Bend-Pak XPR-10 Series Manuel utilisateur

1645 Lemonwood Dr.

Santa Paula, CA 93060 USA

Toll Free: (800) 253-2363

Tel: (805) 933-9970

bendpak.com

XPR-10 Series Two-Post Lifts

Installation and Operation Manual

Manual P/N 5900951 — Manual Revision D — May 2019

Models:

•XPR-10S

•XPR-10AS

•XPR-10XLS

•XPR-10AXLS

Model XPR-10S shown.

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠DANGER

Read the

entire

contents of this manual

before

using this

product. Failure to follow the instructions and safety precautions in

this manual can result in serious injury or death. Make sure all other

operators also read this manual. Keep the manual near the product

for future reference. By proceeding with setup and operation, you

agree that you fully understand the contents of this manual.

Manual. XPR-10 Series Two-Post Lifts, Installation and Operation Manual, Manual Part Number 5900951,

Manual Revision D, Released May 2019.

agree that: full attribution goes to BendPak Inc., you are not authorized to make changes to the content, you do

not gain any rights to this content, and you will not use the copies for commercial purposes.

Trademarks. BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company,

product, and service names are used for identification only. All trademarks and registered trademarks mentioned

in this manual are the property of their respective owners.

Limitations. Every effort has been made to ensure complete and accurate instructions are included in this

manual. However, product updates, revisions, and/or changes may have occurred since this manual was

published. BendPak reserves the right to change any information in this manual without incurring any obligation for

equipment previously or subsequently sold. BendPak is not responsible for typographical errors in this manual.

You can always find the latest version of the manual for your product on the BendPak website.

Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment to the value of

your new product. Contact your nearest BendPak dealer or visit www.bendpak.com/support/warranty for

full warranty details. Go to bendpak.com/support/register-your-product/ and fill out the online form to

Safety.Your Lift was designed and manufactured with safety in mind. Your safety also depends on proper

training and thoughtful operation. Do not set up, operate, maintain, or repair the Lift without reading and

understanding this manual and the labels on the unit;

do not use your Lift unless you can do so safely!

Owner Responsibility. In order to maintain your product properly and to ensure operator safety, it is the

responsibility of the product owner to read and follow these instructions:

• Follow all installation, operation, and maintenance instructions.

• Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations,

such as state and federal OSHA regulations and electrical codes.

• Read and follow all safety instructions. Keep them readily available for operators.

• Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.

• Do not operate the product until you are certain all parts are in place and operating correctly.

• Carefully inspect the product on a regular basis and perform all maintenance as required.

• Service and maintain the unit only with approved replacement parts.

• Keep the manual with the product and make sure all labels are clean and visible.

•Only use the Lift if it can be used safely!

Unit Information.

Enter the Model Number, Serial

Number

, and the Date of Manufacture from the ID label

on your unit

. This information is required for part or

warranty issues.

Model:

Serial:

Date of Manufacture

XPR-10 Series Two-Post Lifts 3P/N 5900951 — Rev. D — May 2019

Table of Contents

Introduction 3 Operation 66

Shipping Information 3 Maintenance 72

Safety Considerations 4 Troubleshooting 74

FAQ 6 Wiring Diagrams 76

Components 7 Labels 77

Specifications 9 Parts Drawings 80

Installation Checklist 14 ALI Store 90

Installation 15 Maintenance Log 91

Introduction

This manual describes these XPR-10 Series Two-Post Lift models:

•XPR-10S. A Two-Post Symmetric Lift that raises Vehicles up to 10,000 pounds (4,536 kg).

Also available with extended height (for taller Vehicles), Low-Pro™ arms, and both.

•XPR-10AS. A Two-Post Asymmetric Lift that raises Vehicles up to 10,000 pounds (4,536 kg).

Also available with extended height (for taller Vehicles), Low-Pro™ arms, and both.

•XPR-10XLS. A Two-Post Symmetric Lift with extended rise under the Vehicle (for taller

mechanics) that raises Vehicles up to 10,000 pounds (4,536 kg).

Also available with extended height (for taller Vehicles), Low-Pro™ arms, and both.

•XPR-10AXLS. A Two-Post Asymmetric Lift with extended rise under the Vehicle (for taller

mechanics) that raises Vehicles up to 10,000 pounds (4,536 kg).

Also available with extended height (for taller Vehicles), Low-Pro™ arms, and both.

All models support Narrow or Wide drive-through configurations; choose the desired width

configuration

before

installation based on your specific space or Vehicle width requirements. All

models have Overhead Assemblies and clear floors. All models are ALI certified.

⚠DANGER Be very careful when installing, operating, maintaining, or repairing this equipment;

failure to do so could result in property damage, product damage, injury, or (in very

rare cases) death. Make sure only authorized personnel operate this equipment. All

repairs must be performed by an authorized technician. Do not make modifications

to the unit; this voids the warranty and increases the chances of injury or property

damage. Make sure to read and follow the instructions on the labels on the unit.

More information about the full line of BendPak products is available at bendpak.com.

XPR-10 Series Two-Post Lifts 4P/N 5900951 — Rev. D — May 2019

This manual is mandatory reading for all users

of XPR-10 Series Lifts, including anyone who

installs, operates, maintains, or repairs them. Keep this manual on or near the equipment at all times.

Technical support and service is available from your dealer, on the Web at bendpak.com/support,

by email at techsupport@bendpak.com, or by phone at (800) 253-2363, extension 196.

You may also contact BendPak for parts replacement information (please have the model and serial

number of your unit available) at (800) 253-2363, extension 191.

Shipping Information

Your equipment was carefully checked before shipping. Nevertheless, you should thoroughly inspect

the shipment

before

you sign to acknowledge that you received it.

When you sign the bill of lading, it tells the carrier that the items on the invoice were received in good

condition.

Do not sign the bill of lading until

after

you have inspected the shipment.

If any of the

items listed on the bill of lading are missing or damaged, do not accept the shipment until the carrier

makes a notation on the bill of lading that lists the missing or damaged goods.

If you discover missing or damaged goods

after

you receive the shipment and have signed the bill of

lading, notify the carrier at once and request the carrier to make an inspection. If the carrier will not

make an inspection, prepare a signed statement to the effect that you have notified the carrier (on a

specific date) and that the carrier has failed to comply with your request.

It is difficult to collect for loss or damage after you have given the carrier a signed bill of lading. If this

happens to you, file a claim with the carrier promptly. Support your claim with copies of the bill of

lading, freight bill, invoice, and photographs, if available. Our willingness to assist in helping you

process your claim does not make us responsible for collection of claims or replacement of lost or

damaged materials.

Safety Considerations

Read this entire manual carefully before using your new product.

Do not install or

operate the product until you are familiar with all operating instructions and warnings. Do not allow

anyone else to operate the product until they are familiar with all operating instructions and warnings.

Safety Information

Please note the following:

•XPR-10 Series Lifts are two-post service Lifts.

Use them only for their intended purpose.

•Only operate your Lift between temperatures of 41°F to 104°F (5°C to 40°C).

•The Lift should only be operated by authorized personnel. Keep children and untrained personnel

away from the Lift.

•Do not make any modifications to the Lift; this voids the warranty and increases the chances of

injury or property damage.

•Do not use the Lift while tired or under the influence of drugs, alcohol, or medication.

•Make sure all operators read and understand this Installation and Operation Manual. Keep the

manual near the Lift at all times.

XPR-10 Series Two-Post Lifts 5P/N 5900951 — Rev. D — May 2019

•Make a visual inspection of the Lift before using it. Do not use the Lift if you find any missing or

damaged parts. Instead, take it out of service, then contact an authorized repair facility, your

distributor, or BendPak at (805) 933-9970 or techsupport@bendpak.com.

•BendPak recommends making a

thorough

inspection of the Lift at least once a year. Replace

any damaged or severely worn parts, decals, or warning labels.

Symbols

Following are the symbols used in this manual:

⚠DANGER Calls attention to a hazard that

will

result in death or injury.

⚠WARNING Calls attention to a hazard or unsafe practice that could result in death or injury.

⚠CAUTION Calls attention to a hazard or unsafe practice that could result in personal injury,

product damage, or property damage.

NOTICE Calls attention to a situation that could result in product or property damage.

Tip Calls attention to information that can help you use your unit better.

Liability Information

BendPak assumes no liability for damages resulting from:

• Use of the equipment for purposes other than those described in this manual.

• Modifications to the equipment without prior, written permission from BendPak.

• Damage to the equipment from external influences.

• Incorrect operation of the equipment.

Electrical Information

⚠DANGER All wiring

must

be performed by a licensed, certified Electrician. Do not perform

any maintenance until main electrical power has been disconnected from the Lift

and cannot be re-energized until all procedures are complete.

Important electrical information:

•Improper electrical installation can damage the Power Unit motor, which is not covered by the

warranty.

•The Lift uses electrical energy; if your organization has Lockout/Tagout policies, make sure to

implement them after connecting to a power source.

•Use a separate circuit breaker for each Power Unit.

•Protect each circuit with a time delay fuse or circuit breaker:

–For a 208 to 230 VAC,

single phase

circuit, use a 25 amp fuse.

–For a 208 to 230 VAC,

three phase

circuit, use a 20 amp fuse.

–For a 380 to 440 VAC,

three phase

circuit, use a 15 amp fuse.

XPR-10 Series Two-Post Lifts 6P/N 5900951 — Rev. D — May 2019

Frequently Asked Questions

Question: What kinds of Vehicles can I raise on my XPR-10 Series Lift?

Answer: Cars, trucks, SUVs, and so on; up to 10,000 lbs (4,536 kg) each.

Q: How long will it take to raise or lower my Vehicle?

A: Anywhere from 30 to 45 seconds, depending on how high you raise it.

Q: Does the Lift have to be anchored in place?

A: Yes. Two-Post Lifts

must

be anchored. Your Lift comes with high-quality, Automotive Lift

Institute-certified Anchor Bolts; use only the Anchor Bolts that came with your Lift.

Q: How thick does my Concrete have to be?

A: 4.25 inches thick, 3,000 PSI, cured for a minimum of 28 days. Do not install the Lift on cracked or

defective Concrete.

Do not install on asphalt or any surface other than Concrete

Q: Can I install my Lift outside?

A: No. All XPR-10 Series Lifts are approved for indoor installation and use only.

Q: How long can I leave a Vehicle raised up on my Lift?

A: For a long time, as long as you leave the Lift engaged on its Safety Locks. Once the Lift is

engaged on its Safety Locks, gravity holds it in position.

Only leave your Lift either on the

ground (fully lowered) or engaged on its Safety Locks

Q: How many Safety Lock positions does my Lift have?

A: Fourteen, spaced every 3 inches.

Q: Does the Lift have a Front and Rear?

A: Yes and no. Because you can drive onto a two-post Lift from either opening, there is technically

no Front and Rear. However, most garages have an Approach side and a Wall side, so in that

case, the Wall side is the Front and the Approach side is the Rear. If you have an Asymmetric Lift,

the 30° angle faces the Rear of the Lift, so the other end is the Front.

Q: What is the difference between a Symmetric and an Asymmetric Lift?

A: The Bases of Symmetric Lifts face each other directly and when a Vehicle is on the Lift, it is more

or less balanced; the same amount of weight on either side of an imaginary line drawn between

the Posts. The Bases of Asymmetric Lifts are angled 30 degrees towards the Approach, making it

easier to open the doors of some Vehicles. When a Vehicle is on an Asymmetric Lift, about 30

percent of the weight is in front of the Posts and about 70 percent is behind the Posts.

Q: Are Vehicles on an Asymmetric Lift balanced?

A: Yes. Even though Asymmetric Lifts are angled, the Arms are positioned such that the Vehicle is

still balanced when raised on the Lift.

Q: How do I know where to put the Adapters when I want to raise a Vehicle?

A: The Vehicle needs to be balanced, so you must put the Adapters (sometimes called Pads) so that

they contact the manufacturer’s recommended Lifting Points.

If you do not know where the

manufacturer’s recommended Lifting Points are on a Vehicle, you must find out

before you raise it

. Your Lift came with books that will help: Vehicle Lifting Points for Frame

Engaging Lifts shows the Lifting Points for hundreds of Vehicles. Lifting It Right includes

information about how to raise Vehicles correctly.

XPR-10 Series Two-Post Lifts 7P/N 5900951 — Rev. D — May 2019

Components

Symmetric model shown. Not all components shown. Powerside Post shown on the right. Models with

extension pieces are taller. Asymmetric models are angled 30° towards the Approach side.

XPR-10 Series Two-Post Lifts 8P/N 5900951 — Rev. D — May 2019

XPR-10 Series Lift components include:

•Powerside Post: The Powerside Post holds the Power Unit, the Safety Lock Release Handle,

the Lowering Handle (which is on the Power Unit), and the Power Disconnect Switch. The

Powerside Post must be on the Right (looking at the Lift from the Approach) for Asymmetric

models; it can be on the Left or the Right for Symmetric models.

•Offside Post: The other Post.

•Power Unit: Provides Hydraulic Fluid to the Lift and connects to an appropriate power source.

Includes the Up Button, the Lowering Handle, and the Hydraulic Fluid reservoir.

•Up Button: Press and hold to raise the Vehicle on the Lift.

•Safety Lock Release Handle: Located on the Power Post above the Power Unit, it

disengages the Safety Locks so you can lower the Lift.

•Lowering Handle: Lowers the Lift when used at the same time as the Safety Lock Release

Handle. Located on the Power Unit.

•Power Disconnect Switch: Immediately interrupts main electrical power to the Lift. Used for

electrical circuit faults, emergency situations, or when Lift is undergoing service or maintenance.

•Lift Heads: Sometimes called carriages. Lift Heads move up and down in the Posts. They

connect to the Lift Arms, so when the Lift Heads move up, the Lift Arms also move up, thus raising

any Vehicle on the Lift Arms.

•Lift Arms: Extendable steel arms that attach to the Lift Heads. Adapters (also called Pads) attach

at the end of each Lift Arm; they contact the Lifting Points on the underside of the Vehicle.

•Adapters: Pads that contact the Lifting Points on the underside of the Vehicles you raise. Four

Screw Lift Adapters are included with your Lift, as are a set of four Auxiliary Adapters that can be

used with the Screw Lift Adapters to add an additional 2.5 inches of height (to make better contact

with the Lifting Points on some Vehicles).

Frame Cradle Pads, which are well-suited for raising and holding trucks and SUVs (body-on-frame

style), are available separately.

•Safety Locks: Hold the Lift Heads up when engaged. Multiple Safety Lock heights let you select

the best one for your needs. Once engaged on its Safety Locks, the Lift Heads stay up, even if the

Lift loses power.

Only leave your Lift fully lowered or engaged on Safety Locks.

Safety Locks are pretty well hidden by the Posts, but you can hear them as the Lift rises. Refer to

About Safety Locks for more information.

•Overhead Assembly: The steel beam that sits between the tops of the two Posts, it supports

the Lift’s structure, holds Cables and Hydraulic Lines, and can be set to Wide or Narrow drive-

through Configurations during installation.

•Safety Shutoff Bar: Located on the underside of the Overhead Assembly, the Safety Shutoff

Bar stops upward movement of the Lift if the top of a Vehicle hits it.

•Equalizing Cables: Two cables that keep the Lift Heads synchronized. You do not want one Lift

Head lowering or raising faster than the other Lift Head; the Equalizing Cables keep them

synchronized. For Symmetric Lifts, the two Equalizing Cables are the same length; for Asymmetric

Lifts, the two Equalizing Cables are different lengths.

XPR-10 Series Two-Post Lifts 9P/N 5900951 — Rev. D — May 2019

Specifications

XPR-10 Series Two-Post Lifts 10 P/N 5900951 — Rev. D — May 2019

Model XPR-10S / -LP XPR-10S-168 / -168-LP

Lifting Capacity 10,000 lbs / 4,536 kg

Maximum Capacity Front Axle 5,000 / 2,268 kg

Maximum Capacity Rear Axle 5,000 / 2,268 kg

A– Rise 69" / 1,753 mm

B– Lifting Height w/Pad*73.75" / 1,873 mm

C- Maximum Lifting Height*78.5" / 1,991 mm

D– Minimum Height w/Pad 4.75" / 120 mm

E– Height Overall 144.75" / 3,678 mm 168.75" / 4,284 mm

F– Width Overall (Narrow) 132" / 3,353 mm

F– Width Overall (Wide) 145" / 3,683 mm

G– Outside Posts (Narrow) 126.75" / 3,219 mm

G– Outside Posts (Wide) 139.75" / 3,549 mm

H– Inside Posts (Narrow) 105.5" / 2,679 mm

H– Inside Posts (Wide) 118.5" / 3,009 mm

I– Drive-Thru Width (Narrow) 93" / 2,364 mm

I– Drive-Thru Width (Wide) 106" / 2,694 mm

J– Floor to Top Switch 140.75" / 3,576 mm 164.75" / 4,182 mm

K– Front Arm Reach (min) 25.5" / 646 mm

K– Front Arm Reach (max) 49.5" / 1,255 mm

L– Rear Arm Reach (min) 32.25" / 820 mm

L– Rear Arm Reach (max) 52.5" / 1,333 mm

Motor 220 VAC, 60 Hz, 1 Phase

Time to Full Rise ~45 seconds

Maximum Hydraulic Pressure 2500

Sound <70 dB

*Lifting Height w/Pad is maximum lifting height with Pads at lowest height, no adapter. Maximum

Lifting Height is maximum lifting height with Pads at top height and with the 2.5" / 63 mm Adapter.

Specifications subject to change without notice.

Autres manuels pour XPR-10 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Bend-Pak Système de levage

Bend-Pak

Bend-Pak HD-12LS Manuel utilisateur

Bend-Pak

Bend-Pak PL-6000DC Manuel de référence

Bend-Pak

Bend-Pak HDSO-14P Manuel utilisateur

Bend-Pak

Bend-Pak HD-14T Manuel utilisateur

Bend-Pak

Bend-Pak XPR-10T Manuel utilisateur

Bend-Pak

Bend-Pak HD-9 Manuel utilisateur

Bend-Pak

Bend-Pak EV2400SL Instruction manuelle

Bend-Pak

Bend-Pak HD-9STX Manuel utilisateur

Bend-Pak

Bend-Pak HD-973P Manuel utilisateur

Bend-Pak

Bend-Pak HDS-14LSX Manuel du propriétaire

Bend-Pak

Bend-Pak GP-9XLT Package Manuel utilisateur

Bend-Pak

Bend-Pak HDS-14LSXE Manuel utilisateur

Bend-Pak

Bend-Pak HD-9ST Manuel utilisateur

Bend-Pak

Bend-Pak HD-7P Manuel utilisateur

Bend-Pak

Bend-Pak XPR-10-168 Manuel utilisateur

Bend-Pak

Bend-Pak HDS-18E Manuel utilisateur

Bend-Pak

Bend-Pak HD-9AE Manuel utilisateur

Bend-Pak

Bend-Pak XPR-10XLS-181 Manuel utilisateur

Bend-Pak

Bend-Pak PL-6KDT Manuel utilisateur

Bend-Pak

Bend-Pak LR-5T Manuel utilisateur

Bend-Pak

Bend-Pak XPR-9S Manuel utilisateur

Bend-Pak

Bend-Pak HDS-18E Manuel utilisateur

Bend-Pak

Bend-Pak Clearfloor 10AP Manuel utilisateur

Bend-Pak

Bend-Pak PL-14000 Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur