Black Box JPM403A-R2 Manuel utilisateur

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 877-877-2269 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

JPM403A-R2

Fiber Wallmount Cabinet, 12-Adapter

FIBER WALLMOUNT CABINET, 12-ADAPTER

Specifications

Construction: 16-gauge steel

Size: 6.51"H x 14.02"W x 15.98"D (16.5 x 35.6 x 40.6 cm)

Weight: 20.7 lb. (9.4 kg)

What’s Included

• (1) fiber enclosure cabinet (assembled)

• (4) rectangular cable rings

• (2) sets of semi-circle cable rings (installed)

• (10) 11-inch (27.9 cm) cable ties

• (1) danger sticker

• (1) fiber ID sticker

• (2) sets of adapter label ID stickers

• (1) pair of keys “A32121"

• (1) pair of keys “B31221"

Overview

The Fiber Wallmount Cabinet, 12-Adapter mounts on a wall and holds up to 12

fiber adapters.

The cabinet enclosure has two front-access locking doors. Each door has its own

key for dual security. The left door and its corresponding key are marked with

“A32121”. Use this side of the cabinet for technician access. The right door and its

matching key are imprinted with a “B31221” marking. Use this side of the cabinet

for user access.

The cabinet enclosure has four fiber access holes, one on each corner. Inside the

enclosure, the fiber adapter panels mount vertically in the center of the cabinet.

Plus, the enclosure can support an optional splice tray.

FIBER WALLMOUNT CABINET, 12-ADAPTER

Installation

REPARINg

THE

NcLoSURE

AND

oUNTINg

ALL

1. Place the Fiber Wallmount Cabinet near the incoming fiber and patch cord

routing.

2. Mount the cabinet on a wall. Use the enclosure as a positioning template,

then use fasteners that are appropriate for the wall construction.

3. Make sure there is at least 3.2 feet (1 m) of incoming cable to terminate. You

will strip this cable to expose the fibers and then store the fiber slack in the

enclosure.

4. If splice trays are required in the cabinet, install them first. If you will not use

splice trays, use the snap-in wire clips in the mounting holes.

5. Do not exceed the minimum bend radius (for example, 1.18" [3 cm] for

900-micron buffered fiber cable) when routing the fiber slack cable.

6. Next, install the fiber adapter panel in the center vertical mount. Snap the

fiber panels into position, then press the button on the panels to lock them in

place.

NSTALLINg

THE

AbLE

1. Carefully feed approximately 54 inches (137.2 cm) of cable through the

round access port in the enclosure.

2. Mark the cable jacket where it will tie to the cable bracket.

3. Use a Kevlar®clamp (located in the upper and lower corners on the

technician’s side of the cabinet) to firmly hold the bulk fiber cable in place.

4. Carefully remove the jacket and all strength members to a point above (closer

to the end) of the tie-down point. (You will place the cable tie on jacketed

cable.) Follow the manufacturer’s recommendations for stripping and

cleaning the cable.

1000 Park Drive • Lawrence, PA 15055-1018 • 877-877-2269 • Fax 724-746-0746

TRADEMARKS USED IN THIS MANUAL

Black Box and the Double Diamond logo are registered trademarks of

BB Technologies, Inc.

Kevlar is a registered trademark of E.I. du Pont de Nemours and Company.

Any other trademarks mentioned in this manual are acknowledged to be the property of the

trademark owners.

5. Secure the cable to the cable tie bracket as shown in Figure 1.

NOTE: Do not over-tighten the cable ties!

Grid label

Cable ties

Cabinet

assembly

Place danger

label here

Cable

management

clips

Figure 1. Inside view of the cabinet.

6. Loosely route fibers around the fiber management clips to determine the best

length for terminating and storing the fiber slack. Trim the fibers, if necessary,

and remove the excess from the clips.

7. Terminate the fibers according to the connector manufacturer’s

recommendations.

NOTE: The installer must determine the proper termination method, including whether

additional supportive materials (break-out kits) are required.

8. When all fibers are terminated, clean the connectors and insert them into the

appropriate adapters.

9. Gently route the fiber slack into the management clips.

jpm403a-r2_user_rev2.pdf

Table des matières

Autres manuels Black Box Matériel réseau

Black Box

Black Box 120H Manuel utilisateur

Black Box

Black Box AC431A Manuel utilisateur

Black Box

Black Box EncrypTight Manuel utilisateur

Black Box

Black Box LrA502A-et-r5 Manuel utilisateur

Black Box

Black Box 39625 Manuel utilisateur

Black Box

Black Box IC457A-F Manuel utilisateur

Black Box

Black Box ServSwitch KV1081A Manuel utilisateur

Black Box

Black Box ACU5100A Manuel utilisateur

Black Box

Black Box Veri-NAC LVN5600A Manuel utilisateur

Black Box

Black Box USB Director RS-232 Manuel utilisateur

Black Box

Black Box TL553A-R3 Manuel utilisateur

Black Box

Black Box MT330A Manuel utilisateur

Black Box

Black Box LD485A-MP Manuel utilisateur

Black Box

Black Box LES1208A-R2 Manuel utilisateur

Black Box

Black Box Lineshare Master - 4 Manuel utilisateur

Black Box

Black Box RF200A Manuel utilisateur

Black Box

Black Box ServSelect KV119A Instructions d'installation et d'entretien

Black Box

Black Box SW1009A Manuel utilisateur

Black Box

Black Box CMA005A Manuel utilisateur

Black Box

Black Box MT1500A Manuel utilisateur

Black Box

Black Box LWS100AE Manuel utilisateur

Black Box

Black Box DTX5000-CTL-R2 Manuel utilisateur

Black Box

Black Box LT2060A Manuel utilisateur

Black Box

Black Box EME149A-20 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur