Biostar P4VTC Manuel utilisateur

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. There is no guarantee that interference will not occur in

a particular installation.

The vendor makes no representations or warranties with respect to the

contents here of and specially disclaims any implied warranties of

merchantability or fitness for any purpose. Further the vendor reserves

the right to revise this publication and to make changes to the contents

here of without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without

first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice

and we will not be responsible for any mistakes found in this user’s

manual. All the brand and product names are trademarks of their

respective companies.

LAYOUT OF P4VTC ................................................................................1

COMPONENT INDEX.............................................................................2

ENGLISH...................................................................................................3

P4VTC Features......................................................................................................... 3

Package contents......................................................................................................4

How to setup Jumper ................................................................................................ 5

CPU Installation ......................................................................................................... 5

DDR DIMM Modules: DIMM1/ DIMM2........................................................................ 6

Jumpers, Headers, Connectors & Slots................................................................... 7

WARPSPEEDER.....................................................................................14

Introduction.............................................................................................................. 14

System Requirement............................................................................................... 14

Installation................................................................................................................ 15

Usage........................................................................................................................ 16

STUDIOFUN!TM (OPTIONAL) .............................................................24

Introduction.............................................................................................................. 24

Hardware Requirements.......................................................................................... 24

Installation and Usage............................................................................................. 24

TROUBLE SHOOTING.........................................................................25

Layout of P4VTC

※NOTE: ●represents the first pin.

JKBMS1

Mouse &

Keyboard

JUSB1

JATXPWR2

JKBV1

JAUDIO1

USB

JUSBV1

Parallel Port

JCOM1

COM1COM2

JPRNT1

JATXPWR1

JCOM2

JUSBLAN1

JAUDIO

JUSBV2

Socket 478

CPU1

PT800

AGP SLOT

PCI1

PCI SLOT

PCI2

PCI SLOT

PCI3

JCDIN1

JCDIN2

CODEC

JSPDIF1

ITE I/O

BIOS

CNR SLOT

CNR1

JWOL1

JSFAN1

FLOPPY DISK CONN.

FDD1

216 115

JGAME1

JC1

JPANEL1

JCMOS1

JSATA1

JSATA2

JUSB4

1021

JUSBV3

JUSB3

BAT1

PRIMARY IDE CONN.

SECONDARY IDE CONN.

DIMM2

DIMM1

JCFAN1

Component Index

A. Power Source Selection for Keyboard N. Wake On LAN Header (JWOL1)

and Mouse (JKBV1) O. System FAN Header (JSFAN1)

B. Power Source Selection for USB P. Floppy Disk Connector (FDD1)

(JUSBV1) Q. Game Port Header (JGAME1)

C. Back Panel Connector R. Front Panel Connector (JPANEL1)

D. ATX Power Connector (JATXPWR2) S. Case Open Connector (JC1)

E. ATX Power Connector (JATXPWR1) T. Serial ATA Connector (JSATA1-2)

F. Power Source Selection for USB U. Clear CMOS (JCMOS1)

(JUSBV2) V. Front USB Header (JUSB4)

G. Front Audio Header (JAUDIO1) W. Front USB Header (JUSB3)

H. Accelerated Graphic Port Slot (AGP1) X. Power Source Selection for USB

I. CD-ROM Audio-In Header (JCDIN2) (JUSBV3)

J. CD-ROM Audio-In Header (JCDIN1) Y. IDE Connectors (IDE1-2)

K. PCI BUS Slots (PCI 1-3) Z. DIMM Modules (DIMM1-2)

L. Digital Audio Connector (JSPDIF1) A1 CPU Fan Connector (JCFAN1)

M. Communication Network Riser Slot

(CNR1)

Socket 478

PT800

CODEC

ITE I/O

BIOS

BAT1

IJ K

MNO

English

P4VTC Features

A. Hardware

CPU

Provides Socket 478.

Supports the Intel® processor.

Supports Hyper-Threading Technology.

Front Side Bus at 400/533/800 MHz.

Chipset

North Bridge: VIA PT800.

South Bridge: VIA VT8237.

Main Memory

Supports up to 2 DDR devices.

Supports 200/266/333/400 MHz DDR devices.

Maximum memory size of 2GB.

Super I/O

Chip: ITE IT8705.

Slots

Three 32-bit PCI bus master slots.

One AGP slot.

One CNR slot.

On Board IDE

Supports four IDE disk drives.

Supports PIO Mode 4, Bride Mode and Ultra DMA 33/66/100/133 Bus Master

Mode.

LAN

Chip: VIA VT6103.

Supports 10 Mb/s and 100 Mb/s auto-negotiation

Half/ Full duplex capability.

On Board AC’97 Sound Codec

Chip: CMI9739A.

Compliant with AC’97 specification.

AC99 2.2 interface.

Supports 6 channels.

On Board Peripherals

a. Rear side

2 serial ports.

1 parallel port. (SPP/EPP/ECP mode)

Audio ports in vertical position.

1 LAN jack.

PS/2 mouse and PS/2 keyboard.

4 USB2.0 ports.

b. Front Side

1 floppy port supports 2 FDDs with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes.

4 USB2.0 ports

1 front audio header.

Dimensions

ATX Form Factor: 24.5 X 22.5cm (W X L)

B. BIOS & Software

BIOS

Award legal Bios.

APM1.2.

ACPI.

USB Function.

Software

Supports WarpspeederTM, 9th TouchTM, FLASHER™, WinFlasherTMand StudioFun!

(optional).

Offers the highest performance for Windows 98 SE, Windows 2000, Windows Me,

Windows XP, SCO UNIX etc.

Package contents

HDD Cable X1

FDD Cable X1

User’s Manual X1

USB Cable X1 (optional)

Rear I/O Panel for Micro ATX Case X1 (optional)

Fully Setup Driver CD X1

StudioFun! Application CD X1 (optional)

S/PDIF Cable X 1(optional)

How to setup Jumper

The illustration shows how jumpers are setup.When the Jumper cap is placed on pins, the

jumper is “close”. If no jumper cap is placed on the pins, the jumper is ”open”. The

illustration shows a 3-pin jumper whose pin 1and 2 are “close” when jumper cap is placed

on these 2 pins.

Jumper close Jumper open Pin 1-2 close

CPU Installation

Step1: Pull the lever sideways away from the socket and then raise the lever up to a

90-degree angle.

Step2: Look for the white dot/cut edge. The white dot/cut edge should point towards the

lever pivot. The CPU will fit only in the correct orientation.

Step3: Hold the CPU down firmly, and then close the lever.

Step4: Put the CPU fan on the CPU and buckle it. Connect the CPU fan power cable to

the JCFAN1. This completes the installation.

Step1 Step2 Step3 Step4

CPU Fan Header: JCFAN1

Pin No. Assignment

1 Ground

2 +12V

JCFAN1 3 FAN rpm rate Sense

System Fan Header: JSFAN1

Pin No. Assignment

1 Ground

2 +12V

JSFAN1

3 FAN rpm rate Sense

DDR DIMM Modules: DIMM1/ DIMM2

DRAM Access Time: 2.5VUnbuffered DDR 200/266/333/400 MHz Type required.

DRAM Type: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184 pin)

Total Memory Size with Unbuffered DIMMs

DIMM Socket

Location DDR Module Total Memory

Size (MB)

DIMMB1 64MB/128MB/256MB/512MB/1GB

DIMMB2 64MB/128MB/256MB/512MB/1GB

Max is

2 GB

***Only for reference***

Installing DDR Module

1. Unlock a DIMM slot by pressing the retaining

clips outward. Align a DIMM on the slot such

that the notch on the DIMM matches the

break on the slot.

2. Insert the DIMM firmly and vertically into the

slot until the retaining chip snap back in

place and the Dimm is properly seated.

Jumpers, Headers, Connectors & Slots

Floppy Disk Connector: FDD1

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the

provided floppy drive ribbon cables.

Hard Disk Connectors: IDE1/ IDE2

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/ 66/ 100/ 133 functionality. It has two

HDD connectors IDE1 (primary) and IDE2 (secondary).

The IDE connectors can connect a master and a slave drive, so you can connect

up to four hard disk drives. The first hard drive should always be connected to

IDE1.

Peripheral Component Interconnect Slots: PCI 1-3

This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral

Component Interconnect, and it is a bus standard for expansion cards. This PCI

slot is designated as 32 bits.

Accelerated Graphics Port Slot: AGP1

Your monitor will attach directly to that video card. This motherboard supports

video cards for PCI slots, but it is also equipped with an Accelerated Graphics Port

(AGP). An AGP card will take advantage of AGP technology for improved video

efficiency and performance, especially with 3D graphics.

Communication Network Riser Slot: CNR1

The CNR specification is an open Industry Standard Architecture, and it defines a

hardware scalable riser card interface, which supports modem only.

Serial ATA Connector: JSATA1/ JSATA2

The motherboard has a PCI to SATA Controller with 2 channels SATA interface, it

satisfies the SATA 1.0 spec and with transfer rate at 1.5Gb/s.

Front Panel Connector: JPANEL1

Front USB Header: JUSB3/ JUSB4

Pin Assignment Pin Assignment

1 +5V(fused) 2 +5V(fused)

3 USBP4- 4 USBP5-

5 USBP4+ 6 USBP5+

7 Ground 8 Ground

JUSB3/4 9 KEY 10 NA

Wake On LAN Header: JWOL1

Pin Assignment

1 +5V Standby

2 Ground

JWOL1

3 Wake up

SPK

PWR_LED

HLED

SLP

RST

224

123

IRON/OFF

(+) (-)

(+) (-)(+)

Pin Assignment Function Pin Assignment Function

1 +5V 2 Sleep Control

3 NA 4 Ground Sleep

Button

5 NA 6 NA NA

7 Speaker

Speaker

Connector

8 Power LED (+)

9 HDD LED (+) 10 Power LED (+)

11 HDD LED (-) Hard Drive

LED 12 Power LED (-)

POWER

LED

13 Ground 14 Power Button

15 Reset Control Reset

Button 16 Ground Power-on

Button

17 NA

18 KEY

19 NA 20 KEY

21 +5V 22 Ground

23 IRTX

IrDA

Connector

24 IRRX

IrDA

Connector

JPANEL1

Table des matières

Autres manuels Biostar Carte mère

Biostar

Biostar B350GT3 Manuel utilisateur

Biostar

Biostar G965 MICRO 775 Guide de l'utilisateur

Biostar

Biostar Z490GTA EVO Manuel utilisateur

Biostar

Biostar MCP6PB M2+ Guide de l'utilisateur

Biostar

Biostar GF8200 M2 PLUS - BIOS Guide de l'utilisateur

Biostar

Biostar M6VCF Manuel utilisateur

Biostar

Biostar PT880 Pro-A7 Combo Manuel utilisateur

Biostar

Biostar TA75M Guide de l'utilisateur

Biostar

Biostar M7VKF Manuel utilisateur

Biostar

Biostar M6VLQ Grand Manuel utilisateur

Biostar

Biostar M7 VKS Manuel utilisateur

Biostar

Biostar B660GTQ Manuel utilisateur

Biostar

Biostar P4 TSE Pro Manuel utilisateur

Biostar

Biostar I865G-M7 Manuel utilisateur

Biostar

Biostar P4TGE Manuel utilisateur

Biostar

Biostar H170GTN Manuel utilisateur

Biostar

Biostar Hi-Fi A70U3P Guide de l'utilisateur

Biostar

Biostar I945G-M7 Manuel utilisateur

Biostar

Biostar G41D3B Guide de l'utilisateur

Biostar

Biostar TP43D2-A7 Manuel

Biostar

Biostar TP55 - BIOS Manuel utilisateur

Biostar

Biostar Hi-Fi A85S3 PLUS Manuel utilisateur

Biostar

Biostar TP43 HP - BIOS Manuel utilisateur

Biostar

Biostar I86PE-A4 Guide de l'utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur