BEC MX-200 Manuel utilisateur

Quick Install Guide

Attach the Antennas

Remove the plastic dust

caps from the antenna

connectors.

Screw the antennas until

fully attached to the female

connectors of the Cellular

and/or GPS Modules.

LAN - Green: Connected to a Gigabit (1000Mbps) device.

Orange: Connected to a 10/100Mbps device

Blinking: Data being transmitted / received

LTE Signal Strength –Green: RSSI > -69dBm. Excellent

Green / Fast Flashing: -69 > RSSI > -81dBm. Good.

Red / Fast Flashing: -81 > RSSI > -99dBm. Fair.

Red / Slow Flashing: -99dBm > RSSI. Poor

Red: No Cellular signal. Cellular module still in service

Off: No Cellular module or module failure

Internet - Green: IP traffic via WAN

Red: WAN IP request failed

Off: No WAN connection or in Bridge mode

Power - Green: System ready. Red: Boot failure

WHAT’S IN THE BOX

1 x BEC MX-200 M2M Router

1 x This Quick Install Guide

1 x CD containing the User Manual

1 x DIN Rail Mounting Kit

1 x Power Terminal Block 2-Pin 3.5mm

1 x Power Cable with 2-Pin Terminal Block

1 x DC Power Adaptor, 12V 1.2A

(Optional)

3G/4G Antennas

Active GPS Antenna

SETTING UP THE ROUTER

DEVICE OVERVIEW & LEDS

Insert the SIM card

Slide the SIM card (2FF)

with the mental contacts

(gold plate) facing down to

the SIM slot then push it

all the way in until you

hear the clicking sound.

Connect the Serial (RS-232)

Use a RS-232 (DB-9)

male serial adaptor to

connect with industrial

equipment –including

PLC, SCADA, Sensor,

Meters, and Motor.

Access to the MX-200 Web interface by entering http://192.168.1.254

in the address bar of the web browser.

Default Login Information: Username (admin) and Password (admin).

The Quick Start Wizard provides key steps to get the MX-200 on the

Internet.

Connect to the MX-200

1.1 Attach the power

cable with 2-pin terminal

block to the MX-200 and

plug in the supplied power

adaptor

Connect to Power Source

1.2 Attach the power

terminal block (TB) to the

MX-200 and connect the

wire leads of the power

supply cable to the TB plug.

The red wire (power/VCC)

should connect to the

positive terminal and black

wire to the ground (GND) of

the power supply.

Input voltage range is from

9-56V

ATTACHING TO A DIN RAIL REMOVING FROM A DIN RAIL

MOUNTING POSITIONS

Remove MX-200 from a DIN rail.

1-2. Push down the MX-200 to free the bottom of the clip

from the DIN rail.

3. Unhook the top of the clip and pull the MX-200

away from the DIN rail

DIN RAIL MOUNTING

DIN RAIL MOUNTING OPTIONS

KIT CONTAINS: DIN Rail Clip and Six (6) Clip Mounting Screws

The DIN Rail mounting kit is designed to securely attach and clip the MX-200 onto a TS35 or standard 35mm top hat (EN

500022/BS 5584) DIN rail in the horizontal position.

Two (2) mounting locations to mount the DIN rail clip on the surface of MX-200, back or rear side.

Please follow the steps to complete DIN rail mounting installation.

Clip and secure the MX-200 onto a DIN rail.

1. Hook the top of the clip onto the top edge of the DIN

rail. Make sure the clip is firmly against the rail.

2. Push down the bottom of the MX-200 to snap it onto

the lower edge of the DIN rail.

3. The MX-200 is now mounted on the DIN rail.

Attach and fasten the DIN rail clip (known as clip)

to the back or rear side of the MX-200 using two (2) clip

mounting screws included in this mounting kit.

1.MX-200 2.DIN rail clip 3.Mounting Screws

Install clip in either vertical or horizontal position

SUPPORT: Visit us at www.bectechnologies.net.

Autres manuels pour MX-200

Table des matières

Autres manuels BEC Routeur réseau

BEC

BEC M2M MX-1000e Manuel utilisateur

BEC

BEC 7300N Manuel utilisateur

BEC

BEC BEC MX-230 M1 Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

BEC

BEC MX-200A Manuel utilisateur

BEC

BEC 5200 Series Manuel utilisateur

BEC

BEC 7800 Manuel utilisateur

BEC

BEC 5102 Series Manuel utilisateur

BEC

BEC MX-200 Manuel utilisateur

BEC

BEC Ultimum 8700AXL Manuel utilisateur

BEC

BEC MX-221P Manuel utilisateur

BEC

BEC RidgeWave 7000 R26-W Manuel utilisateur

BEC

BEC 7300 Series Manuel utilisateur

BEC

BEC RidgeWave 6900 Manuel utilisateur

BEC

BEC 8800N Manuel utilisateur

BEC

BEC 7800TN Manuel utilisateur

BEC

BEC 7700N Manuel utilisateur

BEC

BEC 7404 Series Manuel utilisateur

BEC

BEC 5200 Series Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

BEC

BEC MX-210NP Manuel utilisateur

BEC

BEC 6600AEL Manuel utilisateur

BEC

BEC BEC 7800(N) Manuel utilisateur

BEC

BEC MX-1200 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur