Black Box LE2750A Manuel utilisateur

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

LE2750A

Networking Hub

8-Port, 10BASE-T

FCC AND IC RFI STATEMENTS

FEDERAL COMMUNICATIONS COMMISSION

and INDUSTRY CANADA

RADIO FREQUENCY INTERFERENCE STATEMENTS

Class B Digital Device. This equipment has been tested and found to comply with

the limits for a Class B computing device pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. This equipment generates,

uses, and can radiate radio frequency energy, and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. If this equipment does cause harmful interference to radio or

telephone reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult an experienced radio/TV technician for help.

Caution

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate

the equipment.

To meet FCC requirements, shielded cables and power cords are required to

connect this device to a personal computer or other Class B certified device.

This digital apparatus does not exceed the Class B limits for radio noise emission from digital

apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de classe B prescrites dans le Règlement sur le brouillage

radioélectrique publié par Industrie Canada.

NETWORKING HUB

NORMAS OFICIALES MEXICANAS (NOM)

ELECTRICAL SAFETY STATEMENT

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de

que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para

referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de

operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca

de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que

sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe colocar

en libreros o gabinetes que impidan el flujo de aire por los orificios de

ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el aparato.

NOM STATEMENT

12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización

del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen del

aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas

de energia.

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

NETWORKING HUB

TRADEMARKS

UL®is a registered trademark of Underwriters Laboratories Incorporated.

Any other trademarks mentioned in this manual are acknowledged to be the property of the

trademark owners.

CONTENTS

Contents

Chapter Page

1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.1 Before You Install: Inspect the Complete Package. . . . . . . . . . . . . . . . 10

3.2 The Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.2.1 Positioning the Networking Hub on a Table or Shelf . . . . . . . . 10

3.2.2 Powering Up the Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3.2.3 Connecting Twisted-Pair Segments to the Front-Panel Ports . . 11

3.3 Cascading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.1 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4.2 Operating Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

5. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.1 Things to Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5.2 Calling Black Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

NETWORKING HUB

1. Specifications

Compliance: FCC Class B, IC Class, VDE Class B, UL®listed

Standard: IEEE 802.3 Ethernet v. 1.0/2.0

LAN Interface: RJ-45 ports for Category 3 or better twisted-pair cable

Data Rate: 10 Mbps

Partitioning: Automatic after 32 consecutive collisions

Reconnection: Occurs after 512 bits of error-free transmission

Maximum Segment Length: UTP (unshielded 10BASE-T): 100 m (328 ft.)

Indicators: (17) Front-mounted recessed LEDs: (1) Power, (8) Link/TX, and

(8) RX

Connectors: (8) Front-mounted shielded-type RJ-45 female

Leads/Signals Supported: RJ-45 Pins 1, 2, 3, and 6

Enclosure: High-strength sheet metal

Cooling Method: Convection

Temperature Tolerance: Operating: 32 to 122°F (0 to 50°C); Storage: -4 to +140°F

(-20 to +60°C)

Humidity: 10 to 95% noncondensing

Power: From wallmount power supply: Input: 120 VAC, 60 Hz; Output: 12 VDC,

1 amp; Power consumption: 6 watts typical, 10 watts maximum

Size: 0.8"H x 5"W x 4.4"D (2 x 12.7 x 11.2 cm)

Weight: Unit plus power supply: 1.3 lb. (0.6 kg)

2. Introduction

2.1 Overview

The Networking Hub installs easily for use in a home, office, or lab environment,

requiring no special rack cabinets or wiring-closet apparatus. This compact,

standard physical-layer Ethernet hub operates independently of all software.

Simple and inexpensive to use, the Hub is ideal for networking a multi-system

home or office using 10BASE-T twisted-pair cabling. The front panel has eight

shielded twisted-pair ports, and the back panel has a 120-VAC power supply outlet.

Perfect for small-to-medium-size home, office, or lab environments (two to eight

users), the Hub helps you build an independent Ethernet network. It operates as a

self-sufficient unit to provide 10BASE-T Ethernet connectivity for local users and

devices. You can easily expand small, independent networks by cascading hubs.

Expand your network for demonstrations or presentations over the network. Or

insert this handy piece of 10-Mbps Ethernet test equipment into the network to

provide a test port, and then remove it after you’re finished testing. It takes up

minimal space and uses minimal power, plus it’s rugged enough to be carried in a

coat pocket for emergencies.

Whether you place it on a table or mount it on a shelf, the hub fits easily into the

home environment. All of the wiring connectors are in the same plane so that

wiring space is neat and minimal. The external power supply conveniently plugs

into any available AC wall receptacle or power strip.

Eight RJ-45 ports support connection of up to eight workstations or other network

devices over full-length 10BASE-T cable segments. The hub fully complies with the

IEEE 802.3 specification for repeater functionality by performing signal

amplification, re-timing data packets, and re-generating preamble bits for each

packet received. Detecting collisions, extending collision fragments, and

automatically partitioning and reconnecting individual ports keep problems on

one LAN segment from causing downtime elsewhere on the network.

CHAPTER 2: Introduction

NETWORKING HUB

The front panel has Link/TX and RX LEDs for each RJ-45 port, numbered for the

corresponding ports (see Figure 2-1), and one LED for AC power. Observing the

operation and status of the ports is easy.

Figure 2-1. Front panel.

The included external wallmount power supply uses AC input power of

120 VAC/60 Hz. Its lightweight cord carries DC power to the barrel-type power

jack on the rear panel (shown in Figure 2-2).

Figure 2-2. Rear panel.

2.2 Features and Benefits

• Interoperability with other Ethernet devices: The Networking Hub is

interoperable with other Ethernet-compliant network devices. Each is fully

compliant with IEEE 802.3 specifications for 10-Mbps CSMA/CD operation.

This allows the hub to be integrated into any standard 10-Mbps Ethernet

network.

• Installation versatility: The hub’s small size makes it very unobtrusive, so it fits

easily into almost any home, office, or lab location.

• Robust network operation: The hub uses the “star” network topology and has

automatic per-port partitioning and reconnection. A fault on one segment is

isolated from the rest of the network, avoiding most network downtime.

Table des matières

Autres manuels Black Box Changer

Black Box

Black Box SW178A Manuel utilisateur

Black Box

Black Box IC454AE Manuel utilisateur

Black Box

Black Box ServSwitch SW2007A-USB Manuel utilisateur

Black Box

Black Box ServSelect IP VM KV2116A Manuel utilisateur

Black Box

Black Box ServSwitch KV0004A Manuel utilisateur

Black Box

Black Box LB9801A Manuel utilisateur

Black Box

Black Box ServSwitch Summit KV1500A Manuel utilisateur

Black Box

Black Box COS-2 Manuel utilisateur

Black Box

Black Box EMS1G24F Manuel

Black Box

Black Box LIG1014A Manuel utilisateur

Black Box

Black Box SW1020A Manuel utilisateur

Black Box

Black Box SW1042A-MM Manuel utilisateur

Black Box

Black Box LGB5028A Manuel utilisateur

Black Box

Black Box DCX3000 Manuel utilisateur

Black Box

Black Box ServSwitch KV130-UPG Manuel utilisateur

Black Box

Black Box PSE518SA Manuel utilisateur

Black Box

Black Box IC253A-US Manuel utilisateur

Black Box

Black Box LGB1152A Manuel utilisateur

Black Box

Black Box LBH21xA-H-SFP Manuel utilisateur

Black Box

Black Box SW722A-R2 Manuel utilisateur

Black Box

Black Box LGB6026A Manuel utilisateur

Black Box

Black Box ServSwitch ACXCWDM4 Manuel utilisateur

Black Box

Black Box SS2P-SH-DP-U Manuel utilisateur

Black Box

Black Box KV2004A Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur