Bresser 7110300 Manuel utilisateur

EN INSTRUCTION MANUAL

About this Instruction Manual

These operating instructions are to be considered a component of the device.

Please read the safety instructions and the operating instructions carefully before use.

Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction

manual must be provided to the new owner/user of the product.

GENERAL WARNINGS

•Risk of electric shock — This device contains electronic components that operate via a power source

(batteries). Children should only use the device under adult supervision. Only use the device as described in the

manual; otherwise, you run the risk of an electric shock.

• Choking hazard —Children should only use the device under adult supervision. Keep packaging material, like

plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard.

• Risk of chemical burn —Keep batteries out of the reach of children! Make sure you insert the batteries

correctly. Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and

mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and

seek medical attention.

• Risk of fire/explosion —Do not expose the device to high temperatures. Use only the recommended batteries.

Do not short-circuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could

trigger a short-circuit, a fire, or an explosion.

• Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the

Service Centre and can send the device in to be repaired, if necessary.

• Use only the recommended batteries. Do not use batteries from different brands or with different capacities.

The batteries should be removed from the unit if it has not been used for a long time.

Art.No.: 7110300

Air Quality Monitor with Wireless Sensor

Feinstaubmessgerät mit Luftqualitätssensor

www.bresser.de/P7110300

MANUAL DOWNLOAD:

EN INSTRUCTION MANUAL

DE BEDIENUNGSANLEITUNG

SCOPE OF DELIVERY

Air Quality Monitor (Main unit console), Air Quality Sensor), Operating instructions, 3x AA rechargeable batteries

for the Air Quality Sensor (NiMH, rechargeable)

BEFORE YOU BEGIN

• We recommend using alkaline batteries. If temperatures regularly fall below 0°C (32°F), we recommend using

lithium batteries.

• Avoid using rechargeable batteries. (Rechargeable batteries cannot maintain correct power requirements.)

• Insert batteries before first use, matching the polarity in the battery compartment.

2x AA batteries are required for the Air Quality Monitor and 3x AA batteries (NiMH, rechargeable) are required

for the Wireless Air Quality Sensor.

EC Declaration of Conformity

Hereby, Bresser GmbH declares that the equipment type with part number: 7110300 is in compliance

with Directive: 2014/53/EU. The full text of the EU declaration of conformity is available at the following

internet address:

www.bresser.de/download/7110300/CE/7110300_CE.pdf

UKCA DECLARATION OF CONFORMITY

Bresser UK Ltd. has issued a „Declaration of Conformity“ in accordance with applicable guidelines

and corresponding standards. The full text of the UKCA declaration of conformity is available at the

following internet address:

www.bresser.de/download/7110300/UKCA/7110300_UKCA.pdf

Bresser UK Ltd. • Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6Hf, Great Britain

NOTES ON CLEANING

• Remove the batteries before cleaning.

• Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any

cleaning fluid.

• Protect the device from dust and moisture.

INTRODUCTION

Why PM2.5?

PM2.5 (particles less than 2.5 micrometers in diameter) can penetrate deeply into the lungs, irritate and corrode

the alveolar wall, and consequently impair lungs function, thus triggering asthma attack or contributing to

cardiovascular disease. Example of PM2.5 are fine dust from vehicle exhaust, wildfire, power plant emissions, other

combustion activities.

Why PM10?

PM10 (particles less than 10 micrometers in diameter) can irritate exposed mucous such as the eyes and throat.

Thus high levels of PM10 could easily make people cough, nose run and eyes sting. PM10 includes dust from

construction sites, highways, roadways, landfills and agriculture, wind fires and bush/waste burning, industrial

source; wind-blown dust from open lands, pollen, mold spores, and fragments of bacteria.

Swiss sensor technology with MCERTS certification

The device comes with Swiss made SENSIRION Particulate Matter Sensor SPS series designed for indoor and

outdoor air quality application. Its measurement principle is based on laser scattering and innovative

contamination-resistance technology, which enables precise measurements from the device’s first operation and

throughout its lifetime of usage.

Multi-zone feature

Through our multi-zone technologies, each device has a unique device code with a user selectable channel number.

Up to 4 separate air quality sensors can be placed in an open proximity covering an area across 100m radius from

its main display unit (Air Quality Monitor).

Low maintenance

The Swiss sensor is expected to have a lifetime of over 10 years while operating continuously for 24 hours/

day. With its contamination-resistance material, there is no need for cleaning and/or maintenance, thus

avoiding problems related to sensor drift or malfunction.

OVERVIEW

Air Quality Monitor Wireless PM2.5/PM10 Air Quality Sensor

WIRELESS PM2.5/PM10 AIR QUALITY SENSOR

1. LCD display 5. [ CH1 ~ 4 ] slide switch

2. [ MODE ] key 6. [ RESET ] key

3. [ CHECK ] key 7. Battery compartment

4. Wall mounting holder 8. DC adapter USB power port

BATTERY INSERTION

1. Unscrew and remove the battery door of sensor with a screwdriver.

2. Insert the 3 rechargeable batteries (included) into the battery compartment in the

following order:

x 3

3. Screw the battery door compartment on tightly.

4. After inserting batteries, all LCD segment will be shown for 1 second.

GETTING STARTED

1. Slide [ CHANNEL ] to set the channel number for your sensor(s).

2. Use a pin to press [ RESET ] key for run the channel number.

Note:

-If there are more than one sensor in use, ensure to assign different channel numbers for each sensor to enable

the measurement is displayed correctly on the console.

LCD DISPLAY

1. PM2.5 / PM10 display mode

2. PM2.5 / PM10 concentration value

3. PM2.5 / PM10 concentration level

4. Sensor Wireless channel number

5. Transmission signal

6. Battery power indicator

DISPLAY MODE

Press [ MODE ] to toggle the display mode between PM10 and PM2.5.

MEASUREMENT INTERVAL

The device measures PM2.5 or PM10 concentration every minute automatically when powered with a DC adapter.

Manual detection

User can press [ CHECK ] button anytime to get an updated measurement of PM2.5 or PM10 concentration

readings. (It takes approximate 10-12s to detect, the readings indicated by blinking PM2.5/PM10 icon.)

Operated by batteries

When powered by batteries, it’s detecting every 10 minutes by default. To maximize the battery life, user can also

change the detection interval from 10 minutes to 20 or 30 minutes.

Setting default measurement interval

1. Press and hold [ CHECK ] for 2 seconds until the display is flashing

2. Press [ MODE ] to choose which interval time.

3. The setting sequence: 10m 20m 30m

4. Press [ CHECK ] to finish the setting and back to normal display.

Detection interval (Minute) Description

1(when connected to adapter) The sensor will detect the PM value every 1 minute

10 (default) The sensor will detect the PM value every 10 minutes

20 The sensor will detect the PM value every 20 minutes

30 The sensor will detect the PM value every 30 minutes

PM2.5/PM10 CONCENTRATION

For easy visualization of air quality, the device spreads the concentration readings over 6 level scale.

Good Hazardous

The following provides some gives health guidelines on activities between good and hazardous air quality*:

Hazardous Good

PM2.5 PM10 Healthy persons Elderly, Children, Pregnant

women

Persons with chronic

disease or heart disease

0~35 0~50 Continue with normal activities Continue with normal activities Continue with normal activities

36~53 51~75 Continue with normal activities Continue with normal activities Continue with normal activities

54~70 76~100 Reduce prolonged or strenuous

outdoor physical exertion

Minimize prolonged or

strenuous outdoor physical

exertion

Minimize prolonged or

strenuous outdoor physical

exertion

71~150 101~350 Avoid prolonged or strenuous

outdoor physical exertion Minimize outdoor activity Avoid outdoor activity

151~250 351~420 Minimize outdoor activity Avoid outdoor activity Avoid outdoor activity

251+ 420+ Avoid outdoor activity Avoid outdoor activity Avoid outdoor activity

*Always consult/check with your doctors for any medical advices concerning the air quality and your health

Note:

This 6 level scale of PM2.5 / PM10 concentration is not the same as Air Quality Index (AQI).

BATTERY POWER STATUS

The device is powered by rechargeable batteries, and comes with battery power indicator. The battery life of the

device from fully charged batteries is determined by the number of detections it performed, either through set

intervals or manually activated by user.

100% 80% 60% 40% 20% < 20%

When battery power fails to below 20%, user should recharge the batteries by connecting to a USB port using the

cable provided.

Note:

When the wireless PM2.5/PM10 air quality sensor’s battery power is below 20%, its detection function will

temporary suspension.

CHARGING THE BATTERIES

You can use the micro USB cable to charge the wireless PM2.5/PM10 sensor if the battery states show in “Low

battery”. When Micro USB port plug in the micro USB cable for charging, the LCD will display and flashing

battery icon.

: Charging underway

: Charged to full capacity

Note:

- Charged to full capacity from <20% battery power status require 24 hours.

REPLACE THE RECHARGEABLE BATTERIES

Over time, the batteries may degrade in terms of holding the highest capacity for which it was designed for. If you

find the device’s battery power is not lasting as it used to be, it’s probably a good time to change them.

1. Unscrew and remove the

battery door of sensor with a

screwdriver.

2. Pull the black ribbon lying

under the batteries. All

batteries can be removed

together.

3. Insert new 3 x AA size rechargeable batteries into the battery compartment according to the

polarity mark inside battery compartment.

4. Screw the battery door compartment on tightly.

5. After inserting batteries, all LCD segment will be shown for 1 second.

PAIRING WIRELESS SENSOR TO CONSOLE DISPLAY

This Wireless PM2.5/PM10 Air Quality Sensor can connect to the Air Quality Display console.

1. After the wireless air quality sensor is switched on, it will automatically enter registration mode for 10 minutes

until which it can be paired by the display console.

2. Once the connection is successful, the signal strength indication and PM2.5/PM10 information will

appear on the display console.

Note:

-If you need to re-assign the sensor channel, slide the channel slide switch to the new channel position, then use

a pin to press [ RESET ] key to restart the sensor.

-To avoid the sensor(s) and console pairing failure during new channel number assigned and setup, please

power up the sensor(s) first, and then press [ SENSOR ] key on the main unit.

-After connected to the console display, the reading will transmit every 12 seconds in the first 5 minutes. Every

reading transmission, the symbol of signal transmission , will flash 0.5 seconds at once.

DATA TRANSMISSION

The device transmits its updated reading at fixed interval of 60 seconds to the paired console receiver.

RESET THE SENSOR

In case of malfunction, use a pin to press [ RESET ] button to reset the sensor.

SENSOR INSTALLATION

The sensor is designed for desktop or wall mount for easy viewing. Follow the guidelines below for the sensor

placement.

1. Choose an open area away from any emissions source of pollutants, heat source, or with air flow greater than

1m/s.

2. Place the wireless PM2.5/PM10 sensor at least 1.5m to 4m above the ground to better illustrate the detection

of air quality in the human breathing zone.

3. Do not expose the sensor to direct sunlight.

Wall mounting

Sensor can be mounted on the wall at dierent angle, either at

slant angle or vertically with the mounting adapter (included).

Place a screw on the wall where you wish to hang for sensor. Hang the sensor on to the screw with

or without the mounting adaptor.

Vertical angle Slant angle

Note:

Higher siting may also be appropriate if the sensor is representative of a large area.

AIR QUALITY MONITOR

1. LCD display 9. [ DOWN ] key

2. [ MODE ] key 10. [ UP / CH ] key

3. [ SNOOZE / LIGHT ] key 11. [ PM2.5 / PM10 ] sliding switch

4. [ MAX ] key 12. [ RCC ] key

5. [ TIME SET ] key 13. [ RESET ] key

6. [ ALARM ] key 14. [ SENSOR ] key

7. Wall mounting holder 15. Battery compartment

8. [ ALERT ] key

LCD DISPLAY

1. Wireless sensor channel number

2. PM2.5 or PM10 display mode

3. AQI alert on

4. Air Quality Index (AQI)

5. Time with alarm

6. Current PM2.5 / PM10 concentration

value

7. 1 hour Maximum PM2.5 / PM10

concentration value

8. Current AQI

9. 1 hour Maximum AQI value

10. Indoor temperature & humidity

GETTING STARTED

1. Open the battery compartment door.

2. Insert 2 x AA size batteries into the battery compartment.

Make sure you insert them the right way according to the

polarity information marked on the battery compartment.

3. Close the battery compartment door.

Note:

- If no display appears on the LCD after installing the batteries, press the [ RESET ] key by using a pin.

- After 5 minutes channel searching, it will turn to RCC signal reception automatically.

-You may not receive the RCC and wireless sensor(s) signal immediately. Due to the atmospheric disturbance, the

best reception often occurs during night time.

PAIRING THE WIRELESS SENSOR

1. Make sure the Air Quality sensor is in registration mode (by pressing [ RESET]).

2. Press [ SENSOR ] in the display console to start pairing with the Air Quality sensor as indicated by blinking

3. Once the connection is successful, the sensor(s)signalstrength indication and PM2.5/PM10 information

will appear on the air quality monitor.

WIRELESS SENSOR SIGNAL INDICATOR

The main unit display signal strength of the wireless sensor(s), as shown below:

Signal searching No signal Weak signal Good signal

Note:

- If no signal received, the PM2.5 / PM10 will display “---” for the corresponding channel.

-If the signal has discontinued and does not recover within 1 hour. The PM2.5 / PM10 will display “Er” for the

corresponding channel.

-To reconnect, move the sensor closer to the display console, or press [ SENSOR ] for the display console to enter

signal searching mode.

TIME SETTING

The time on the display console can be set manually or synchronized to local time with reception of the radio-

controlled signal.

RECEPTION OF RADIO CONTROLLED SIGNAL

The clock can automatically synchronize its time with the time signal transmitted from Germany (DCF77) or UK

(MSF).

When used for the first time (after inserting the batteries or pressing the [ RESET ] key), the clock will start to receive

the RCC signal after 5 minutes with the signal indicator flashing. You can also press [ RCC ] key to receive the RC signal

once.

RCC SIGNAL INDICATOR

The signal indicator shows the reception quality of the radio-signal as shown below:

No RCC signal received Receiving RCC signal Received RCC signal

Note:

- Every day the wireless sensor will automatically search for the time signal at 2:00, 3:00, 4:00 and 17:00.

- Always place the unit away from interfering sources such as TV set, computer, etc.

- Avoid placing the unit on or next to metal plate.

- Closed area such as airport basement, tower block or factory is not recommended.

- Do not start reception on a moving article such as vehicle or train.

- User can permanent disable or enable the RC function by press and hold the [ RCC ] key for 8 seconds.

DISABLE/ENABLE RCC SIGNAL RECEPTION

1. Press [RCC] to disable the reception.

2. Press [RCC] to enable automatic RCC reception.

RCC on RCC o

DAYLIGHT SAVING TIME (DST)

This clock has been programmed to automatically switch when the daylight saving time is in effect. User can disable

the DST function in time and calendar setting mode.

Note:

DST AUTO/OFF setting only available when RCC function is ON.

MANUALLY TIME SETTING / TIME ZONE SELECTION

1. In normal mode, press and hold [ ] key for 2 seconds to enter date and time setting mode.

2. Press [ ] or [ / CH ] key to adjust the setting.

3. Press [ ] key to enter the next setting.

4. The setting sequence: 12/24 format hour minute ± 23 Hour offset °C / °F DST AUTO/

OFF

5. Press [ ] key or leave the unit for 60 seconds to complete the setting and return to normal mode.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Bresser Station météorologique

Bresser

Bresser MeteoTemp WTM Colour Manuel utilisateur

Bresser

Bresser Temeo Hygro Quadro DLX Manuel utilisateur

Bresser

Bresser TemeoTrend LGX Manuel utilisateur

Bresser

Bresser 7902586 Manuel utilisateur

Bresser

Bresser National Geographic Manuel utilisateur

Bresser

Bresser National Geographic 9080500 Manuel utilisateur

Bresser

Bresser Meteo Temp 7004200 Manuel utilisateur

Bresser

Bresser 7902585 Manuel utilisateur

Bresser

Bresser TemeoTrend WFS Manuel utilisateur

Bresser

Bresser Meteo NBF Colour Manuel utilisateur

Bresser

Bresser TemeoTrend NBF Manuel utilisateur

Bresser

Bresser 1866932 Manuel utilisateur

Bresser

Bresser 4Cast PRO SF Manuel utilisateur

Bresser

Bresser ClimaTemp TB Manuel utilisateur

Bresser

Bresser Weather Center WTW 5in1 Manuel utilisateur

Bresser

Bresser Meteo THBM Colour Manuel utilisateur

Bresser

Bresser 7003100CM3000 Manuel utilisateur

Bresser

Bresser 4CAST CV WIFI Manuel utilisateur

Bresser

Bresser ClimaTemp WS Manuel utilisateur

Bresser

Bresser WIFI ClearView Weather Station 7in1 Manuel utilisateur

Bresser

Bresser 7002585 Manuel utilisateur

Bresser

Bresser 4Cast 95-01100 Manuel utilisateur

Bresser

Bresser ClimaTemp FW Manuel utilisateur

Bresser

Bresser MyTime XL Manuel utilisateur

Manuels Station météorologique populaires d'autres marques

Auriol

Auriol AHFL 433 A1 Manuel utilisateur

NexSens

NexSens G2-HYDROMET Manuel utilisateur

Hyundai

Hyundai WS 2202 Manuel utilisateur

IROX

IROX HBVR761 UV-X Manuel utilisateur

La Crosse Technology

La Crosse Technology C86371 Manuel utilisateur

ADE

ADE WS 1711 Manuel utilisateur

Auriol

Auriol z29592 Manuel utilisateur

Auriol

Auriol 296289 Manuel utilisateur

Hyundai

Hyundai WS 2266 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-2210 Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-811561 Manuel utilisateur

Ventus

Ventus W177 Manuel utilisateur

National Geographic

National Geographic VA Colour RC Manuel utilisateur

Renkforce

Renkforce 1208067 Manuel utilisateur

Levenhuk

Levenhuk Discovery Report WA40 Manuel utilisateur

Instant Transmission

Instant Transmission MA 10410 Manuel utilisateur

Lutron Electronics

Lutron Electronics PHB-318 Manuel utilisateur

WAREMA

WAREMA EWFS Weather station eco Manuel utilisateur