Bosch ICP-COM-IF Manuel utilisateur

Description of the ICP-COM-IF Module

The ICP-COM-

IF Module allows an isolated connection to be created between the MAP5000 (Interface

Module DE) and an external communicator (for example the AT 2000) via the parallel S1 interface. The

ICP-COM-IF Module offers:

Notes for installation

-The ICP-COM-IF Module can be mounted on the hinged mounting plate or the mounting rails of the

MAP control panel housing.

-A clearance of 15 mm is required on either side for subsequent wiring. Pull to disconnect the

connectors.

-The enclosure of an external transmission unit has to be mounted side by side to the panel enclosure

where the ICP-COM-IF module is mounted.

Mounting

1. Hook the ICP-COM-IF Module carrier plate into the existing breadboard of the

hinged mounting

plate or onto the mounting rails.

2. Use the screw provided to secure the carrier plate to the bottom rail.

•Seven outputs:

The output signals from the MAP Interface Module DE

control the ICP-COM-IF Module relays that provide isolated

changeover contacts (R1 to R7)

•Two inputs:

The inputs ST and R (for the "Communicator fault" or

"Negative confirmation" signals, for instance) can be

controlled via the following:

- isolated contacts

- C points (isolated via optocouplers)

Technical specifications

Rated voltage +10 to +28 V DC

Rated current

67 mA at 28 V or 180 mA at 10 V

Relay contacts rating 3 A/120 V AC, 3 A/28 V DC

Temperature range −25 °C to +55 °C

Weight 198 g

Dimensions (L x W x H) 132 mm x 85 mm x 20 mm (5.2 inches x 3.3

inches x 0.8 inches)

Bosch Sicherheitssysteme GmbH

Robert

-Bosch-Ring 5

85630 Grasbrunn

Germany

www.boschsecurity.com

32014/11

ICP-COM-IF

Installation guide

VdS class C G 111040

EN 50131

-2-6 Grade 3

Jumper settings

The inputs ST and R can be controlled via the following:

•isolated contacts

•C points (isolated via optocouplers)

To control the inputs via external "isolated contacts" or "C points", the jumpers must be

connected as follows:

Input Jumper setting Description

ST Control via isolated contact (factory default)

R Control via isolated contact (factory default)

ST Control via C point

R Control via C point

Relays

Output/input

Stand-by mode

Activation with

Output for the communicator alarm line ML1

Summary alarm

Output for the communicator alarm line ML2

Off

Duress

Output for the communicator alarm line ML3

Off

Holdup

Output for the communicator alarm line ML4

Intrusion/Tamper

Output for the communicator alarm line ML5

Summary Trouble

Output for the communicator alarm line ML6

Off

Fire

Output for the communicator alarm line ML7

Off

Armed (any area)

Input from external communicator

Communicator fault

Input from external communicator

Negative confirmation

ssysteme GmbH, 2014

32014/11

Relay 1

AT 2000

Relay 2

Remote communicator, for example the AT 2000

R1A

R1B

R1C

C1C

ML7

ML6

ML5

ML4

ML3

ML2

ML1

AT 2000 programming

•

Relay 1: "Continuous activation", stand-by "on"

•

Relay 2: "5 seconds", stand-by "off"

•

ML1–ML7: Conventional Lines Intrusion

Relay 2:

Negative

confirmation

Relay 1:

Communicator fault

C1B

C1A

ICP

-COM-IF

MAP Interface Module DE

The ribbon cable is

ttached to the MAP

Inter

face Module DE

Parallel S1 in-

terface

Red

marking at

top

The size of the terminal resistors (RE) to be looped in

depends on the communicator (for example 10 k for the AT 2000).

Pull to disconnect the connectors.

ML2

ML3

ML4

ML6

ML5

Red

arking

at top

Autres manuels Bosch Unité de contrôle

Bosch

Bosch Rexroth BTV 16 Manuel technique

Bosch

Bosch Rexroth 3DREP 6 XE Series Manuel utilisateur

Bosch

Bosch KTS Truck Manuel utilisateur

Bosch

Bosch RTM 430 Guide de configuration

Bosch

Bosch MU 100 Manuel utilisateur

Bosch

Bosch D8125 Guide de démarrage rapide

Bosch

Bosch C900TTL-E Manuel utilisateur

Bosch

Bosch B520 Instructions d'utilisation et d'entretien

Bosch

Bosch MC 400 Manuel utilisateur

Bosch

Bosch rexroth M1-16 Series Manuel utilisateur

Bosch

Bosch Rexroth MKK 12-40 Manuel utilisateur

Bosch

Bosch MM100 Manuel de service

Bosch

Bosch rexroth Automax 100 Manuel utilisateur

Bosch

Bosch Rexroth IndraControl S67 Series Manuel utilisateur

Bosch

Bosch Rexroth NYS04.1-ST-01-LMS-SERCOS-NY4078 Manuel utilisateur

Bosch

Bosch MU 100 EMS Manuel utilisateur

Bosch

Bosch D8125 Mode d'emploi

Bosch

Bosch CFB 840 Guide de l'utilisateur

Bosch

Bosch BEA 030 Manuel utilisateur

Bosch

Bosch GCY 30-5 T Instructions de montage

Bosch

Bosch MAP Control Center IUI-MAP0001-2 Manuel utilisateur

Bosch

Bosch KTS 5 Series Manuel utilisateur

Bosch

Bosch Rexroth BVD 52 Series Manuel utilisateur

Bosch

Bosch SE352 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur