Bosch GWH 2400 ES NG Manuel utilisateur
Installation manual
Pipe Cover
For Bosch Aquastar Models: GWH 2400 ES, GWH 2700 ES
For Bosch ProTankless Models: GWH 715 ES, GWH C 800 ES, GWH C 920 ES, GWH C 920 ESC
For Bosch THERM Models: 830 ES, 940 ES, 940 ESO, C 950 ES, C 1050 ES, C 1210 ES, C 1210 ESC
2| Pipe Cover Installation Manual
Pipe Cover Installation Manual | BTC 710003301 C | 06.2011
Technical specifications are subject to change without prior notice
Pipe Cover Installation Manual | BTC 710003301C | 06.2011 Technical specifications are subject to change without prior
| 3
Pipe Cover Installation Manual
Table of Contents
1 Introduction 4
1.1 Items included with Pipe Cover kit 4
1.2 Tankless Water Heater compatibility 4
2 Installation 5
4| Pipe Cover Installation Manual
Pipe Cover Installation Manual | BTC 710003301 C | 06.2011
Technical specifications are subject to change without prior notice
1 Introduction
1.1 Items included with Pipe Cover kit:
See Figure 1
• Front Panel (1)
• Right side panel (1)
• Left side panel (1)
• Bottom Panel (1)
• Machine screws (10)
• Self tapping screws #8 (4)
Front panel
Right side panel
Left side panel
Bottom panel
Rear
Notch
Notch
Front
23.5"
Fig. 1 Pipe Cover kit components overview
1.2 Tankless Water Heater compatibility
The Pipe Cover kit is compatible with the following Bosch
tankless water heaters:
• GWH 2400 ES (part number: AQPCES)
• GWH 2700 ES (part number: AQPCES)
• GWH 715 ES (part number: PTPCES)
• GWH C 800 ES (part number: PTPCES)
• GWH C 920 ES (part number: PTPCES)
• GWH C 920 ESC (part number: PTPCES)
• 830 ES (part number: PTPCES)
• 940 ES/ESO (part number: PTPCES)
• C 950 ES (part number: PTPCES)
• C 1050 ES (part number: PTPCES)
• C 1210 ES/ESC (part number: PTPCES)
The pipe cover cannot be used with any Bosch
GWH 635 ES, GWH 635 ESO, AQ 250 SX,
AQ 250 SXO, GWH 2400 E, GWH 2400 EO models
Pipe Cover Installation Manual | BTC 710003301C | 06.2011 Technical specifications are subject to change without prior
| 5
Pipe Cover Installation Manual
2 Installation
1. Ensure all items listed in Section 1.1 are complete.
2. Water heaters listed in Section 1.2 with date codes
FD984 and later are equipped with screw holes for the
pipe cover. The FD code is the first 3 numbers in the
appliance’s serial number (see Fig.2, pos. A). For all
earlier models, use the bottom panel of the pipe cover
as a template to drill four ⁹⁄₆₄"diameter holes into the
bottom of the water heater. (See Fig. 3).
ASerial number
984 01011
Fig. 2 Rating plate sticker with serial number (right side of heater)
3. For heaters without pre-drilled holes, place the water
heater on its back with the front cover removed. Position
bottom panel of pipe cover over the bottom of the water
heater being sure to line up flush where indicated (See
Fig. 4). Once aligned, mark the four holes in the bottom
panel for drilling. Remove bottom panel and drill four
⁹⁄₆₄"diameter holes into the bottom of the water heater.
CAUTION:
Drill carefully ensuring not to damage components
inside of the water heater casing
Front
Rear
GAS
HOT COLD
Bottom
of water
heater
Bottom
panel of
pipe
cover
Fig. 3 Using bottom panel as drill template
Heater Front
Heater Rear
GAS
HOT COLD
Hole
diameter
⁹/₆₄" x 4
Bottom
panel
must be
flush to
here
Bottom
panel
must be
flush to
here
Fig. 4 Drill template alignment to water heater bottom
3. Hang the water heater following the appliance’s
installation instructions.
4. Complete the pipework. It is recommended to install
an electrical junction box with an electrical outlet inside
the pipe cover.
6| Pipe Cover Installation Manual
Pipe Cover Installation Manual | BTC 710003301 C | 06.2011
Technical specifications are subject to change without prior notice
5. Install the water heater cover. Tighten the 2 screws at
the bottom left and right.
6. Install the left side panel of the pipe cover with the right
angle bends facing the wall and down. Tighten the screws
to hand tight, then back out 1 turn. See Fig. 5.
Fig. 5 Left side panel installation
7. Install the right side panel the same way. Tighten the
screws to hand tight, then back out 1 turn.
8. Using four machine screws, mount the bottom panel on
the inside of the flanges with the opening facing the
wall. See Fig. 6.
Right side panel
Bottom panel
Rear
Front
Left side panel
Fig. 6 Bottom panel installation
9. Ensure all panels are straight and plum.
10. Finish installing the pipe work inside the pipe cover.
The drain from the relief valve and the condensate drain
(condensing models only) must extend below the pipe
cover.
11. Fit the front panel with the 2 notches facing up. See
Fig. 7.
Front panel
Notch
Notch
Fig. 7 Front panel
Pipe Cover Installation Manual | BTC 710003301C | 06.2011 Technical specifications are subject to change without prior
| 7
Pipe Cover Installation Manual
12. The upper radius of the front panel must be fitted behind
the water heater’s cover for proper installation (Fig.
8, pos.1). If necessary adjust the side panels to allow
the front cover to fit properly. Once top of front panel
is fitted behind the water heater’s cover, swing bottom
of front panel inwards (Fig.8, pos. 2). Ensure that the 4
screw holes line up with the threaded inserts on the side
panels. Secure using four machine screws.
Pipe Cover
side panel
Wall
1
2
Water
Heater
side
Pipe Cover
front panel
Water
Heater
cover
Fig. 8 Front panel installation
13. When fitting properly, tighten the attachment screws
at the bottom of the water heater to hand tight. Then
install and tighten screws for the front panel of the pipe
cover. This installation is now complete (See Fig. 9).
14. On outdoor installations, install the outdoor vent
conversion cap in accordance with the installation
instructions included in the outdoor kit packaging.
Fig. 9 Completed pipe cover installation
Bosch Thermotechnology Corporation
50 Wentworth Avenue
Londonderry, NH 03053
Tel.: 800-283-3787
Fax: 603-584-1687
www.bosch-climate.us
Bosch Thermotechnology Corporation reserves the right to
make changes without notice due to continuing engineering
and technological advances.
BTC 710003301 C
Autres manuels pour GWH 2400 ES NG
2
Ce manuel convient aux modèles suivants
17
Table des matières
Autres manuels Bosch Accessoires
Bosch
Bosch Rexroth 3 842 547 200 Manuel utilisateur
Bosch
Bosch GPL 3 Professional Manuel utilisateur
Bosch
Bosch PFB3060 Manuel utilisateur
Bosch
Bosch CISS Manuel utilisateur
Bosch
Bosch PLS Manuel utilisateur
Bosch
Bosch ISC-SK10 Manuel utilisateur
Bosch
Bosch CANbus LCD Manuel utilisateur
Bosch
Bosch Rexroth MM7.10 Manuel utilisateur
Bosch
Bosch Blue Line P1 Manuel utilisateur
Bosch
Bosch DS161 Manuel utilisateur
Bosch
Bosch Rexroth TS 1 5.3 Manuel utilisateur
Bosch
Bosch Rexroth CIMS Mk IV Manuel utilisateur
Bosch
Bosch LTC 9083/01 Manuel utilisateur
Bosch
Bosch PSJ120S Instructions de montage
Bosch
Bosch ISC-CDL1-WA15G Manuel utilisateur
Bosch
Bosch Blue Line Q1 Manuel utilisateur
Bosch
Bosch REXROTH BS 1 Manuel utilisateur
Bosch
Bosch ISW-EN1247 Manuel utilisateur
Bosch
Bosch DS415i Manuel de service
Bosch
Bosch KTR SERIES Manuel utilisateur
