Bosch EX40 Manuel utilisateur

EX40

Ultra Vandal-Proof Dome Camera

INSTALLATION INSTRUCTIONS

MAN-40-01

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep this instruction.

3. Heed all warnings.

4. Follow all instructions.

5. Clean only with dry cloth.

6. Do not block any ventilation openings. Install

in accordance with manufacturer instructions.

7. Do not install near any heat sources where the

temperature goes above the product rating.

8. Protect the cabling from being walked on or

pinched particularly at connection points and

where they exit from the apparatus.

9. Only use accessories specified by the

manufacturer.

10. Disconnect this apparatus during lightning

storms or when unused for long periods of

time if precautions are not taken to prevent

lightning/electrical damage to the product.

11. Refer all servicing to qualified service

personnel. Servicing is required when the

apparatus has been damaged in a way, such

as internal wiring is damaged, liquid has been

spilled or objects have fallen into the

apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or

has been dropped.

IMPORTANT

For best results, please read this Instruction Booklet prior to

installing the EX40 camera.

WARNING !

CSA Certified / UL Listed CLASS 2 power adaptors must be used

in order to comply with electrical safety standards.

12-24 VDC/VAC (60Hz), 10W

CSA Type 4

CAN/CSA 60065 – 03 + Amd 1

Audio, Video and Similar Electronic Apparatus – Safety Requirements

UL Std No. 60065 - 07

Audio, Video and Similar Electronic Apparatus – Safety Requirements

This Product Has Been Certified By CSA International To Include the

Health Care Facility Requirements Of UL 2044

This installation should be made by a qualified service person and

conform to all local codes.

Bosch will not be responsible for injuries or damages resulting

from the improper installation or use of any camera sold by

Bosch, their agents, distributors or dealers.

EU Directives covered by this declaration:

72/9/EC Low Voltage Directives

89/336/EEC Electromagnetic Compatibility Directive

NOTE: This equipment has been tested and found to

comply with the limits for a digital device, pursuant to

part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. As part of its’

normal operation this device can generate radio

frequency energy and if not installed and used in

accordance with the installation manual may cause

interference to radio communications. However, there

is no guarantee that interference will not occur on a

particular installation. If the device does cause

interference to radio or television reception the user is

encouraged to try to correct the interference by one or

more of the following measures:

1) Fit Ferrite beads on all cable to and from the power

supply box, within the box walls.

2) Route the composite cable between the camera and

the power supply in steel conduit piping over the entire

run of the cable up to and including connection to a

deep conduit base fitted under the camera and a conduit

fitting adaptor in the wall of the PSU box.

3) Contact BOSCH Service Center for further advice.

INDEX – EX40

Page

Description..................................................1

Unpacking...................................................2

Parts List.....................................................2

Items Required for Installation ....................2

Initial Preparations......................................3

Guidelines...................................................3

Section 1. Dome Removal ..........................4

Section 2. Input Power Connections...........6

Section 3. Mounting - Camera Base ...........8

Section 4. Adjustments .............................14

Section 5. Camera Re-Assembly..............21

Section 6. Troubleshooting Guide.............23

Section 7. Template – Mounting Holes .....25

Section 8. General Specifications .............26

DESCRIPTION

The EX40 Hi-Impact Dome Camera has been

engineered for surveillance in hostile

environments. Compact and good looking, the

camera features armour-tough construction for

protection against vandalism or against

accidental damage.

An aluminum housing, CNC-machined from a

billet, with an impact resistant polycarbonate

dome and locking retaining ring, make it

extremely rugged and weather-tight.

For viewing adjustment, the CCD Camera/Lens

Assembly can be fully rotated using a unique

“Pan-Tilt-Twist” (PTT) mounting bracket.

A voltage regulator circuit allows for 12V DC or

24V AC operation, and a range in between, also

providing protection from voltage surge,

transient spikes, and reverse voltage.

UNPACKING

Care should be taken when unpacking the

shipped unit. Check the parts list and confirm all

items have been located. Inspect the equipment

thoroughly to ensure nothing was damaged in

transit.

Contact BOSCH Service Center if a problem is

noted, see rear page of this booklet for contact

numbers.

PARTS LIST (items supplied with unit)

- EX40 Camera Assembly

- half-tint dome bubble (installed)

- Clear dome bubble (spare)

- Installation Instructions booklet

- Plastic bag containing a hex key and one ½

NPT plug wrapped with Teflon tape

- Desiccant pack for moisture absorption (do not

remove)

ITEMS REQUIRED FOR INSTALLATION

(not supplied with unit)

- Philips, Robertson screwdrivers

- Silicone sealant and Teflon sealing tape.

- Mounting screws, etc.

INITIAL PREPARATIONS

Determine the operating voltage at the installation

site. The camera’s Voltage Regulator Board can

accept a 12V DC or 24V AC input.

See Section 2, Input Power Connections.

Determine the optimum location for the camera.

Section 3, Mounting-Camera Base.

All cameras have been tested prior to shipment.

After the wiring has been reconnected, it is

advisable to check the camera’s operation before

installation.

ESD protection – Cameras and circuit boards are

sensitive electronic components. It is

recommended to wear a ground strap to ground

any static charge. (Alternative: touch a grounded

metal plate for at least a minute before proceeding

with any disassembly)

GUIDELINES

The installation of the EX40 camera is explained in

Sections 1 to 5 listed below. It is important that

these steps are followed in sequence:

1. Dome Removal

2. Input Power Connections

3. Mounting - Camera Base

4. Adjustments

5. Camera Re-Assembly

1. DOME REMOVAL

The camera’s dome and its retaining ring must

be removed prior to mounting the camera or

performing any wiring disconnections and re-

connections. The setscrews in the retaining ring

are not tightened in the factory and protrude by

1/8" (3mm) in order for the ring to be rotated.

Refer to Figure 1 - 1 on page 5.

Step 1.1 - Place the camera on a flat surface.

Step 1.2 - Press firmly on the dome with one

hand and rotate the retaining ring in

a counter-clockwise direction with

the other hand. Push against the

protruding setscrews with a finger to

rotate the ring. Do not use a

screwdriver or other metal device.

Step 1.3 - Remove the dome and the retaining

ring. Set them aside.

Autres manuels pour EX40

Table des matières

Autres manuels Bosch Caméra de sécurité

Bosch

Bosch LTC 14xx Series Manuel du propriétaire

Bosch

Bosch LTC 7490 Manuel utilisateur

Bosch

Bosch FCS-8000-VFD-B Manuel utilisateur

Bosch

Bosch FLEXIDOME IP indoor 5000 Manuel du propriétaire

Bosch

Bosch VG4-161-CC0 Manuel utilisateur

Bosch

Bosch FLEXIDOME HD VR Instructions d'utilisation

Bosch

Bosch FLEXIDOME IP 3000i Manuel utilisateur

Bosch

Bosch FLEXIDOME AN outdoor 4000 Manuel utilisateur

Bosch

Bosch FLEXIDOME panoramic 5100i Manuel utilisateur

Bosch

Bosch Eyes-Outdoor Manuel utilisateur

Bosch

Bosch LTC 1321/20 FlexiDome II Manuel utilisateur

Bosch

Bosch MIC400 PTZ Manuel utilisateur

Bosch

Bosch MIC IP fusion 9000i Manuel utilisateur

Bosch

Bosch MIC Series 550 Manuel utilisateur

Bosch

Bosch EX70MNX804-N Manuel utilisateur

Bosch

Bosch VBC?265 Series Manuel utilisateur

Bosch

Bosch FLEXIDOME HD Instructions d'utilisation

Bosch

Bosch MIC Series 400 Manuel utilisateur

Bosch

Bosch DINION IP starlight 6000 HD Manuel utilisateur

Bosch

Bosch VDN-498V06-21S Manuel utilisateur

Bosch

Bosch VJR-A3-IC Manuel utilisateur

Bosch

Bosch SVI-1609-5 Instructions d'installation

Bosch

Bosch VJR SERIES Manuel utilisateur

Bosch

Bosch EX72MNX8V0922-N Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur