indicator light will keep on. When
the light flash, it shows that the paper is lacking, and the printer
can not receive data.
After turning on the printer, press the LF button, the printer will
feed paper, and the SET button is no used.
The Self Test
Press the LF button, do not release and repower the printer at the
same time，and then the printer will print out the self-check scrip.
快速安装手册
http://www.whkj.com.cn010‐51655555
●尺寸 Size
WH-C2 型尺寸 Product Size:
外形尺寸 Outline Dimension： 168mm×132mm×65mm
开口尺寸 Installation Dimension： 106mm（W）×140mm（H）
114.5mm（W）×150mm（H）
嵌入深度 Inlaid Deepness： 55mm/58mm
快速安装手册
http://www.whkj.com.cn010‐51655555
●安装 Installation
安装方法：
方法一：请把打印机嵌入部分从前面插入仪器或设备面板的安装孔内,并把螺钉从面板前
面（如图所示箭头处）穿入与螺母连接拧紧，固定好打印机。
方法二：请把打印机嵌入部分从后面插入仪器或设备面板的安装孔内,并把螺钉从面板后
面（如图所示箭头处）穿入与螺母连接拧紧，固定好打印机。
WH-C2 的安装尺寸：106mm（宽）×140mm（高）
114.5mm（宽）×150mm（高）
Installation Method
Method 1: Insert the built-in part of printer into the installing orifice of
instrument or equipment in the front. As the picture show, fix the screws (four
arrows) in front of panel, and tighten the printer.
Method 2: Insert the built-in part of printer into the installing orifice of
instrument or equipment from the back. As the picture show, fix the screws (four
arrows) from the back of panel, and tighten the printer.
Installation dimension: 106mm×140mm / 114.5mm×150mm
快速安装手册
http://www.whkj.com.cn010‐51655555
●连接 Connection
通讯连接：
请严格参照公司网站提供产品说明书进行连接。
电源连接：
WH 微打随机提供的一根带有插头的两线电源电缆,插头具有极性保护机构,电源电缆的红
色线接电源正极(+),另一线接电源负极(-)。
注意:不要将交流 220V 与打印机电源插座直接相连，工作电压应在额定电压
±5%以内,电源极性一定要接正确,否则会给打印机造成永久性损坏,炜煌公
司对此不承担保修义务。
Communication Connection
Please refer to the printer manual on company website.
Power Connection
Notice the power cable, connect the red cord to positive pole, connect the white
cord to the negative pole.
Attention： Do not connect AC to the printer directly, operating voltage should
be within ± 5% rated voltage. Power polarity must be correct, otherwise it will
cause permanent damage to printer, brightek company do not assume maintenance
compulsory upon this.
快速安装手册
http://www.whkj.com.cn010‐51655555
●装纸 Paper Roll
安装步骤：
1.如图 1，打开活动盖板，箭头位置按下开关按钮，这时打印头走纸轴、切刀与打印头分
离，轻轻拉开纸仓盖，使纸仓盖彻底打开。
2.装入打印纸，并拉出一截(超出一点撕纸牙齿)，把纸放整齐，同时注意纸的方向，有药
液一面(光滑面)向上，如图 2。
3.合上纸仓盖，打印头走纸轴压齐打印纸后稍用力把打印头走纸轴压回打印头，将打印纸
从活动盖板的出纸口中穿出来，然后关上活动盖板，如图 A 和图 B 所示。
4.接通打印机的电源，按键使机头转动，这时看一下纸是否走歪，待机，或关上电源。
Replacing the Paper Roll
1.Open the movable panel, and press the button which arrow point to as shown in
Fig 1, and undrawn the paper cover.
2. Insert the paper into the printer, Pull out a small amount of paper. Notice
the direction of the paper according to Fig.2.
3. Close the paper cover. Press the platen roller back to the printer head, pull
the paper through out the outlet of the panel, and then close the movable panel,
according to Fig.A and Fig.B.
4. Power the printer on, then press LF button, make the print head to run, and
the paper will come out. Turn off the power.
快速安装手册
http://www.whkj.com.cn010‐51655555
●清洁 Cleaning
清洁保养：
热敏打印机使用久了以后，热敏条与滚轴上会留下一些污垢，如果不及时清理会影响到打
印机的使用与寿命。我们建议您不定期做好清理。
纸仓盖打开后，用棉棒沾少许酒精，轻轻擦拭打印机热敏头，及纸仓上的滚轴。
Printer Cleaning
If the interior of the printer is dusty, print quality can decline. So please clean
the printer regularly. Open the cover of printer, then Wipe the print head with
a cleaning pen and Use a cloth moistened with an alcohol solution to clean the
paper sensor and the platen roller.
●产品规格一览表 Product Specification
项目 ITEMS 规格 SPECIFICATION
打印方式 Printing method 行式热敏打印 Direct thermal line printing
纸宽 Paper width 57mm
打印宽度 Print width 48mm
分辨率 resolution ration 8 dots/mm (384 dots/line)
打印头寿命 life of printing head 6,000,000 character lines
打印速度 Printing speed 65mm/sec(when the utilization rate is 25%)
字符大小 Character size 6x8dots, 8x16dots, or 12x24dots
汉字库 Chinese character library GB2312, 16x16dots, or 24x24dots
纸的规格 Paper supplied 57mm wide,50mmø
接口 Interface Serial(RS232C,TTL)/Parallel interface/USB
输入电源 Input power DC 9V～24V, 25W
操作温度 Operating temperature 5℃～50℃
存储温度 Storage temperature -20℃～60℃
操作湿度 Operating humidity 10%～80%
存储湿度 Storage humidity 10%～90%
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Brightek Imprimante
Brightek
Brightek AA Instructions d'utilisation
Brightek
Brightek E30 Instructions d'utilisation
Brightek
Brightek U01 Instructions d'utilisation
Brightek
Brightek E25 Instructions d'utilisation
Brightek
Brightek T1 Instructions d'utilisation
Brightek
Brightek M06 Instructions d'utilisation
Brightek
Brightek E27 Instructions d'utilisation
Brightek
Brightek WH-P12 Manuel utilisateur
Brightek
Brightek E26 Instructions d'utilisation
Brightek
Brightek C03 Instructions d'utilisation
Brightek
Brightek T3 Instructions d'utilisation
Brightek
Brightek M10 Instructions d'utilisation
Brightek
Brightek A0 Instructions d'utilisation
Brightek
Brightek U02 Instructions d'utilisation
Brightek
Brightek E16 Instructions d'utilisation
Brightek
Brightek AB Instructions d'utilisation
Brightek
Brightek U04 Instructions d'utilisation
Brightek
Brightek E32 Instructions d'utilisation
Brightek
Brightek E19 Instructions d'utilisation
Brightek
Brightek E21 Instructions d'utilisation
