Bosch MED17.5.2 Manuel utilisateur

info@chiptuningshop.co.uk

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 1.

1. Description: This probe can be used for programming VAG MED17.5. Bosch ECU`s. It fits in most BDM

positioning frames and is fitted with LED`s for accurate alignment on the ECU. The “Boot” resistors and the

ignition feed can be switched. With this adapter, there is no need to solder at all.

Adapter Overview

A = Serial port connection B = Power Switch ON/OFF

C = Power Jack D = DIP Switches for BOOT Resistors ON/OFF

E = Ignition selection switch:

ON/OFF/K-Line

Since the AVDI requires a permanent connection via a 510 Ohm resistor between the K-Line and 1 V, This switch

has no function in the AVDI version of this probe.

SET TO “K-Line” POS T ON AT ALL T MES

F = Connect to flash tool. G = Connect to serial port on probe (A)

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 2.

2. Handling and Adjustment: MPORTANT - Make sure that the power switch (B) is in the “OFF” position.

The power switch must remain OFF so that the pins are not live, until the probe is correctly aligned and in

contact with the corresponding pins on the ECU. Failure to follow these instructions could result in damage

to the ECU!

Place the probe into the BDM frame retaining bracket and tighten the screws. Attach the adapter cable (G) to

the serial port (A) on the probe and plug the other end (F) into the OBD cable of your flash tool. Connect the

power supply to the probe jack (C), the LED's will now turn on to aid alignment, however the probe does not

power the ECU until the power switch (B) is turned on.

Adjust the ECU on the frame and move the retainer carefully towards the ECU. Ensure that all the pins are in

their designated position.

A diagram showing the location of the connections can be found on page 3.

t is very important, that the retainer is free from backlash and moves smoothly!

3. Reading password: (This step is only necessary for TP8+). Lift up the Boot DIP switches (D) as shown in

the adapter overview on page 1 and set the Ignition switch (E) to the “ON” position, you can now read the

password.

4. Programming the ECU: Push the DIP switches (D) down and set the “Ignition” switch (E) to the “K-Line”

position, then you can proceed with programming over boot mode.

5. Disconnecting: To safely disconnect the probe from the ECU, you must first remove TURN OFF THE

POWER Switch (B). Once the power supply is disconnected it is safe to lift the frame and probe away from

the ECU.

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 3.

The pads marked in red have to make contact with the probe.

Technical alterations reserved!

This product should be operated by competent personnel only. Chiptuningshop Ltd do not accept any responsibility

for damages, direct or consequential caused by improper handling.

Table des matières

Autres manuels Bosch Unité de contrôle

Bosch

Bosch PowerBox PBX 190 Manuel utilisateur

Bosch

Bosch rexroth SB11 Manuel utilisateur

Bosch

Bosch D8125 Mode d'emploi

Bosch

Bosch FLM-420-EOL2W-W Manuel utilisateur

Bosch

Bosch ACS 611 Manuel utilisateur

Bosch

Bosch Rexroth NYM04.1-5PW-NNNN-NY4125 Manuel utilisateur

Bosch

Bosch ICP-COM-IF Manuel utilisateur

Bosch

Bosch Rexroth IM24V Manuel utilisateur

Bosch

Bosch Professional GCY 42 Manuel utilisateur

Bosch

Bosch Rexroth M SED 10 XN Series Manuel utilisateur

Bosch

Bosch Rexroth SM 12 Mode d'emploi

Bosch

Bosch VCU Manuel utilisateur

Bosch

Bosch FM441/CMM 910 Manuel utilisateur

Bosch

Bosch Control 8311 Manuel utilisateur

Bosch

Bosch Rexroth IndraControl VCP 25.2 Manuel technique

Bosch

Bosch MS 3 Sport GT3 Cup Manuel utilisateur

Bosch

Bosch CRR 220 Manuel utilisateur

Bosch

Bosch D9133TTL-E Manuel utilisateur

Bosch

Bosch FLM-I 420-S Manuel utilisateur

Bosch

Bosch CFB 840 Guide de l'utilisateur

Bosch

Bosch IO-BOX32 Manuel utilisateur

Bosch

Bosch ProControl Manuel utilisateur

Bosch

Bosch Rexroth IndraControl XFE 01.1 Series Manuel utilisateur

Bosch

Bosch B426 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur