Blendtec Stealth Manuel utilisateur

blendtec.com/commercial | Stealth

Owner’s Manual

Section 1: Important Safeguards 1

Section 2: Component Overview 3

Section 3: Unpacking 5

Section 4: Installation 6

Section 5: Operation 8

Section 6: Troubleshooting 17

Section 7: Cleaning 19

Section 8: Warranty and Service 21

Appendix: Countertop Hole Template 26

Table of Contents

Section 1: Important Safeguards

Read all instructions carefully before using your Blendtec®Stealth®machine.

1.1 Safety Certiﬁcation

The Stealth blender and accessories are certiﬁed by ETL to UL standard (ANSI/UL

763) Issue: 2012/01/31 and to CSA standard C22.2 #195 Issue: 1987/03/01.

1.2 Health Certiﬁcation

The Stealth blender and accessories are certiﬁed by NSF International.

1.3 Avoiding Contact with Moving Parts

Keep hands, hair, and clothing away from all moving parts. Keep all utensils away

from the drive socket and blender blades during operation. Never put your hands

in the blender jar or add substances by hand when the blender is operating. Never

place the jar in the drive socket if the blender motor is operating. Do not rock

the blender when it is operating. Keep the blender jar straight up until operation

is complete. These precautions will prevent personal injury and damage to the

blender.

1.4 Power Cord Precautions

Do not operate the machine if the plug or damaged power is damaged. If the

cord is damaged, it must be replaced by Blendtec or one of its qualiﬁed service

agents in order to avoid a hazard. Do not let the cord hang over the edge of the

work surface. Never use an extension cord with the unit. Unplug the blender before

removing the sound enclosure, changing the blender location, or cleaning.

1.5 Power Cord Receptacle

Ensure the electrical outlet that powers the blender is always accessible.

1.6 Electrical Circuit Precautions

Do not use other electrical equipment on the same circuit as the blender; doing so

may overload the circuit and damage the blender electronics or blow the circuit

protection.

1.7 Water Damage and Abuse

It is critical to prevent liquids from entering the motor base. The motor base has

been designed to deﬂect liquids from entering. However, in some instances of

heavy spillage or a lack of appropriate cleaning procedures (see Section 7), liquids

may enter the motor housing. It is important to promptly clean up all spills on the

motor, around the counter, and under the sound enclosure base (if used). Failure to

do so may result in liquids being pulled into the motor, which will lead to premature

failure. This cause of failure is considered abuse and is not covered under the

warranty.

1.8 Blender Blade

The blender blade is sharp—handle it carefully.

1.9 Materials Not Appropriate for Use in the Blender Jar

Never put metal (for example, utensils), rocks, or other hard materials in the blender

jar. Such materials can cause injury and damage. Damage caused by such items is

not covered under the warranty.

1.10 Use of the Blender Lid

To prevent blender ingredients from ﬂying out of the jar and making a mess, always

secure the lid on the blender jar before blending.

1.11 Attachments Not Sold by Blendtec

Do not operate the blender with any attachments not sold by Blendtec. Using such

attachments with the blender will void the warranty and may cause ﬁre, electric

shock, or injury.

1.12 Caution about Touching the Metal Base After Extensive Use

The metal base of the blender may become hot after numerous cycles. Avoid

touching the base after extensive use.

1.13 Cleaning the Motor Base

Never clean the motor base with a water jet or submerge the base in water. Doing

so will void the warranty.

1.14 Service and Adjustments of Motor

The blender motor does not contain user-adjustable or user-serviceable parts. All

service and adjustments must be made by a Blendtec qualiﬁed service agent.

Removing the motor base cover or servicing the blender will void the warranty.

1.15 Unit Malfunction and Damage

If the blender malfunctions, stop using the blender. Call Blendtec customer service

at 1-800-BLENDTEC (US customers) or one of Blendtec’s qualiﬁed service agents

(international customers). If the blender is dropped or damaged in any way, return

the blender to Blendtec customer service (US customers) or a Blendtec qualiﬁed

service agent (international customers) immediately for examination, repair,

electrical or mechanical adjustment, or possible replacement.

Save these instructions for future reference.

Section 2: Component Overview

2.1 Blender Motor Base

2.2 Control Surface

The illuminated, capacitive-touch control surface features an intuitive, simple-to-use

interface and ﬁne-tuned blending controls.

Motor Housing

Houses all

components and

optimizes sound

and airﬂow for

cooler, quieter

operation. Never

remove the motor

housing.

Blender Motor

Contains the

machinery that

runs the blender,

including the

electric motor and

drive train.

Control Surface

Capacitive-touch

LED interface

with intuitive

control icons and

information screen.

Drive Socket

Direct drive

coupling with the

jar blade shaft.

The socket has a

lifetime warranty.

Scroll (visible in programming mode)

Power

Mode

Slider Control Bar

Preprogrammed Cycle Buttons

Cancel/Exit

Pulse

Select (visible in programming mode)

USB Port

Connects to a ﬂash

memory device

for quick, easy

programming.

Figure 1. Motor Base

Figure 2. Control Surface

2.3 Blender Jar Assembly

2.4 Sound Enclosure

The sound enclosure has been engineered to reduce the noise of blender

operation, giving you the quietest blending experience available.

2.5 Power Speciﬁcations

The Blendtec Stealth has the power speciﬁcations listed below.

Model (110/120 Volts) Amps Watts

Stealth above counter (CQB) 15 1800

Stealth in counter (IQB) 15 1800

Blendtec 110/120-volt blenders must be protected by a dedicated 20-amp circuit

breaker or fuse.

Jar

Made from safe, durable, BPA-free

Eastman Tritan™ copolyester for maximum

performance, safety, and clear visibility.

Blade Assembly

Stainless steel, engineered for fast and

consistent blending.

Lid

Allows ease of handling and quick removal

for high-speed operations.

Figure 3. Blender Jar Assembly

Figure 4. Sound Enclosure

Model (220/240 Volts) Amps Watts

Stealth above counter (CQB) 8 1800

Stealth in counter (IQB) 8 1800

Blendtec 220/240-volt blenders must be protected by a dedicated 10-amp circuit

breaker or fuse.

Section 3: Unpacking

3.1 Items in Package

You should have received the following items:

• Stealth blender base

• Blender jar(s) with lid(s)

• Sound enclosure

3.2 Unpacking Your Blender

• Remove the blender motor base, sound enclosure components, jar(s), and

lid(s) from the carton.

• Unwind the power cord.

• Check for and remove any packaging material blocking ventilation holes in the

blender motor base.

• Inspect all items to ensure no damage occurred during shipping.

• If any damage has occurred, immediately contact Blendtec customer service

at 1-800-BLENDTEC (US customers) or one of Blendtec’s qualiﬁed service

agents (international customers).

Note: Save all packaging for future storage or shipping.

3.2 Recording the Serial Number and Date of Shipment

Record the blender’s serial number (located on the blender base) and date of

purchase in the spaces below.

Blender Serial #: _________________________________________________________

Date of Purchase: __________________________________________________________

Refer to this information whenever contacting Blendtec or a Blendtec qualiﬁed

service agent.

Section 4: Installation

4.1 Above-Counter Installation

• Select a location for the blender that is near an electrical outlet. Also consider

proximity to ingredients, how close you want the blender to patrons, and

available counter space.

• Place the blender on the counter in a spot where the air intake vents on the

sides and exhaust on the back of the blender are unobstructed.

• Ensure there is enough room above and around the unit to allow for

unhampered movement of the sound enclosure (see Figure 5 for

measurements).

• Plug the unit into an outlet with appropriate electrical protection.

4.2 Preparation for In-Counter Installation

Note: You may locate your Blendtec Stealth in the same space as your previous

Blendtec in-counter blender. Just remember to ensure proper spacing for the sound

enclosure (see Figure 5 for measurements).

• Identify the desired blender location. Consider proximity to ingredients, how

close you want the blender to patrons, and available counter space. Also

ensure that an electrical outlet is readily accessible.

• Ensure the location meets all dimensional requirements (see Figures 5 and 6).

Figure 5. Blender Dimensions

▶The countertop can be no thicker than ¾" (19 mm). A thicker countertop

will obstruct motor ventilation.

▶If installing more than one blender, allow 14"–16" (356–506 mm) of center-

to-center blender spacing.

▶If installing a sound enclosure, allow a clearance of at least 5½" (140 mm)

from the sound enclosure to the wall and 26" (660 mm) from the countertop

to any over-the-counter cabinetry.

▶Ensure lower cabinetry allows adequate airﬂow.

• The blender draws ambient air into the vent holes located on the

upper sides of the motor and then evacuates hot air through the vents

on the bottom of the motor. For the motor to cool properly, a sufﬁcient

amount of air must be able to circulate around the motor.

• There should be at least 6½" (165 mm) of space from the countertop

to the next lower shelf of the cabinet, leaving a minimum space of

3" (76 mm) between the bottom of the motor and the lower shelf.

Cabinetry should not be closed; it should allow air to ﬂow freely from

the outside to the inside of the cabinet space. Plastic bags, cups, and

so forth, should not be stored closer than 3" (76 mm) from the bottom

of the motor.

• Cut a hole in the countertop 4³/8" (111 mm) wide and 57/8" (149 mm) long (see

the countertop hole template in the appendix). Ensure that the 4³/8" sides are

parallel with the machine operator.

Note: Double check to ensure that all space requirements and measurements are

correct before cutting.

Figure 6. In-Counter Clearance

Table des matières

Autres manuels Blendtec Mixer

Blendtec

Blendtec DESIGNER SERIES Mode d’emploi

Blendtec

Blendtec HomeBlender Mode d’emploi

Blendtec

Blendtec Total Blender Mode d’emploi

Blendtec

Blendtec Rapid Rinser Manuel utilisateur

Blendtec

Blendtec Total Blender Mode d’emploi

Blendtec

Blendtec HP3A Home Manuel utilisateur

Blendtec

Blendtec Wildside Plus Designer Series Mode d’emploi

Blendtec

Blendtec Total Blender Mode d’emploi

Blendtec

Blendtec HP3A Home Manuel utilisateur

Blendtec

Blendtec Xpress Manuel utilisateur

Blendtec

Blendtec A3-31E-BHMV Manuel utilisateur

Blendtec

Blendtec Tom Dickson Extreme Blender Manuel utilisateur

Blendtec

Blendtec Xpress Blender Manuel utilisateur

Blendtec

Blendtec TotalBlender DesignerSeries Mode d’emploi

Blendtec

Blendtec DESIGNER SERIES Mode d’emploi

Blendtec

Blendtec Total Blender Classic Combo Manuel utilisateur

Blendtec

Blendtec CLASSIC SERIES Wildside+ Mode d’emploi

Blendtec

Blendtec DESIGNER SERIES Mode d’emploi

Blendtec

Blendtec EZ 600 Mode d’emploi

Blendtec

Blendtec Signature Series Manuel utilisateur

Blendtec

Blendtec DESIGNER 625 Manuel utilisateur

Blendtec

Blendtec CLASSIC SERIES Mode d’emploi

Blendtec

Blendtec BD8 Manuel utilisateur

Blendtec

Blendtec CLASSIC SERIES Mode d’emploi

Manuels Mixer populaires d'autres marques

ROTOR

ROTOR 1125.201 Manuel utilisateur

Braun

Braun Multiquick 5 Vario series Manuel utilisateur

ARENDO

ARENDO MIRA 305424 Manuel utilisateur

CHEF-BUILT

CHEF-BUILT CCB-3500 Manuel utilisateur

Viconte

Viconte VC-4406 Manuel utilisateur

Oster

Oster BLSTAB-CB0 Manuel utilisateur

HOFFEN

HOFFEN MC-3005 Manuel utilisateur

Black & Decker

Black & Decker BLC18750DM Manuel utilisateur

Sunbeam

Sunbeam 4182 Manuel utilisateur

Bialetti

Bialetti FMX35 Manuel utilisateur

Black & Decker

Black & Decker BL8000 Manuel utilisateur

Duronic

Duronic BL530 Manuel utilisateur

Exquisit

Exquisit MS 3002 wes Manuel utilisateur

Lumme

Lumme LU-KP1891A Manuel utilisateur

Binatone

Binatone HB-735 Manuel utilisateur

Moulinex

Moulinex LM936E10 Manuel utilisateur

Oster

Oster VERSA Manuel d'installation et d'exploitation

Ninja

Ninja NN210Q Manuel utilisateur