Bosch D603 Manuel utilisateur

D603/D604/D605 Heat Detectors

Installation Instructions

1.0 Notice

These instructions cover the installation of the D603, D604 and D605 Heat Detectors in a fire system supervised

by a compatible Fire Alarm Control Panel (FACP).

Install, test and maintain the D603, D604 and D605 according to these instructions, NFPA 72, Local Codes and

the Authority Having Jurisdiction (AHJ). Failure to follow these instructions may result in failure of the device to

operate properly. Bosch Security Systems, Inc. is not responsible for improperly installed, tested or maintained

devices.

These instructions contain procedures to follow in order to avoid personal injury and damage to equipment.

Test the D603, D604, D605 and the FACP in accordance with NFPA 72.

1.1 FCC Compliance Notice

This device complies with Part 15 of the FCC Rules and with RSS-21 of Industry and Science Canada. Operation

is subject to the following two conditions:

(1) this device may not cause harmful interferences, and

(2) this device must accept any interference received, including interference that may cause undesirable operation.

Changes or modifications not expressly approved by Bosch Security Systems can void the user’s authority to

operate the equipment.

2.0 Device Description

The D603, D604 and D605 are Electronic Rate-of-Rise/Fixed Temperature Heat Detectors. They are designed to

work with the D200 Series bases to provide general property protection.

When properly installed using the D200 Series bases, 2-wire supervision is provided by IN/OUT wiring of the

positive (+) power line. This causes the FACP to initiate a trouble signal when a detector head is removed from its

base. 4-wire system supervision is provided by an EOL power supervision device, such as the D275, or a D293E

and an EOL resistor as specified by the FACP manufacturer.

The D603, D604 and D605 are not life-safety devices.

D603/D604/D605

3.0 Mounting the Detector

Use the following steps to mount the detector base and head:

1) Mount and wire the base according to its installation instructions.

2) Mount the detector head to the base by turning it clockwise until it clicks into place. When it is secure, the

alignment arrow will be lined up with the tamper screw hole. See Figure 1.

Tamper Screw

Location

LED

Thermistor

Te s t

Point

Base contacts

(3 sets)

Alignment

arrow

Start detector

contacts here and

rotate clockwise

Figure 1: Mounting the Detector Head to the Base

3) Use the tamper screw to prohibit detector head removal.

The detector heads are keyed and should not be forced onto the bases.

4.0 Testing the Installation

Use the following guidelines when testing the installed detector head/base combination:

• Check the wiring from the FACP to the last detector head on each run for proper polarity and continuity.

- Make sure each run terminates with an EOL resistor as specified by the FACP manufacturer.

- Make sure 4-wire runs terminate with EOL modules or D293E bases.

• Apply power to the system. Check for alarms.

- Note which detectors are in alarm (if any) and then shut the system down. Remove these detectors from their

bases and re-check the bases for proper wiring. If the problems persist, replace the affected detectors or swap

them with known good units. This will identify if the problem is caused by the detector or the base.

- In the event of a system alarm with no detector alarms present, remove all detectors and check the wiring at

each base. Pay close attention to the wiring of each EOL resistor or EOL module.

• When the system is free of alarms, check each detector to ensure that the red LED indicator is flashing

approximately every seven seconds. This verifies that the detector is receiving power and operating properly.

If the detector LED is flashing quickly (approximately once every second), the detector is either too cold or defective.

Allow it to warm slowly to room temperature. The LED should resume its normal flash pattern of approximately once

every 7 seconds. If it continues to flash quickly once the detector has reached average room temperature, the detector

is defective and must be replaced.

Testing the Installation

D603/D604/D605

Maintaining the Detector Head

• Test each detector individually to ensure it will cause a control panel alarm. Reset the control panel after each

test.

• To alarm the detectors, do one of the following:

- Place a magnet horizontally against the detector's Test Point (see Figure 1). Center the magnet over the “T”

marked on the head to activate an internal reed switch, or

- Expose the thermistor (see Figure 1) to a heat source such as a hair dryer or a shielded heat lamp. Expose the

thermistor until the detector goes into alarm and the alarm LED latches on.

When a detector alarms, the red LED indicator will activate and latch into the ON position. Be sure to clear the alarm

before proceeding to the next detector.

• Reset the detector by momentarily removing power.

• Finally, check the overall loading of the alarm loop by measuring the voltage across each EOL resistor. This

voltage should equal or exceed the minimum specified by the control panel manufacturer.

5.0 Maintaining the Detector Head

Notify all concerned parties prior to any maintenance or testing of the fire alarm system, and then again after

completion of these activities.

• At least once a year, the detector and base should be cleaned. Use a vacuum or clean/dry compressed air.

• Do not paint the detectors. Paint or other foreign matter covering the thermistor may prohibit detection.

130 Perinton Parkway, Fairport, New York, USA 14450-9199

(800) 289-0096

02/08

D603/D604/D605 Installation Instructions

P/N: F01U071135-04 Page 4

6.0 Specifications

Product Description

•D603: 135°F (57°C) Electronic Fixed Temperature/Rate-of-Rise Heat Detector (base required)

•D604: 135°F (57°C) Electronic Fixed Temperature Heat Detector (base required)

•D605: 190°F (88°C) Electronic Fixed Temperature Heat Detector (base required)

•D278S: 12 volt POPIT Base

•D287: 2-wire Base

•D292: 4-wire Base

•D293A: 4-wire Base with Built-in Auxiliary Relay

•D293E: 4-wire Base with Built-in EOL Supervision

•D293S: 4-wire Base with Built-in Sounder

•D298S: 24 volt POPIT Base (single)

•D298M: 24 volt POPIT Base (multiple)

•D275: EOL Supervision Module for 4-wire Bases

•TP280: Trimplate for use with D287 Base

Detector Power Requirements

•2-wire Standby Voltage: 8.5 to 33.0 VDC

•4-wire Standby Voltage: 10.0 to 30.0 VDC

•Maximum RMS Ripple: 25% of DC input

•Start-up Current: 120 μA maximum

•Standby Current: 90 μA max @ 12 VDC; 110 μA max @ 24 VDC; 120 μA max @ 33 VDC

Note: D293E = 24 mA @ 12 and 24 VDC

• Alarm Current (D603, D604, D605)

• With 2-Wire bases (D287): Dependent on control panel. Panel must limit the alarm current to 100 mA

maximum.

•With 4-Wire bases:

-D292: 52 mA @ 12 VDC; 54 mA @ 24 VDC; 70 mA max @ 30 VDC

-D293A: 58 mA @ 12 VDC; 62 mA @ 24 VDC; 75 mA max @ 30 VDC

-D293E: 82 mA @ 12 VDC; 86 mA @ 24 VDC; 100 mA max @ 30 VDC

-D293S: 52 mA @ 12 VDC; 54 mA @ 24 VDC

Note: Sounder current not included for D293S alarm current.

Operating Temperature

• 32°F to 100°F (0°C to 38°C)

-D603, D604: These detectors are designed to detect temperatures greater than 135°F (57°C). Do not install

in areas where the normal ambient temperature exceeds 100°F (38°C) or drops below 32°F (0°C).

-D605: This detector is designed to detect temperatures greater than 190°F (88°C). Do not install in areas

where the normal ambient temperature exceeds 190°F (88°C) or drops below 32°F (0°C).

Rate-of-Rise:D603: ≥ 15°F (9°C) per minute

Power-up Time: 22 seconds maximum

Dimensions:Diameter: 4 in. (10.2 cm)

Height: 1.3 in. (3.3 cm)

Compatible Control Panels

•2-wire: See Technical Service Note P/N: 31866.

Bosch Security Systems, Inc. makes no claim written, oral, or implied that the D603 series heat detectors will work with

any 2-wire control panels except those specified in the Base Compatibility chart in Tech Note P/N: 31866.

•4-wire: Compatible with all UL Listed 4-wire control panels. Refer to the manufacturer's Installation

Instructions for proper End-of-Line resistor selection.

Not for use on zones that incorporate an alarm verification feature.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bosch Capteur de sécurité

Bosch

Bosch DS308EA Manuel utilisateur

Bosch

Bosch D-tect 150 SV Professional Manuel utilisateur

Bosch

Bosch ISN?SM?80 Manuel utilisateur

Bosch

Bosch Blue Line P1 Manuel utilisateur

Bosch

Bosch DS794Z Manuel utilisateur

Bosch

Bosch TriTech DS970 Series Manuel utilisateur

Bosch

Bosch DS940 Manuel utilisateur

Bosch

Bosch DS940P Manuel utilisateur

Bosch

Bosch Blue Line Q1 Manuel utilisateur

Bosch

Bosch D-tect 150 Professional Manuel utilisateur

Bosch

Bosch FMC-210-SM-G-R Manuel utilisateur

Bosch

Bosch DS938Z Manuel utilisateur

Bosch

Bosch DS778 Manuel utilisateur

Bosch

Bosch CRS-SWM-TA869 Manuel utilisateur

Bosch

Bosch ISC-CDL1-W15H Manuel utilisateur

Bosch

Bosch D-tect 150 Professional Manuel utilisateur

Bosch

Bosch D300A-HV Manuel utilisateur

Bosch

Bosch IR LD 1.0 Manuel utilisateur

Bosch

Bosch DS9360 Manuel utilisateur

Bosch

Bosch Analog Detector Series Mode d'emploi

Bosch

Bosch Motion Detector Manuel utilisateur

Bosch

Bosch Blue Line D1-P Manuel utilisateur

Bosch

Bosch 200 C Manuel utilisateur

Bosch

Bosch DS935Z Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur

Solinst

Solinst 301 Manuel utilisateur