Black Box JPM440A Manuel utilisateur

1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746

Installation

Use the splice tray with single-mode or multimode fiber cable. Follow the instructions below.

SINGLE-MODE SPLICING

1. Remove the top metal splice tray cover and install the bottom metal splice cover in the wallmount or

rackmount fiber cabinet.

2. Remove the single-mode plastic covers on each of the four single-mode plastic bases already installed in

the bottom metal splice cover.

3. Remove the yellow sticker from one of the single-mode plastic bases.

4. Install a metal sleeve and slide the single-mode fiber through it that you plan to splice. (For single-mode

fiber, you’ll use fusion splicing.)

5. Prepare and splice the fiber.

6. After splicing is complete, snap the spliced fiber in one of the 6 compartment areas in the plastic base.

7. Repeat until all 6 compartments are filled.

8. Re-install the single-mode plastic cover.

9. Repeat steps 2 through 8 for the remaining three single-mode plastic bases as required by your

application.

10. When all single-mode plastic bases are loaded with fiber, use the cable ties to secure the cable. Then

re-install the top metal splice tray cover and tighten the wing nuts (included with the cabinet).

MULTIMODE SPLICING

1. Remove the top metal splice tray cover and install the bottom metal splice cover in the wallmount or

rackmount fiber cabinet.

2. Remove the single-mode plastic covers on each of the four single-mode plastic bases already installed.

3. Remove the larger single-mode plastic bases and install the smaller multimode plastic bases in the bottom

metal splice cover. (The multimode plastic base supports the Corning Cable Systems Non-Adhesive

Mechanical Splice, Corning part number 95-000-04 or Black Box part number FO030.)

4. Splice the multimode fiber. (For multimode fiber, you’ll use mechanical splicing.)

5. After the mechanical splice is done, install the mechanical splice in one of the 6 compartments in the

multimode plastic base.

6. Repeat until all 6 compartments are filled.

7. Re-install the multimode plastic cover.

8. When all multimode plastic bases are loaded with fiber, use the cable ties to secure the cable. Then

re-install the top metal splice cover and tighten the wing nuts (included with the cabinet) to secure the

cable.

TRADEMARKS USED IN THIS MANUAL

Any trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

CUSTOMER

SUPPORT

INFORMATION

JUNE 2004

JPM440A

Splice Tray

Specifications

Size: 0.5"H x 9.4"W x 5.5"D (1.3 x 23.8 x 14 cm)

Weight: 0.8 lb. (0.4 kg)

Overview

The Splice Tray can splice up to 24 strands of single-mode or multimode fiber. It’s used with the Wallmount

Fiber Cabinets [JPM401A-R2–402A-R2] and the Rackmount Fiber Cabinets [JPM406A-R2–407A-R2 and

JPM418A-R2].

What’s Included

Your package should include the following items. If anything is missing or damaged, please contact Black Box

at 724-746-5500.

• (1) top metal splice cover

• (1) bottom metal splice cover

• (25) metal sleeves for single-mode splicing

• (4) single-mode plastic covers and bases (already installed in the bottom splice cover)

• (4) multimode plastic covers and bases

• (30) 3" (7.6-cm) cable ties

• (4) yellow stickers attached to the single-mode plastic bases

Bottom metal

splice cover

Yellow sticker

Single-mode plastic

base

Table des matières

Autres manuels Black Box Matériel réseau

Black Box

Black Box COE-8I Manuel utilisateur

Black Box

Black Box Internet Sharer FX850A Manuel utilisateur

Black Box

Black Box JPM260 Manuel utilisateur

Black Box

Black Box FT990A Manuel utilisateur

Black Box

Black Box TL601A-R2 Manuel utilisateur

Black Box

Black Box InvisaPC DTX1000-T Manuel utilisateur

Black Box

Black Box SW1009A Manuel utilisateur

Black Box

Black Box 38891 Manuel utilisateur

Black Box

Black Box TL482A-R3 Manuel utilisateur

Black Box

Black Box ServSwitch KV754A Manuel utilisateur

Black Box

Black Box LB510A Manuel utilisateur

Black Box

Black Box ServSwitch DTX5000-T Manuel utilisateur

Black Box

Black Box SW551A Manuel utilisateur

Black Box

Black Box LB0010A-A24-R2 Manuel utilisateur

Black Box

Black Box LES1208A-R2 Manuel utilisateur

Black Box

Black Box USB Director RS-232 Manuel utilisateur

Black Box

Black Box MC144A Manuel utilisateur

Black Box

Black Box AC1003A Manuel utilisateur

Black Box

Black Box JPM403A-R2 Manuel utilisateur

Black Box

Black Box 16-Port Rackmount 10/100 Manuel utilisateur

Black Box

Black Box JPM806A-HD Manuel utilisateur

Black Box

Black Box FX6412NA Manuel utilisateur

Black Box

Black Box KVT617A Manuel utilisateur

Black Box

Black Box ACU5100A Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur