Bosch D113 Manuel utilisateur

Battery Lead Supervision Module

D113

en Installation manual

Battery Lead Supervision Module Notices | en 3

Bosch Security Systems, Inc. Installation manual 2020.03 | 10 | F.01U.036.374

1 Notices

These instructions cover the installation of the Bosch Security Systems, Inc. (hereinafter,

Bosch) D113 Battery Lead Supervision Module in a system controlled by a Bosch 12VDC

control/communicator. This module may be used with other panels when referenced in the

panel’s installation/operation instructions.

Warning!

Follow these instructions to avoid personal injury and damage to equipment.

Install, test and maintain the module according to these instructions, NFPA codes, local codes,

and the authority having jurisdiction (AHJ). Failure to follow these instructions can result in

failure of a detector to initiate an alarm event. Bosch Security Systems, Inc. is not responsible

for improperly installed, tested or maintained devices.

NFPA72 requires that you perform a complete system wide functional test following any

modifications, repair, upgrades or adjustments made to the system’s components, hardware,

wiring, programming and software/firmware.

UL Listed

This product is UL Listed for the following certifications:

– UL864 8th Edition

– UL985 6th Edition

4en | Description Battery Lead Supervision Module

2020.03 | 10 | F.01U.036.374 Installation manual Bosch Security Systems, Inc.

2 Description

This module provides supervision of the battery lead connection between the module and one

or two batteries in a system controlled by a Bosch 12VDC FACP or control/communicator.

This module may be used with other panels when referenced in the panel’s installation/

operation instructions. The module meets NFPA 72 requirements for battery lead supervision

for fire alarm control panels (FACPs).

The following products are compatible with this module:

Category Product

Batteries D126 Standby Battery (12V, 7Ah)

D1218 Battery (12V, 18Ah)

G Series control panels B9512G, B8512G1

Legacy control panels D7212GV4, D7212GV3, D7212GV2, D7212G

1These control panels are listed for UL 864 10th edition.

Battery Lead Supervision Module Trouble and Supervisory conditions | en 5

Bosch Security Systems, Inc. Installation manual 2020.03 | 10 | F.01U.036.374

3 Trouble and Supervisory conditions

When the module detects a disconnected battery lead, it creates a shorted condition on the

supervising zone or point. Program the panel according to the appropriate programming guide

to generate a trouble response to a shorted condition on the loop. Reset the module by

reconnecting the battery lead and clearing the trouble condition at the FACP.

Caution!

When two batteries are connected in parallel to a FACP with on‑board battery lead

supervision, the panel cannot detect a single missing battery. Use this module in all fire

applications using two parallel batteries.

Notice!

The module will also indicate a trouble condition if one or both of the batteries are connected

with their polarity reversed. To reset, disconnect the batteries and reconnect properly.

6en | Installation Battery Lead Supervision Module

2020.03 | 10 | F.01U.036.374 Installation manual Bosch Security Systems, Inc.

4 Installation

Removing power from the FACP

Caution!

Before installing the module in an existing system, inform the Central Station and the Local

Authority and disconnect all power to the control panel.

Remove AC power from the system at the dedicated 120VAC breaker and remove the standby

battery power before making or removing any connections to the FACP.

Mounting the module in the FACP enclosure

The module mounts to the side of the enclosure using the supplied plastic standoffs and

screws.

A snap track is included for enclosures that do not have a three‑hole mounting pattern on the

interior side walls. To mount the snap track, remove the backing from the tape, line the

hole(s) in the snap track up with the existing hole(s) in the enclosure, and firmly press it onto

the side of the enclosure. After mounting the snap track, secure it to the enclosure with at

least one screw and nut. Then mount the module to the snap track.

Wiring the module to the FACP

Caution!

Do not cross polarity. Red wires connect to the positive battery terminals. Black wires

connect to the negative battery terminals.

Use the following procedure when wiring the module to a FACP:

1. Connect the RED wire lead provided with the module to the positive (+) battery terminal

on the FACP.

2. Connect the other end of the RED wire lead to Terminal1 (CHRG+) on the module.

3. Connect the BLACK wire lead provided with the module to the negative (-) battery

terminal on the FACP.

4. Connect the other end of the BLACK wire lead to Terminal4 (CHRG-) on the module.

5. Connect the GREEN wire lead provided with the module to the zone or point input with

the EOL resistor on the FACP.

6. Connect the other end of the GREEN wire lead to Terminal2 (SUPV) on the module.

7. Connect the ORANGE wire lead provided with the module to the auxiliary power positive

terminal on the FACP or the auxiliary power supply.

8. Connect the other end of the ORANGE wire to Terminal3 (VAUX+) on the module.

Battery Lead Supervision Module Installation | en 7

Bosch Security Systems, Inc. Installation manual 2020.03 | 10 | F.01U.036.374

Figure4.1: Wiring the module

1 To Batt Pos (+) 4 To Comm

2 To Batt Neg (-) 5 To Input Point (Trouble)

3 To Aux Power (+) 6 EOL

Wiring the module to the battery leads

Use the following procedure when wiring the module to the battery leads:

1. Connect the positive (+) battery lead from Battery1 to Terminal5 (BAT1+) of the module.

2. Connect the negative (-) battery lead from Battery1 to Terminal6 (BAT1-) of the module.

3. Connect the positive (+) battery lead from Battery2 to Terminal7 (BAT2+) of the module.

4. Connect the negative (-) battery lead from Battery2 to Terminal8 (BAT2-) of the module.

Module terminal Battery connection

8 Battery 2 NEG (-)

7 Battery 2 POS (+)

6 Battery 1 NEG (-)

5 Battery 1 POS (+)

Tab.4.1: Module terminals to battery connections

1. If the module is supervising a single battery, connect the battery leads to Terminals5 and

6 and connect the jumper wires to Terminals7 and 8, as shown in the following Figure.

8en | Installation Battery Lead Supervision Module

2020.03 | 10 | F.01U.036.374 Installation manual Bosch Security Systems, Inc.

Figure4.2: Jumper locations for single‑battery installations

Restoring power to the FACP

Close the 120VAC dedicated breaker that controls the power input to the FACP and

reconnect the standby batteries.

Battery Lead Supervision Module Specifications | en 9

Bosch Security Systems, Inc. Installation manual 2020.03 | 10 | F.01U.036.374

5 Specifications

Electrical

Voltage (input range) 10.2V min to 13.9V max

Voltage (battery) 12V nominal

Current draw145mA

1 For battery calc, use 45mA for alarm and 45mA for standby

10 | Specifications Battery Lead Supervision Module

2020.03 | 10 | F.01U.036.374 Installation manual Bosch Security Systems, Inc.

Table des matières

Autres manuels Bosch Unité de contrôle

Bosch

Bosch Rexroth IMpdp Manuel utilisateur

Bosch

Bosch FLM-420-O2-D Manuel utilisateur

Bosch

Bosch Rexroth WMM6 Series Manuel utilisateur

Bosch

Bosch MS 3 Sport GT3 Cup Manuel utilisateur

Bosch

Bosch AMC2-4WE Manuel utilisateur

Bosch

Bosch Conettix B444-A Manuel utilisateur

Bosch

Bosch RM2-DP12 Instructions d'utilisation et d'installation

Bosch

Bosch ETT 223 Manuel utilisateur

Bosch

Bosch Rexroth NYCe 4000 Manuel utilisateur

Bosch

Bosch Rexroth H-4WEH...XE Series Manuel utilisateur

Bosch

Bosch C900TTL-E Manuel utilisateur

Bosch

Bosch Rexroth VKK Manuel utilisateur

Bosch

Bosch LSN 0300 A Manuel utilisateur

Bosch

Bosch DCU 220 Guide de configuration

Bosch

Bosch DCU 220 Guide de configuration

Bosch

Bosch AMC2 4W-EXT Manuel utilisateur

Bosch

Bosch KTS 5a Series Manuel utilisateur

Bosch

Bosch Rexroth M4-12 Mode d'emploi

Bosch

Bosch D9133TTL-E Manuel utilisateur

Bosch

Bosch DS7400 Manuel utilisateur

Bosch

Bosch Rexroth 4WS2EM 10 Series Manuel utilisateur

Bosch

Bosch FLM-420-EOL4W-D Manuel utilisateur

Bosch

Bosch MKK-040 Manuel utilisateur

Bosch

Bosch KTS 5 Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur