Bosch MIC Series 400 Manuel utilisateur
Bosch Security Systems Issue 1
MIC400 Quick Start Guide
Unit Mechanical mounting
The upright unit can be mounted either way up with the camera ball up or down. The get the picture the correct
way up for installation with camera ball down rotate the camera tilt axis over by 180 degrees.
Please refer to the MIC400 Manual for further details of configuring Image Flip and reversing the controls for IR
unit and inverted units.
The MIC400, if canted is designed only to be mounted ball up, the tilt limits for the canted unit prevent it from
working properly if mounted ball down, the MIC412 and MIC440 cannot be canted.
WARNING: INSTALLATION SHOULD BE CARRIED OUT BY QUALIFIED
PERSONNEL ONLY IN ACCORDANCE WITH THE APPLICABLE LOCAL
CODES.
BOSCH SECURITY SYSTEM ACCEPTS NO LIABILITY FOR ANY
DAMAGES OR LOSSES CAUSED DUE TO INCORRECT OR IMPROPER
INSTALLATION.
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DISCONNECT POWER SUPPLY BEFORE OPENING THE POWER
SUPPLY UNIT.
POWER DISCONNECT: POWER SUPPLY UNITS HAVE POWER
SUPPLIED WHENEVER THE POWER CORD IS INSERTED INTO THE
POWER SOURCE
WARNING: DUE CAUTION SHOULD BE EXERCISED WHEN
INSTALLING THE MIC400 RANGE OF CAMERAS, COMMON SENSE
PRECAUTIONS SUCH AS FITTING A SAFETY CHAIN SHOULD BE
FOLLOWED.
SPECIAL CARE SHOULD BE TAKEN WITH STAINLESS STEEL, MIC412
or MIC440 MODELS DUE TO THEIR EXTRA WEIGHT.
Page 2 of 3
BOSCH SECURITY SYSTEMS
Do not manually back drive the pan or tilt axis by hand. Back driving may strip teeth off the internal gears
and in so doing will void the warranty.
M8 Stainless steel nuts, bolts and washers should be used to secure the base to the mounting surface. Suitable
sealant or a gasket should be used between the camera base and the mounting surface.
Ensure that the 12 pin connector is located into the camera base plug and that the lock ring is tightened. Ensure
that the base compartment containing the 12 way connector is moisture proof. On inverted units it is very
important that the connector area is water tight to prevent water pooling around the connector.
The MiC400 series of PTZ cameras comes with a security attachment point as standard. This should be attached
to a safety chain which in turn should be attached to a secure part of the structure.
Earthing the camera
The camera and camera housing are electrically isolated so the housing should be safety earthed regardless.
This safety earth should be a bonding connection to the camera’s outside case. E.g. one of the securing screws
used for bolting the camera down.
The camera should be earthed at one point only to prevent earth loops and thus hum bars appearing on the
camera picture in the control room.
Connections between the MIC400 and the MIC-PSU using the MIC Composite Cable:
Note: all connections must be made
MIC400 Composite
Cable Wire Colour
Function PSU Terminal
Connector
PSU Terminal ID
marking
Red 15v AC supply HD3-1 Power
Green 15v AC supply return HD3-2 Power
White Camera Rx B HD3-3 RxB
Yellow Camera Rx A HD3-4 RxA
Drain Wire Gnd HD3-5 GND
Blue Camera Tx A HD3-6 TxA
Violet Camera Tx B HD3-7 TxB
Coax Core Video HD3-8 Video
Coax Screen Video Return HD3-9 Vid 0v
Page 3 of 3
BOSCH SECURITY SYSTEMS
Black Tamper Switch HD3-10 Tamp Sw
Orange Wash HD3-11 Wash
Grey 0v Tamper Switch. HD6-1
Brown 0v Wash HD6-2
IR lamp, Heater or
Speaker Option
Grey IR Lamp + or Speaker +
or Heater +
HD6-1 IR +
Brown IR Lamp- or Speaker -
or Heater -
HD6-2 IR -
External Connections to the Power Supply Unit
Please Note:
Cameras are supplied set to address 1, to change the address and configure the camera you will require the
Universal CamSet program and a PC with a serial port and an RS232 to RS485/RS422 adaptor. A PC without a
serial port can use the MIC-USB485 CVTR to connect to the MIC-PSU instead.
TELEMETRY
Signal Function Telemetry Signal Name HD4 or
HD5
RS485 + to camera RXB Pin 1
RS485 – to camera RXA Pin 2
0v from control room. GND Pin 3
RS485 – to control
room.
TXA Pin 4
RS485 + to control
room.
TXB Pin 5
MAINS
Live HD1-1
Neutral HD1-2
Earth HD1-3
VIDEO
Video BNC CN1 Connection
Core Video to Control Room
Screen Video GND to Control Room
Autres manuels pour MIC Series 400
3
Autres manuels Bosch Caméra de sécurité
Bosch
Bosch VG4-322-CTS Manuel utilisateur
Bosch
Bosch LTC 0498 Series Manuel utilisateur
Bosch
Bosch VDI 230 Manuel utilisateur
Bosch
Bosch EX40 Manuel utilisateur
Bosch
Bosch Eyes-Outdoor Manuel utilisateur
Bosch
Bosch V1160 Series Manuel utilisateur
Bosch
Bosch DINION 4000 AN Manuel utilisateur
Bosch
Bosch UNPMS28 Manuel utilisateur
Bosch
Bosch VG4 Series Manuel utilisateur
Bosch
Bosch REG-L1 Manuel utilisateur
Bosch
Bosch NWD-455 FlexiDome Manuel utilisateur
Bosch
Bosch WZ20NXV550‑0 Manuel utilisateur
Bosch
Bosch VG4 Series Manuel utilisateur
Bosch
Bosch NBN-498-21P Manuel utilisateur
Bosch
Bosch AUTODOME IP starlight 5000i IR Manuel utilisateur
Bosch
Bosch NDP-5512-Z30C Manuel utilisateur
Bosch
Bosch EX40 Manuel utilisateur
Bosch
Bosch Dinion LTC0335/20 Manuel utilisateur
Bosch
Bosch MIC400ALBCP13518N Manuel utilisateur
Bosch
Bosch VDC?480 Series Manuel utilisateur
