BETAFPV LiteRadio 1 Manuel utilisateur
LiteRadio 1 Radio Transmitter
01
The LiteRadio 1is a compactradio transmitter for theFPVent market. This radio
transmitteris poable, appealing and practical. It is a remote control suitable for
FPVent-level users.
As a new member of LiteRadio series, LiteRadio 1has the following characteristics.
● 8 channels in total.
● Suppo CC2500 version built-in protocol switching.
● Congure 1000mAh batte and USB charge suppoted.
● Suppo BETAFPV Congurator for updating, conguring and tuning.
● USB joystick suppo for most practice simulators.
1. Oveiew
Front view
Switch B Switch C
Switch DSwitch A
LED light
Direction JoystickThrottle Joystick
The LiteRadio 1 is compatible with two types of joystick heads. When replacing the
joystick head, please be aware not to twist the joystick head. Instead, pull it out
directly, then replace the joystick head. As shown below:
Bottom view
The radio transmitterhas two joysticks whichfunctions are as following:
● Throttle joystick: Push the stick up and down to control the throttle value of the
drone; push the stick left and right to control the steering angle value of the drone;
● Direction joystick: Push the stick up and down to control the forward and
2. Joystick & Button Introduction
02
Power Button Type-C Po
SETUPBIND Batte
Compament
Please plug & remove
the joystick head veically
Note：
Do not twist the
joystick head
backward movement of the drone; push the stick left and right to control the left
and right movement of the drone;
There are 7 buttons or switches on the remote control, and their functions are as
following:
● Channel keys: SA\SB\SC\SD keys correspond to four channel switches, and each
channel can be set to two levels of gears.
● Power Button: Switch the power button to the right to turn on, and switch the
power button to the left to turn o.
● BIND Button: Enter binding mode after radio transmitter is powered on.
● SETUP Button: Enter joystick calibration mode after radio transmitter is powered
on.
Note: This chapter only applies to the CC2500 version of the radio transmitter.
4. Switching Protocol
3. LED Indicator and Buzzer
● The LED light indicates the working status of the radio transmitter.
The radio transmitter has a built-in buzzer. When it alarm twice as "di - di", it means
that the batte is too low and the radio transmitter needs to be charged.
Reason Solution
Blue light solid on Working
Lower throttle and switches to
the lowest position.
Turn to blue then.
Red light solid on
Red light ashing quickly
Blue light ashing slowly
Red light breathes slowly
The throttle joystick or
switches are not in the lowest
The radio transmitter is binding
Batte reaches the low
voltage limit
On charging
Green light breathes slowly Charge complete
Charge the transmitter
Wait for completing binding
State of the LED Light
03
Note: LiteRadio 1 only work with D16 ACCST 1.x Frsky protocol. So if you use a Frsky receiver
with D16 ACCST 2.X version or ACCESS version, binding will fail.
How to check the current protocol
The CC2500 version radio transmitter could suppo 4 dierent protocols, including
Frsky D16 FCC, Frsky D16 LBT, Frsky D8 and Futaba S-FHSS. The current protocol
is indicated by the ashing times of the red LED when power on, before the buzzer
alarm.
How to change the current protocol
Below are the steps to change protocol (Frsky FCC D16, Frsky D16 LBT, Frsky D8,
or Futaba S-FHSS),
1. Power o the radio transmitter;
2. Press and hold the BIND button while power on the radio transmitter;
3. Then the ash times of the red LED before buzzer alarms will change, according
to the tables above.
04
5. Binding the Receiver
There are the steps to make the LiteRadio 1 enter binding status.
1. Power on the remote control radio transmitterand wait for its system to load
completely. LED light is solid blue.
2. Enter receiver's binding mode, and wait for it to bind with the radio;
3. Press the bind button on the bottom of the transmitter to enter binding status.
The LED light will be red and ash quickly.
4. The LED light will change to solid blue 5 seconds later when transmitter exits
binding status. If not bind successfully, repeat theprocessabove.
LED Status Protocol Version
Flash once Frsky D16 FCC（ACCST 1.X 版本）
Flash twice Frsky D16 LBT（ACCST 1.X 版本）
Flash Three Times Frsky D8
Flash Four Times Futaba S-FHSS
The continue working time for full charged batte is about 8 hours.
Fast charging protocol is not suppoed. So radio transmitter can not be quickly charged.
05
It is the safest and quickest method to get staed by using FPV simulator for
staers. LiteRadio 1 remote control radio transmitter suppos most of FPV
simulators on market with comprehensive conguration.
6. Charging
7. HID Joystick
Remote control radio transmitter has a built-in 1000mAh batte. When the red
light ashes twice and the buzzer alarms twice, indicates that radio transmitter is
low batte and needs to be re-charged. Below are the charging methods for
reference:
● Turn o the radio transmitter.
● Plug in remote control radio transmitter with adapter by USB cable (5V output
adapter is allowed).
● The LED light breathes in red means charging, while in green means fully charged.
Output 5V
Type-C Data Cable
06
8. Joystick Calibration
Operation steps below:
● Turn o radio transmitter.
● Connect the transmitter to computer via USB data cable. Wait for the LED light
breathes in red or green.
● Install driver from PC automatically, prompt box pops up after successful
installation. Then, remote control radio transmitter works normally.
User needs to manually install driver if PC doesn't install automatically or installed
incorrectly.
The joystick data may oset after it has used for a period of time (if joysticks is hit
by physical). User need to re-calibrate joysticks based on following steps;
DO NOT power on the transmitter rst and connect it to the PC. The USB po is invalid in this
situation.
BETAFPV Joystick
Other devices
Type-C Data Cable
FPV Simulator
Setting up a device
We’re setting up ‘ BETAFPV JoyStick’.
07
● After powering on, press SETUP button on the back of remote control radio
transmitter, it hears two "Bee Bee" sounds, and red LED ash quickly (two ashes
each time), which means remote control radio transmitter entered calibration
mode.
● Move throttle joystick and direction joystick to middle position, press SETUP
button again, wait until the buzzer beep three "Bee Bee Bee" sounds, red LED light
ashes quickly (two ashes each time), which indicates joystick data has been
acquired and enter into the bounda value calibration mode.
● Toggle the joystick to move to the top, bottom, left, and right joystick boundaries
respectively (do not to press too hard, the joystick just needs to touch the
bounda) and keep the position for 1-2S, then press the SETUP button one more
time, we can hear a long beeping sound (about 3 seconds) from the buzzer again,
and the red LED light stops ashing, indicating that the calibration of the joystick
is completed.
9. BETAFPV Congurator
BETAFPV Congurator is utility designed to simplify updating, conguring and
tuning the radio transmitter.
Download address: https://github.com/BETAFPV/BETAFPV_Congurator/releases
How to enter the radio transmitter conguration page:
● Turn o the radio transmitter.
● Connect the transmitter to computer via USB data cable. Wait for the LED light
breathes in red or green.
● Open the BETAFPV Congurator program in your computer and switch to the
congurator page for radio transmitter.
● Click the "Connect Radio Controller" button on the top right of the page.
Available conguring seices include:
● Change joystick mode (Left / Right stick throttle )．
● Mixing, trimming of each channel and other switching．
DO NOT power on the transmitter rst and connect it to the PC. The USB po is invalid in this
situation.
08
LiteRadio 1 遥控器是针对入门市场的一款小巧型遥控器。这款遥控器集实用、美观、便
携于一体，是一款适合入门级用户的遥控器。
LiteRadio 1 作为LiteRadio系列中新的成员，它具备了以下特点。
● 支持8通道
● 支持CC2500版本内置协议切换
● 配置1000mAh电池，支持USB充电
● 支持BETAFPV Congurator上位机调参和升级
● USB Joystick模式支持绝大部分模型模拟器
LiteRadio 1 遥控器正面如下图所示。
1.外观形态
二段开关
指示灯
方向摇杆油门摇杆
二段开关
二段开关
二段开关
09
LiteRadio 1 遥控器可以适配两款摇杆头，当切换摇杆头时需要注意，不可旋拧摇杆头，
而是应该直接拔取下来，再更换摇杆头。如下图所示：
LiteRadio 1 遥控器底面如下图所示。
电源键 Type-C接口
SETUPBIND 电池仓
垂直上下插拔安装
注意：
切勿旋转摇杆
Table des matières
Manuels Émetteur populaires d'autres marques
Dejero
Dejero EnGo 3x Manuel utilisateur
Rosemount
Rosemount 4600 Manuel utilisateur
Speaka Professional
Speaka Professional 2342740 Manuel utilisateur
trubomat
trubomat GAB 1000 Manuel utilisateur
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Manuel utilisateur
Rondish
Rondish UT-11 Manuel utilisateur
