Bodet Profil TGV 950 Manuel utilisateur

Clock

Prol TGV 950

Prol TGV 970

AFNOR / IRIG B receiver

RADIO receiver

INSTALLATION AND OPERATING INSTRUCTIONS

1 rue du Général de Gaulle

49340 TRÉMENTINES

FRANCE

Tél. : 02 41 71 72 33

www.bodet-time.com

Upon receipt, always check the product for damage during shipment. If any is found, you may le a damage

claim with the carrier

Réf.: 607100 F

Table of contents

I - INITIAL VERIFICATION 3

1.1 Unpacking the clock 3

1.2 Cleaning 3

II - DISCLAIMER 4

III - INSTALLATION 4

3.1 Mechanical installation 4

3.2 Setting in operation 5

3.2.1. AFNOR/IRIG-B receiver clock 5

3.2.3. Radio receiver clock 6

3.3 Setting the antenna 7

IV - SAFETY INSTRUCTIONS 8

IV - TECHNICAL FEATURES 9

TGV 950 9

TGV 970 10

V - WHAT TO DO IF...? ...CHECK. 11

I - INITIAL VERIFICATION

Thank you for choosing a BODET clock. This product has been carefully designed for your

satisfaction based on ISO9001 quality requirements. We advise you to read this manual

thoroughly before attempting to manipulate the clock.

Keep this booklet during all the life of your clock, so that you can refer to it each time it is

necessary.

Bodet accepts no responsibility for accidents resulting from any use not conforming with the

above provisions.

Any modication to the product will invalidate the warrantee.

1.1 Unpacking the clock

Unpack with caution and check the contents of the packaging. It must contain :

- the TGV clock,

- for radio synchronised models : the antenna,

- a key to open the casing,

- an antistatic cleaning kit,

- this booklet.

Versions : a label inside the clock species what model the clock is :

AFNOR HMS or AF HMS = the clock is a receiver driven by : a master clock that sends

AFNOR NFS-87500A coded time messages or a radio receiver antenna, and powered by

240 VAC, with a servo second hand.

1.2 Cleaning

Use an antistatic product of similar type to the one shipped in the original packaging. Never use

alcohol, acetone or any other solvent liable to damage the casing and glass on your clock.

II - DISCLAIMER

Bodet accepts no responsibility for accidents resulting from any use not conforming with the

above provisions.

Any modication to the product will invalidate the warrantee.

Read the chapter «Safety instructions» in this manual before installing this equipment.

III - INSTALLATION

3.1 Mechanical installation

Select the place where the clock will be installed while making sure that radio reception is

correct for radio synchronisation models.

TGV 950 clock

TGV 970 clock

230

322

162

Ø 500

Ø 140

Ø 230

Ø 270

24 trous Ø 8,20

322

163

360

180

163

Ø 700

360

180

360

Ø 470

24 trous Ø 11

sur un Ø430

■Open the clock by giving the screw a quarter turn

with the key (5).

■On the TGV950 clock, remove the 2 locking

srews (3) (provided for the transit).

■Pull the whole dial (1) towards you.

■The hinge arm opening system ensures a fast

and secure maintenance of the lighting without

having to put the front part of the clock on the

ground.

■ Hang the clock and x it with screws, without

locking it, after you have put the wires through

the waterproof pressure joints (4).

3.2 Setting in operation

3.2.1. AFNOR/IRIG-B receiver clock

■ Switch o󰀨 the circuit breaker involved.

■Connect the mains 230 V +/-10% 50 Hz to the

terminal (6) (Live, Neutral and Earth wires; section

1.5 mm² to 2.5 mm² and bare on 5 mm). The mains

cable must be oversheathed up to the terminal.

■Attach the 3 wires (Live, Neutral an Earth) with the

cable tie.

■A double/reinforced electrical insulation must be

assured between the mains cable and the SELV

wires.

■Connect the time signal network to the terminals 1

and 2 of the AFNOR receiver card.

■Check that the dip switch (16) is pushed to the

AFNOR position.

■Check that the battery is connected to the terminal (2) of the electronic card.

■Lock the clock.

■Push the dip switch (15) to the ON position.

■Close the clock.

■Power the clock.

Operating principle of AFNOR receiver clock :

■When switching on power supply, hands are set at

12.00 until the correct reception of the time signal

is achieved. After 3 successive coherent AFNOR

time signals are received, the clock starts and

automatically get on time with fast impulses.

AFNOR

input

■During 1 hour without reception of the time signal the clock operates with its own time basis. If

the signal recovery is achieved within this hour, the clock will be resynchronised automatically.

After 1 hour the clock is reset and hands are set on position 12.00.

■Without power supply 230V the clock operates with its battery during 1 hour. After 1 hour

without time signal reception or if the battery voltage drops down, hands are set position 12.00

until power supply recovery.

■The synchronous second hand witch is powered by the main 12V 50Hz, will stop immediately.

3.2.3. Radio receiver clock

■ Switch o󰀨 the circuit breaker involved.

■Connect the mains 230 V +/-10% 50 Hz to the

terminal (6) (Live, Neutral and Earth wires; section

1.5 mm² to 2.5 mm² and bare on 5 mm). The mains

cable must be oversheathed up to the terminal.

■Attach the 3 wires (Live, Neutral an Earth) with the

cable tie.

■A double/reinforced electrical insulation must be

assured between the mains cable and the SELV

wires.

■Connect the two wires of the antenna to the

terminals 4 and 5 of the electronic card.

■Check that the dip switch (16) is in receiver position.

■Check that the battery is connected to the terminal (2) of the electronic card.

■Lock the clock.

■Push the dip switch (15) to the ON position.

■Close the clock.

■Power the clock.

Operating principle of radio receiver clock

■When switching on power supply, hands are set

at 12.00 until the correct reception of the time

signal is achieved. After 3 successive coherent time signals are received, the clock starts and

automatically get on time with fast impulses.

■Once the clock is synchronised, it operates with its own time basis. If the signal is back within

this period, the clock set itself automatically.

■Without power supply 230V the clock operates with its battery during 1 hour. After 1 hour

without time signal reception or if the battery voltage drops down, hands are set position 12.00

until power supply recovery.

■The synchronous second hand witch is powered by the main 12V 50Hz, will stop immediately.

Input 162

3.3 Setting the antenna

For radio synchronised clocks :

The best reception conditions are outside

buildings or near windows.

Positioning the antenna (perpendicular to the

direction of the transmitter) improves

reception.

The antenna must not be placed on a metal

support.

As for any radio system, a building with metal

structures can cause interference in the

reception of the signal.

Computers, television sets and electrical

appliances can also cause interference that

disrupt the reception of the radio message.

- Unlock the antenna from its support.

- Fix the support with the screw supplied and lock the antenna again.

Beware : in a double face system. So as not to cause interference

between the 2 antennas, the latter must be xed at least one metre

away from each other.

ALS

IV - SAFETY INSTRUCTIONS

Installation and maintenance of this equipment must be carried out by qualied personnel only.

Electrical installation must comply with current standard CEI 364. (NF C15-100 in France for

example).

This is a class I product.

Do not apply the power before installation.

The mains supply for the clock must include a circuit breaker rapidly accessible. It must break

neutral and phase simultaneously.

This circuit breaker must be switched o󰀨 during maintenance operations.

Use cable ties to attach the mains cable (see section “Installation).

Caution: use of an unqualied battery may present a risk of explosion. Waste battery should be

disposed so that they can be recycled.

LED lights can be hazardous to the eyes.

The LED lighting systems are less energy consuming than other types of lighting and have

lifetimes much longer.

Partly because of the limited nature of the surface emission, LEDs have luminances at least

1000 times higher than those of a traditional lighting source. The level of direct radiation from

such sources exceeds the level of visual discomfort.

Our clocks are designed so that there is no direct light, and thus no risk. However, it is

recommended to switch o󰀨 the lighting system before opening the clock for maintenance.

IV - TECHNICAL FEATURES

Power supply : 230 Volt 50 Hz ±10%,

Operating temperatures : -25°C to +50°C,

Protection index : IP54.

TGV 950

Readability : 40m.

Weight : 8 kg.

Lighting consumption : 14 W.

Dimensions :

TGV 970

Readability : 50m.

Weight : 16 kg

Lighting consumption : 20 W.

Dimensions :

322

162

Ø 500

Ø 140

Ø 230

Ø 270

24 trous Ø 8,20

Double face

clock

Single face

clock

Disk for hanging bracket or

suspension on a chain

322

163

360

180

Ø 700

180

360

Ø 470

24 trous Ø 11

sur un Ø430

Double face

clock

Single face

clock

Disk for hanging bracket or

suspension on a chain

Autres manuels pour Profil TGV 950

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bodet Horloge

Bodet

Bodet Style 5 Seconde Manuel utilisateur

Bodet

Bodet Sigma Mod Instructions et recettes

Bodet

Bodet Style Mondiale Manuel utilisateur

Bodet

Bodet Profil 750 Manuel utilisateur

Bodet

Bodet Cristalys Manuel utilisateur

Bodet

Bodet Profil 930 Manuel utilisateur

Bodet

Bodet 10 Manuel utilisateur

Bodet

Bodet Profil 930 Manuel utilisateur

Bodet

Bodet 5 Seconde Manuel utilisateur

Bodet

Bodet Style 5 Seconde Manuel utilisateur

Bodet

Bodet Style 12 Manuel utilisateur

Bodet

Bodet Style 5S Manuel utilisateur

Bodet

Bodet Profil 960 Manuel utilisateur

Bodet

Bodet Style 12 Manuel utilisateur

Bodet

Bodet Profil 730 Manuel utilisateur

Bodet

Bodet Cristalys 7 Manuel utilisateur

Bodet

Bodet DHF/DCF Interface Manuel utilisateur

Bodet

Bodet Profil 750 Manuel utilisateur

Bodet

Bodet BTX6015 Manuel utilisateur

Bodet

Bodet Profil 930 Manuel utilisateur

Bodet

Bodet Cristalys 14 Manuel utilisateur

Bodet

Bodet HMS LED 10 Manuel utilisateur

Bodet

Bodet Profil 750 Manuel utilisateur

Bodet

Bodet Profil 930 L Manuel utilisateur

Manuels Horloge populaires d'autres marques

Silicon Laboratories

Silicon Laboratories SI5324 Manuel utilisateur

Heathkit

Heathkit GC-1005 Manuel utilisateur

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuel utilisateur

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuel utilisateur

ALGE-Timing

ALGE-Timing ASC3 Manuel utilisateur

Nixie Clock

Nixie Clock Divergence Meter Manuel utilisateur

La Crosse Technology

La Crosse Technology WS-8256-AL Manuel utilisateur

Mini Gadgets

Mini Gadgets MCPro Manuel utilisateur

Casio

Casio TMR-200 Manuel utilisateur

Progetti

Progetti ILTEMPOSTRINGE Manuel

BVItech

BVItech BV-101 Manuel utilisateur

Progetti

Progetti KALIMERO Manuel

La Crosse Technology

La Crosse Technology WT-3141b Manuel

La Crosse Technology

La Crosse Technology W86531 Manuel utilisateur

Sharp

Sharp SPC900 Manuel utilisateur

La Crosse Technology

La Crosse Technology 404-50447 Manuel utilisateur

Datexx

Datexx DF0063 Manuel utilisateur

LG LEC-005 Manuel utilisateur