Biostar M7 VIQ Manuel utilisateur

FCC Statement and Copyright

This equipment has been tested and found to comply with the limits of a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. There is no guarantee that interference will not occur in a

particular installation.

The vendor makes no representations or warranties with respect to the

contents here of and specially disclaims any implied warranties of

merchantability or fitness for any purpose. Further the vendor reserves the

right to revise this publication and to make changes to the contents here of

without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole is not allowed without

first obtaining the vendor’s approval in writing.

The content of this user’s is subject to be changed without notice and we

will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

ENGLISH..................................................................................................... 1

M7VIQ Features .................................................................................................................1

Package contents..............................................................................................................1

Layout of M7VIQ ................................................................................................................2

CPU Installation.................................................................................................................3

DDR DIMM Modules: DDR1-2 ...........................................................................................4

Jumpers, Headers, Connectors & Slots..........................................................................5

ESPAÑOL ................................................................................................. 12

Características del M7VIQ ..............................................................................................12

Contenido del Paquete.................................................................................................... 12

Disposición del M7VIQ.................................................................................................... 13

Instalación del CPU.........................................................................................................14

Módulos DDR DIMM: DDR1-2.........................................................................................15

Conectores, Cabezales, Puentes y Ranuras.................................................................16

TROUBLE SHOOTING............................................................................. 23

SOLUCIÓN DE PROBLEMAS ................................................................. 24

iip

iio

English

M7VIQ Features

 Use Via KM266/ VT8235 Chipset, W83697HF, LAN Chip (optional).

 Contains on board I/O facilities, which include one serial port, one VGA port,

a parallel port, a PS/2 mouse port, a PS/2 keyboard port, audio ports, USB

ports, a LAN port (optional) and a game port.

 Supports the single AMD Socket A for Athlon™(Thunderbird™) / Athlon

XP™/ Duron ™processors running at 200/266 MHz Front Side Bus (FSB).

 Supports Ultra 133/100/66/33, PIO modes, Ide hard disk drives, LBA mode.

 Supports 2 DDR 200/266 MHz (without ECC) devices

 Supports one CNR Slot (Type B only), three 32-bit PCI Bus slots, and one

AGP Slot.

 Complies with PC Micro-ATX form factor specifications.

 Supports popular operating systems such as Windows NT, Windows 2000,

Windows ME, Windows XP, LINUX and SCO UNIX.

 Via®AC’97 2.2 compatible.

 High S/N ratio meets PC 99 requirements.

 4CH DAC, applicable for leading motherboard chipsets.

 Line-in phonejack share with rear out.

Package contents

 HDD Cable X 1, FDD Cable X 1, Fully Setup Driver CD X 1

 Flash Memory Writer for BIOS update X 1

 USB Cable X 2 (Optional)

 Rear I/O Panel for ATX Case X 1 (Optional)

iip

iio

Layout of M7VIQ

JPRNT1

JCOM1

JVGA1

JKBMS1

JUSBLAN1

JAUD GAME

JSPKR1

SP-OUT

JMIC1

MIC-IN

JLIN1

LINE-IN

GAME Port

T8375

(

KM 266

)

JCFAN1

FDD1

FLOPPY DISK CONN.

PRIMARY IDE CONN.

JDIMMVOLT

JATXPWER1

Winbond

W83697HF

JSFAN1

JPANEL1 12

IDE1 IDE2

JCMOS1

BAT1

T 8235

SECONDARY IDE CONN.

DDR2

DDR1

JUSBV1

JKBV1

PCI3

PCI2

PCI1

JUSB2

JWOL1

JCODECSEL

Codec

LAN CHIP

JUSB3

JUSBV2

JUSBV3

JDJ1 5

iip

iio

CPU Installation

1. Pull the lever sideways away from the socket then raise the lever up

to 90-degree angle.

2. Locate Pin A in the socket and lock for the white dot or cut edge in

the CPU. Match Pin A with the white dot/cut edge then insert the

CPU.

3. Press the lever down. Then Put the fan on the CPU and buckle it

and put the fan’s power port into the JCFAN1, then to complete the

installation.

CPU/ System Fan Headers: JCFAN1/ JSFAN1

CPU

JSFAN1 JCFAN1

Ground

12V

Sense

Ground

12V

Sense

iip

iio

DDR DIMM Modules: DDR1-2

DRAM Access Time: 2.5V Unbuffered DDR 200/266 MHz Type

required.

DRAM Type: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184

pin)

DIMM Socket

Location DDR Module Total Memory

Size (MB)

DDR 1 64MB/128MB/256MB/512MB/1GB

DDR 2 64MB/128MB/256MB/512MB/1GB

Max is

2GB

* The list shown above for DRAM configuration is only for reference.

How to install a DIMM Module

1. The DIMM socket has a

“ Plastic Safety Tab”, and the

DIMM memory module has an

“Asymmetrical notch”, so the

DIMM memory module can only

fit into the slot in one direction.

2. Push the tabs out. Insert the

DIMM memory modules into the

socket at a 90-degree angle, then

push down vertically so that it will

fit into the place.

3. The Mounting Holes and plastic

tabs should fit over the edge and

hold the DIMM memory modules

in place.

iip

iio

Jumpers, Headers, Connectors & Slots

Hard Disk Connectors: IDE1/ IDE2

The motherboard has a 32-bit Enhanced PCI IDE Controller that

provides PIO Mode 0~4, Bus Master, and Ultra DMA / 33/ 66/ 100/ 133

functionality. It has two HDD connectors IDE1 (primary) and IDE2

(secondary).

The IDE connectors can connect a master and a slave drive, so you can

connect up to four hard disk drives. The first hard drive should always be

connected to IDE1.

Floppy Disk Connector: FDD1

The motherboard provides a standard floppy disk connector that

supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This

connector supports the provided floppy drive ribbon cables.

Communication Network Riser Slot: CNR1

The CNR specification is an open Industry Standard Architecture, and it

defines a hardware scalable riser card interface, which supports

modem only.

Peripheral Component Interconnect Slots: PCI1-3

This motherboard is equipped with 3 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for

expansion cards. This PCI slot is designated as 32 bits.

Accelerated Graphics Port Slot: AGP1

Unlike the mouse ports, keyboard ports and printer ports, this

motherboard does not have built in video facilities; and therefore,

requires a video card for one of the expansion slots. Your monitor will

attach directly to that video card. Tis motherboard supports video cards

for PCI, but is also equipped with an Accelerated Graphics Port (AGP).

An AGP card will take advantage of AGP technology for improved video

efficiency and performance, especially with 3D graphics.

iip

iio

Power Connectors: JATXPWR1

DIMM Power Selection Connector: JDIMMVOLT

 It strongly recommended to set DDR DIMM voltage in default setting

2.5V, and it for over voltage function.

Wake On LAN Header: WOL1

Clear CMOS Jumper:

JCMOS

WOL1

5V_SB Wake up

Ground

JATXPWR1

(ATX Main Power Conn.)

JATXPWR1

(ATX Main Power Conn.)

JDIMMVOLT

Pin 1-2 on ==> 2.5V

Pin 3-4 on ==> 2.6V

Pin 5-6 on ==> 2.7V

Pin 7-8 on ==> 2.8V

(Default ==> 2.5V)

JCMOS1

Clear CMOS

Data

Pin 1-2 on

Normal

Operation

(default)

Assignment

Pin 2-3 on

iip

iio

Front USB Header: JUSB2/ JUSB3

5V/ 5VSB Selection for USB: JUSBV1/2/3

CPU Frequency Selection: JCLK1

JCLK1

On ==> 100MHz

Off ==> 133MHz

JUSB1/2

Pin Assignment Pin Assignment

910

+5V +5V

Data (-)Data (-)

Data (+) Data (+)

Ground Ground

Key NA

JUSBV1/2/3

5V_SB

Pin 1-2 on

Assignment

Pin 2-3 on

iip

iio

5V/ 5VSB Selection for Keyboard: JKBV1

CNR Codec Primary/ Secondary Selection:

JCODECSEL

JKBV1

5V_SB

Pin 1-2 on

Assignment

Pin 2-3 on

Pin 1-2 On-board Primary

Codec (Default).

1Pin 2-3 CNR Primary Codec.

Assignment

J_CODECSEL

Autres manuels pour M7 VIQ

Table des matières

Langues :

Autres manuels Biostar Carte mère

Biostar

Biostar H110M-BTC Manuel utilisateur

Biostar

Biostar 945GC-230 - BIOS Manuel utilisateur

Biostar

Biostar M7VIZ V8.X Manuel utilisateur

Biostar

Biostar TA760G M2+ Guide de l'utilisateur

Biostar

Biostar M7VIG Pro D Manuel utilisateur

Biostar

Biostar Hi-Fi A68U3P Guide de l'utilisateur

Biostar

Biostar A770E - BIOS Manuel utilisateur

Biostar

Biostar TA785G3 PLUS - BIOS Guide de l'utilisateur

Biostar

Biostar NF325-A7 Guide de l'utilisateur

Biostar

Biostar M7VIG Pro D Manuel utilisateur

Biostar

Biostar M7 VKS Manuel utilisateur

Biostar

Biostar M7 VKH Manuel utilisateur

Biostar

Biostar TP45E Combo Guide de l'utilisateur

Biostar

Biostar B550GTA Manuel utilisateur

Biostar

Biostar P4 SFA Instructions d'utilisation et d'installation

Biostar

Biostar H610MX-E Manuel utilisateur

Biostar

Biostar A960D+V2 Guide de l'utilisateur

Biostar

Biostar NF61S MICRO AM2 SE Guide de l'utilisateur

Biostar

Biostar P4 TDQ Guide de l'utilisateur

Biostar

Biostar BIH11-AHA Manuel utilisateur

Biostar

Biostar M7VIW-D Guide de l'utilisateur

Biostar

Biostar TA770 A2 Guide de l'utilisateur

Biostar

Biostar M7TDR Manuel utilisateur

Biostar

Biostar M6VSB Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuel utilisateur