Blendtec Rapid Rinser Manuel utilisateur

www.commercial.blendtec.com | Rapid Rinser and Rapid Rinse Station

Owner’s Manual

Forgetscrubbingjars

forgetdowntime

Just like having someone else do it for you

rapid

rinser

SECTION 1 - IMPORTANT SAFEGUARDS��4

SECTION 2 - COMPONENT OVERVIEW ��5

SECTION 3 - UNPACKING��5

SECTION 4 - INSTALLATION ��6

SECTION 5 - OPERATING INSTRUCTIONS ��6

SECTION 6 - SANITATION ��7

SECTION 7 - WARRANTY AND SERVICE ��7

SECTION 8 - RAPID RINSE STATION��9

Table of Contents

RAPID RINSER

RAPID RINSE STATION

SECTION 1 – IMPORTANT SAFEGUARDS

Read all instructions carefully before using your Rapid Rinser�

1.1 HEALTH CERTIFICATION

The Blendtec Rapid Rinser and its accessories are certiﬁed by NSF International

(NSF), under Blendtec�

1.2 WATER HOSE PRECAUTIONS

▶

Do not operate with a damaged water hose or ﬁtting�

▶

Should the water line or ﬁtting become damaged, it should be replaced by a qualiﬁed

person to avoid hazard�

▶

Do not allow the water line to hang over the edge of the work surface�

▶

Always shut the water off at the source before cleaning, moving, or servicing�

1.3 TURN OFF THE WATER WHEN NOT IN USE

1.4 NEVER OPERATE THIS DEVICE WITHOUT A BLENDER JAR (OR

OTHER DRINK CONTAINER) IN PLACE

▶

Avoid contacting the spray nozzle while the system is pressurized�

▶

Never use the unit if it is not secured to the work surface with the suction cups provided

or used in the Rapid Rinse Station�

▶

Do not rinse cracked or broken glassware with this device�

1.5 NEVER OPERATE THE UNIT IF IT APPEARS TO BE DAMAGED

If the unit malfunctions, call Blendtec ﬁrst� If it is dropped or damaged in any way, call

Blendtec Technical Support at 1�800�Blendtec (1�800�253�6383) to evaluate the extent of

damage and the possibility of either repair or replacement�

1.6 INSTALL UNIT WITH APPROPRIATE BACKFLOW PROTECTION

Backﬂow prevention must be installed to comply with federal, state or local codes that have

jurisdiction over the location�

1.7 DO NOT USE WATER THAT IS HOTTER THAN 120°F (48°C) IN THE

RAPID RINSER

SECTION 2 - COMPONENT OVERVIEW

2.1 EXTERNAL VIEW AND COMPONENTS

Refer to the lower left ﬁgure (Figure 1) below to identify the external components of the

rinser:

1� Spray nozzle

2� Rinser base

3� Water hose

4� Suction cups

5� 3/8” Compression ﬁtting (Optional 3/8” BSPT adapter)

2.2 INTERNAL COMPONENTS

Refer to the lower right ﬁgure (Figure 2) below to identify the internal components of the

rinser:

1� Magnet

2� Spring

3� Upper shell

4� Nozzle vane

5� Nozzle

6� Lower shell

7� Water valve

SECTION 3 - UNPACKING

Save your packaging materials for future storage or return shipping� Save these instructions

for future reference�

3.1 UNPACKING YOUR RAPID RINSER

You should have received the following items in your package:

1� Rapid Rinser

2� Water hose

3� Owner’s manual

4� Rapid Rinse Station - Optional see section 8

Figure 1 Figure 2

Remove all components from shipping carton and verify all items were included in the box�

Check for any packing materials that may have blocked any of the openings of the Rapid

Rinser, the water hose or compression ﬁtting� Inspect all items for possible handling damage,

immediately contact your Blendtec representative if there is evidence of broken or missing

parts�

3.2 RECORDING YOUR DATE OF PURCHASE / RECEIPT

Record below the date you received / purchased your Rapid Rinser� You will need this date

when contacting Blendtec for service�

Date of Purchase / Receipt _________________________

SECTION 4 - INSTALLATION

This equipment is to be installed with adequate backﬂow protection to comply with federal,

state, or local codes having jurisdiction�

4.1 PLACE THE RAPID RINSER IN THE SINK BASIN WHERE IT WILL BE

USED

Ensure the suction cups provided adhere to the basin ﬂoor (lightly moisten each cup with a

drop of water to facilitate suction)�

4.2 PLACE A BLENDER JAR (OR OTHER RINSABLE CONTAINER 8”

[20.3cm] WIDE OR SMALLER) OVER THE SPRAY NOZZLE

4.3 CONNECT THE WATER HOSE TO AN AVAILABLE WATER LINE

It is recommended that a certiﬁed plumber install the available water line with its own shut-

off valve�

4.4 TURN THE WATER ON

After the water line has been connected to the rinser, turn on the water supply� It is strongly

recommended that you use hot water following the requirements stated in section 1�7�

4.5 PRIME THE RINSER

Press the blender jar (or other rinsable kitchen container) down to activate the Rapid Rinser�

A steady spray of water should shoot from the nozzle into the blender jar� Release the

pressure on the blender jar to stop the ﬂow of water� Should the above not work, contact

your Blendtec representative�

SECTION 5 - OPERATING INSTRUCTIONS

5.1 PLACE THE BLENDER JAR (OR OTHER RINSABLE KITCHEN

CONTAINER) UPSIDE DOWN ON THE RAPID RINSER BASE

5.2 TURN THE WATER ON TO ACTIVATE THE RAPID RINSER

5.3 FIRMLY PRESS THE BLENDER JAR DOWN TO ACTIVATE WATER

VALVE

5.4 RELEASE THE DOWNWARD PRESSURE WHEN THE JAR HAS BEEN

RINSED TO YOUR SATISFACTION

5.5 ONCE THE SPRAY OF WATER HAS SUBSIDED, REMOVE THE

RINSED BLENDER JAR AND ALLOW IT TO DRY IN THE INVERTED

POSITION

5.6 TURN THE WATER OFF WHEN THE RAPID RINSER IS NOT IN USE.

THIS WILL PREVENT ANY POSSIBILITY OF SPRAY WHEN A BLENDER

JAR IS NOT IN POSITION

SECTION 6 - SANITATION�

6.1 SHORT-TERM SANITATION

Shut off the water� Disconnect the water hose from the water source� Carefully pull the

Rapid Rinser away from the sink basin ﬂoor� Immerse the entire Rapid Rinser in a sink full of

sanitizing solution per the sanitizer’s manufacturer’s recommendation� Pull the Rapid Rinser

out of the sanitizing solution and rinse it completely with clean water� Allow the unit to dry�

Re-attach the water ﬁtting to the water source�

6.2 LONG-TERM SANITATION

Shut off the water� Disconnect the water hose from the water source� Carefully pull the Rapid

Rinser away from the sink basin ﬂoor� Unscrew the spray nozzle from the bottom shell�

Carefully separate the two halves of the Rapid Rinser� DO NOT misplace the spring inside

the unit (see Figure 2)� Always clean and sanitize the unit as per the requirements of your

governing health department�

Thoroughly rinse the Rapid Rinser and all of its components after sanitation� Set the Rapid

Rinser and all of its components aside and allow them to dry completely� Reassemble the

Rapid Rinser by carefully placing the spring on top of the female threaded portion of the

water valve (Figure 2)� Place the top shell of the Rapid Rinser over the spring such that the

opening aligns with the spring� Insert the spray nozzle into the opening and thread until tight�

Replace the Rapid Rinser in the sink basin and reattach the water hose to the water source�

SECTION 7 - WARRANTY AND SERVICE

7.1 THE BLENDTEC RAPID RINSER IS WARRANTIED FOR A PERIOD

OF ONE YEAR FROM THE DATE OF PURCHASE / RECEIPT AGAINST

MANUFACTURING AND MATERIAL DEFECTS. THE STAINLESS STEEL

SPRAY NOZZLE HAS A LIFETIME WARRANTY

7.2 NOTE: OBVIOUS ABUSE OR MISTREATMENT OF THE RAPID RINSER

MAY VOID THE WARRANTY

7.3 SHOULD YOU NEED SERVICE, PLEASE CONTACT YOUR BLENDTEC

REPRESENTATIVE

forgetthe sink

Forget the mess

JUST let it do your dirty work

rapid

rinse

station

SECTION 8 – RAPID RINSE STATION

With the addition of the Rapid Rinse Station you will no longer need to place your Rapid

Rinser in a sink� With a water line and a drain line, you can put the Rapid Rinse Station in

the most convenient spot in the store� Most people like to put it right next to their Blendtec

blender to save time and make life smoother�

8.1 SPECIFICATIONS

DIMENSIONS: 20�2” L x 8�3” W x 6�5” H (51�3 cm x 21�1cm x16�5 cm)

WEIGHT: 5�3 lbs� (2�4 kg)

DRAIN CONNECTION: 3/4” Garden Hose Thread

8.2 DIRECTIONS

▶

Place the Rapid Rinser in the Rapid Rinse Station as shown below� If you already own the

Rapid Rinser, remove the four suction cups on the bottom before placing in the station�

▶

Connect a 3/4” garden hose drain line to the back of the rinse station and in accordance

with your local codes� We recommend using a licensed plumber for installation� Make sure

the drain line slopes away from the station since it is a gravityi-driven system�

▶

Do not allow the water line or drain line to hang over the edge of the work surface�

▶

Always shut the water off at the source before cleaning, moving, or servicing

FrontBack

8.3 CLEANING / SANITATION

▶

Using a mild soapy solution, wipe down all surfaces of the Rapid Rinse Station�

▶

Use clear, hot water to rinse the surfaces of the Rapid Rinse Station� A handheld spray

bottle will work best�

▶

To sanitize the surfaces of the Rapid Rinse Station either spray or wipe the surfaces of the

Rapid Rinse Station with the sanitizing solution diluted to the recommended level and left

on the unit per the manufacturer’s speciﬁcation�

8.4 DRYING / STORAGE

▶

The area behind the Rapid Rinse Station is designed to store and dry your jars� See

picture below for example of how this works�

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Blendtec Mixer

Blendtec

Blendtec ES3 Manuel utilisateur

Blendtec

Blendtec Stealth Manuel utilisateur

Blendtec

Blendtec BD8 Manuel utilisateur

Blendtec

Blendtec Mix n Blend II Guide rapide

Blendtec

Blendtec CLASSIC SERIES Mode d’emploi

Blendtec

Blendtec 625D Manuel utilisateur

Blendtec

Blendtec Total Blender Mode d’emploi

Blendtec

Blendtec ez Blender Manuel utilisateur

Blendtec

Blendtec Total Blender Mode d’emploi

Blendtec

Blendtec Brawn Manuel utilisateur

Blendtec

Blendtec Xpress Blender Manuel utilisateur

Blendtec

Blendtec Q-SERIES Manuel utilisateur

Blendtec

Blendtec Signature Series Manuel utilisateur

Blendtec

Blendtec HomeBlender Mode d’emploi

Blendtec

Blendtec CHEF Manuel utilisateur

Blendtec

Blendtec EZ 600 Mode d’emploi

Blendtec

Blendtec Total Blender Classic Combo Manuel utilisateur

Blendtec

Blendtec Wildside Plus Designer Series Mode d’emploi

Blendtec

Blendtec NITRO Blending Systems 2.0 Manuel utilisateur

Blendtec

Blendtec Q-SERIES Manuel utilisateur

Blendtec

Blendtec DESIGNER 625 Manuel utilisateur

Blendtec

Blendtec Total Blender Mode d’emploi

Blendtec

Blendtec CLASSIC SERIES Mode d’emploi

Blendtec

Blendtec HP3A Home Manuel utilisateur

Manuels Mixer populaires d'autres marques

ROTOR

ROTOR 1125.201 Manuel utilisateur

Braun

Braun Multiquick 5 Vario series Manuel utilisateur

ARENDO

ARENDO MIRA 305424 Manuel utilisateur

CHEF-BUILT

CHEF-BUILT CCB-3500 Manuel utilisateur

Viconte

Viconte VC-4406 Manuel utilisateur

Oster

Oster BLSTAB-CB0 Manuel utilisateur

HOFFEN

HOFFEN MC-3005 Manuel utilisateur

Black & Decker

Black & Decker BLC18750DM Manuel utilisateur

Sunbeam

Sunbeam 4182 Manuel utilisateur

Bialetti

Bialetti FMX35 Manuel utilisateur

Black & Decker

Black & Decker BL8000 Manuel utilisateur

Duronic

Duronic BL530 Manuel utilisateur

Exquisit

Exquisit MS 3002 wes Manuel utilisateur

Lumme

Lumme LU-KP1891A Manuel utilisateur

Binatone

Binatone HB-735 Manuel utilisateur

Moulinex

Moulinex LM936E10 Manuel utilisateur

Oster

Oster VERSA Manuel d'installation et d'exploitation

Ninja

Ninja NN210Q Manuel utilisateur