Bosch VC86775T Manuel utilisateur

VC86775T & VC86785T

Installation Instructions

Observation Camera

Manuale d'installation

Camérad'Observation

Manual de instalación

Cámara de Observación

Bosch Security Systems | 2004-07

VC86775T & VC86785T | Installation Instructions

Installation Instructions

00697

100697

200m

0-50m

100m

300m

1415

FIGURE A

Bosch Security Systems | 2004-07

VC86775T & VC86785T | Installation Instructions

4-5

2-3

4-5

2-3

CL 76610011_004.AI

FIGURE B

Bosch Security Systems | 2004-07

VC86775T & VC86785T | Installation Instructions

TABLE OF CONTENTS

ENGLISH ................................................................ 1

FRANÇAIS ............................................................. 8

ESPAÑOL ............................................................... 15

TECHNICAL SPECIFICATIONS ...................... 27

Bosch Security Systems | 2004-07

EN | 1

VC86775T & VC86785T | Installation Instructions

FCC DECLARATION

Installation InstructionsENGLISHEN

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits

for a class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and the receiver.

• Connect the equipment to a power socket on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

Bosch Security Systems | 2004-07

EN | 2

VC86775T & VC86785T | Installation Instructions

WARNING

Any unauthorized modification to this equipment could result in the

revocation of the authorization to operate the equipment.

WARNING:

To prevent fire or shock hazard, do not expose this camera

to rain or moisture. Do not attempt to disassemble the

camera. In order to prevent shock and fire hazard, do not

remove screws or covers. There are no user-serviceable

parts inside.

Bosch Security Systems | 2004-07

EN | 3

VC86775T & VC86785T | Installation Instructions

Observation Camera

INTRODUCTION

Your new CCD camera is developed for use with a special

observation system monitor. It features a sensitive microphone thus

registering both images and sound via the monitor, as well as input

contacts for connecting external alarm devices.

INSTALLATION

When the mains supply is connected, all camera lines are scanned.

The monitor uses this to register the camera configuration of the

system and to check whether any modifications have been made.

Sound

If required, the microphone incorporated in the camera, can be

switched off (fig. A-14).

If an intercom box is included in the camera line, the sound of

camera and intercom box will be reproduced by the monitor.

The illustrations to which this manual refers, are shown on the front

and back jacket flap.

WARNING:

Disconnect the monitor from the mains supply before

disconnecting a camera or accessory.

Only operating the stand-by key is not sufficient.

Bosch Security Systems | 2004-07

EN | 4

VC86775T & VC86785T | Installation Instructions

Alarm inputs

The camera has a three-pole terminal block (fig. A-13) for connecting

alarm sensors, such as doorcontacts. For normally open (N.O.)

sensors, connect to contacts N.O.. For normally closed (N.C.) sensors,

connect to contacts N.C..

Position

First you need to determine where the camera is to be installed. The

best results are obtained when the camera looks a little downwards

and not into a bright source of light.

• Hold the camera in your hand at the spot where you want to

install it and check on the monitor whether the camera does

actually cover the required area from that spot.

• Fasten the mounting bracket to the ceiling, the wall, or another

even and firm surface by means of the supplied screws and plugs.

• Tighten the knob (fig. A-3) of the ball-and-socket joint.

• Fasten the camera to the bracket by screwing the mounting hole

in the back or bottom of the camera (fig. A-l) onto the threaded

end (fig. A-2).

• Loosen the knob of the ball-and-socket joint (fig. A-3) and, if

necessary, the screw (fig. A-4) on the mounting bracket and direct

the camera accurately at the object or area you want to have on

screen.

• The knob and screw can be tightened again when the camera is

in the required position.

Remark: The camera can also be mounted on any other camera

tripod standardly provided with a 1/4" 20 UNC thread.

• Check if the cable length compensation (fig. A-15) selector is set

to the correct length. The length set must be the same as the

length of the system cable (0-300m/900ft max.) connecting

monitor and camera.

Bosch Security Systems | 2004-07

EN | 5

VC86775T & VC86785T | Installation Instructions

Focus adjustment

Adjust the focus ring (fig. B-l) of the camera lens to obtain an optimal

image sharpness.

Remark: If still no sharp object image is obtained, you should

adjust the back-focus of the camera.

Back-focus adjustment

• Set focus adjustment ring to Far or Infinity (fig. B-2).

• Aim the camera at an object at least 15 metres/45 feet away.

Remark: When bright light sources are positioned within the

camera view field; dim the light source.

• Loosen the back-focus locking ring (fig. B-3).

• Rotate the lens, including the CS-mount ring, until the video

image on the monitor is sharp.

• Tighten the back-focus locking ring (fig. B-3), while keeping the

lens in place.

Protective cover

For outdoor use a protective cover (fig. A-10) (optional) has to be

used to protect the camera from rain and snow.

System connection

Connect the system cable to the output of the camera (fig. A-12).

CAUTION:

Back-focus adjustment is only necessary when no sharp

object image is obtained with the focus adjustment ring.

Bosch Security Systems | 2004-07

EN | 6

VC86775T & VC86785T | Installation Instructions

The lens

Focus range

The built-in lens provides an optimal image sharpness for objects

between 1 metre and infinity (depth of field).

Cable

A 4-wire system cable (see specifications) is supplied standardly.

For an optimum picture and sound quality a standard dual 'twisted-

pair' cable should be used.

There is an extensive range of plugs and tools available in the hobby

and professional trade to extend the cable. Always pay attention that

the connection corresponds to figure B.

The maximum distance that can be bridged (without a cable

extension adapter) between the monitor and the cameras is 300

meters.

CAUTION:

Do not touch the glass of the lens. This could damage the

delicate coating on its surface. If the lens has to be

cleaned, use a special lens cleaning tissue, available at

any good camera store.

CAUTION:

The plugs used for the observation system have the same

dimensions as standard telephone plugs. Never connect a

telephone to the camera or system monitor.

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Bosch Caméra de sécurité

Bosch

Bosch AUTODOME IP 5000i IR Manuel utilisateur

Bosch

Bosch BasicDome Series Manuel utilisateur

Bosch

Bosch FLEXIDOME IP panoramic 6000 Series Manuel utilisateur

Bosch

Bosch VDN-5085 Manuel utilisateur

Bosch

Bosch Autodome IP 4000 HD Manuel utilisateur

Bosch

Bosch DINION IP 5000 HD Manuel du propriétaire

Bosch

Bosch WZ20NXV550‑0 Manuel utilisateur

Bosch

Bosch VG5-7230-CPT5 Manuel utilisateur

Bosch

Bosch FLEXIDOME IP indoor 5000 Manuel du propriétaire

Bosch

Bosch VJR-821-ICCV Manuel utilisateur

Bosch

Bosch NTI-40012-A3 Manuel utilisateur

Bosch

Bosch FLEXIDOME multi 7000i IR Manuel utilisateur

Bosch

Bosch VJR SERIES Manuel utilisateur

Bosch

Bosch VBN-5085 Manuel utilisateur

Bosch

Bosch EX27 Manuel utilisateur

Bosch

Bosch VEZ-400 Series Manuel utilisateur

Bosch

Bosch DINION IP starlight 7000 HD Manuel utilisateur

Bosch

Bosch NDC-225-P Manuel utilisateur

Bosch

Bosch MIC Series 550 Manuel utilisateur

Bosch

Bosch UHI Series Manuel utilisateur

Bosch

Bosch REG‑Z1‑8050‑XC‑00E‑01 Manuel utilisateur

Bosch

Bosch AN bullet 2000 IR Manuel utilisateur

Bosch

Bosch VEI-30 Manuel utilisateur

Bosch

Bosch LTC 0465 Series Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur