BEC MX-1200 Manuel utilisateur

BEC MX-1200

(4G/LTE) Gigabit Multi-Service

Broadband Router

Quick Start Guide

BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router

Package Contents

✓BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router * 1

✓This Quick Start Guide *1

✓RJ-45 Ethernet Cable * 1

✓2.4GHz Wi-Fi Antenna (Short) * 2 + 5GHz Wi-Fi Antenna (Long) * 2

✓MiniFIT to DC Power Cable *1

✓DC Power Adapter * 1

✓Mounting Bracket * 1

NOTE:ALL IMAGES SHOWN ARE FOR ILLUSTRATION PURPOSE ONLY.

PACKAGE CONTENTS MAY DIFFER FROM ACTUAL PRODUCTS.

Warning

⚫Do not use the router in high humidity or at high temperature.

⚫Do not use the same power source for the router as other equipment.

⚫Do not open or repair the case yourself. If the router is too hot, turn off

the power immediately and have it repaired at a qualified service center.

⚫Avoid using this product and all accessories outdoors.

Attention

⚫Place the router on a stable surface.

⚫Only use the power adapter that comes with the package. Using a

different voltage rating power adapter may damage the router.

PLEASE READ THE QUICK START GUIDE AND FOLLOW THE

STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU

INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.

IF YOU NEED MORE INFORMATION ON THIS SOFTWARE

CONFIGURATION, PLEASE REFER TO THE ONLINE USER

MANUAL.

Quick Start Guide

Front Panel - Connectors

PORTS

MEANING

(Optional)

LTE 1

(Main/GPS/Aux)

Antenna

Connectors

MX-100U as Primary LTE Connectivity

SMA female connectors

Manually screw the mobile and/or GPS antennas tight to the female connectors for

mobile connection 1

(Optional)

LTE 2

(Main/GPS/Aux)

Antenna

Connectors

MX-1200 Embedded as Secondary LTE Connectivity

SMA female connectors

Manually screw the 3G/4G and/or GPS antennas tight to the female connectors for

mobile connection 2

III

Gigabit

LAN Ethernet

(1 - 4)

Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when

connecting to a PC or an office/home network of 10Mbps /100Mbps /1000Mbps

* LAN 1/EWAN 1 & LAN 2/EWAN 2

Connect to a Fiber/ Cable/ xDSL Modem with using a RJ-45 cable for broadband

connectivity

Note: LAN1 and/or LAN2 automatically becomes an EWAN port when EWAN internet

interface is configured in the management GUI

USB Ports

The USB can support setup for storage/file sharing. Connect an external USB dongle /

hard drive for storage

Power

Connect the supplied Power cable to this jack port

BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router

Front Panel - LEDs

LEDS

MEANING

LTE 1 / LTE 2

(Received

Signal

Strength

Indicator)

Green

RSSI greater than -69 dBm. Excellent signal condition

Green Flashing

quickly

RSSI from -81 to -69 dBm. Good signal condition

Red Flashing

quickly

RSSI from -99 to -81 dBm. Fair signal condition

Red Flashing

slowly

RSSI less than -99 dBm. Poor signal condition

Red

No signal and the 4G LTE module is in service

Off

No LTE module or LTE module fails

GPS

Green

GPS is up and ready to use

USB 1 / USB 2

Green

Connecting to a USB dongle or a hard drive

Internet

Green

Internet is connected, and traffic is passing through the device

Red

IP request failed

Off

Either in bridged mode or WAN connection is not ready

Power

Green

System is up and ready

Red

Boot failure

Gigabit

Ethernet

(LAN 1 - 4)

Green

Transmission speed is at Gigabit speed (1000Mbps)

Orange

Transmission speed is at 10/100Mbps

Blinking

Data being transmitted/received

Quick Start Guide

Back Panel –Wi-Fi Connectors & LEDs

LEDS

MEANING

Wi-Fi 2.4G / 5G

Green

Wireless connection to 2.4G or/and 5G network is established

Blinking

Data being transmitted / received

PORTS

MEANING

2.4GHz

Wi-Fi Antenna

Find two (2) short 2.4GHz Wi-Fi antennas and screw them onto the antenna

connectors

VII

5GHz

Wi-Fi Antenna

Find two (2) long 5GHz Wi-Fi antennas and screw them onto the antenna

connectors

VIII

WPS &

Wireless

On/Off

By controlling the pressing time, users can achieve two different effects:

(1) WPS*: Press &hold the button for less than 6 seconds to trigger WPS function.

(2) Wireless ON/OFF button: Press & hold the button for more than 6 seconds to

enable or disable the wireless.

* Refer to the WPS section in the User Manual for more details.

Reset

After the device is powered on, press it 6 seconds or above: to restore to factory

default settings (this is used when you cannot login to the router, e.g. forgot your

password)

SIM1 / SIM2

Card Slots

Primary: SIM1. Secondary: SIM2

If only have one SIM card, insert it to SIM1.

Insert the mini SIM card (2FF) with the gold contact facing up.

Push the mini SIM card (2FF) inwards to eject it

* Power off the MX-1200 before inserting or removing the SIM card(s)

BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router

Hardware Connection

LTE & GPS

2.4GHz and 5GHz Wi-Fi

Quick Start Guide

Hardware Installation

1. Power Connection

There are two power sources to power on the MX-1200. (1) DC power adapter or (2) Vehicle

Electrical System

A. Using the Supplied DC Power Adapter

Attach the miniFIT-to-DC-Power-Cable to the 4-pin connector of the MX-1200. Then plug in

the supplied power adapter to the wall and the power plug to the DC jack of the power cable to

power ON the MX-1200.

B. Using Vehicle Electrical System

Attach the vehicle hardware power cable to the MX-1200 and connect the wire leads of the

power cable to the vehicle’s electric system

MiniFIT to DC

Power Cable

Vehicle

Power Cable

BEC MX-1200 (4G/LTE) Gigabit Multi-Service Broadband Router

Power PIN Definition

BLACK Wire (PIN 1 & 2): Ground (GND). Use one of the BLACK wires for a neutral or ground

connection

WHITE Wire (PIN 3): ACC/ON for Ignition Input wire need to be connecting into vehicle

accessory wire.

RED Wire (PIN 4): VCC/OFF Voltage wire to the battery. DC power range from 0V to 56V.

2. LAN Connection

Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the other side to

the PC’s Ethernet interface.

3. WAN Link Interface and Connection

BEC MX-1200 supports Internet failover and failback on multiple WAN interfaces, dual EWAN,

Wi-Fi WAN and 4G/LTE (optional) <Please refer to User Manual for detailed Internet setup>

A. Ethernet WAN Connections

MX-1200 supports dual WAN Internet connections; both WANs work simultaneously. Connect

RJ-45 Ethernet cable to one or both EWAN port(s) and connect the other side to another

alternative broadband device, such as Cable Modem, VDSL, Fiber Modem or PON optic line.

Quick Start Guide

B. Wi-Fi Connection (Client Mode)

MX-1200 also supports Wi-Fi as WAN known as Wi-Fi Client. The Wi-Fi client connects to a

remote Wi-Fi Access Point (AP) for remote network or Internet access.

MX-1200 supports both 2.4GHz and 5GHz. Currently, the Wi-Fi client only available in the

2.4GHz band.

C. 4G/LTE Connection (Via MX-100U 4G/LTE Modem)

Insert the MX-100U to the MX-1200

Using the MX-100U, a 4G/LTE modem, to upgrade your existing MX-1200 to support mobile

4G/LTE service.

1) Remove the metal plate.

2) Insert the SIM card(s). MX-100U supports dual-SIM and failover feature.

NOTE: Insert the SIM with gold contact facing up. Make sure that the SIM card has been slid into the

bottom of the slot with a click. When removing the SIM card, press the SIM card again it will be ejected from the

card slot.

3) Insert and firmly attach the MX-100U to the MX-1200.

4) Put and screw the metal plate back to the MX-1200.

Autres manuels pour MX-1200

Table des matières

Autres manuels BEC Routeur réseau

BEC

BEC MX-210NP Manuel utilisateur

BEC

BEC 7404 Series Manuel utilisateur

BEC

BEC 7300N Manuel utilisateur

BEC

BEC 7300 Series Manuel utilisateur

BEC

BEC MX-1000 Manuel utilisateur

BEC

BEC MX-200A Manuel utilisateur

BEC

BEC BEC 6500AEL Manuel utilisateur

BEC

BEC RidgeWave 7000 R26-W Manuel utilisateur

BEC

BEC MX-200 Manuel utilisateur

BEC

BEC 5200 Series Manuel utilisateur

BEC

BEC 6600AEL Manuel utilisateur

BEC

BEC RidgeWave 6900 Manuel utilisateur

BEC

BEC 5102 Series Manuel utilisateur

BEC

BEC BEC MX-230 M1 Manuel utilisateur

BEC

BEC 5200 Series Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

BEC

BEC Ultimum 8700AXL Manuel utilisateur

BEC

BEC MX-200 Manuel utilisateur

BEC

BEC 7700N Manuel utilisateur

BEC

BEC MX-1200 Manuel utilisateur

BEC

BEC 4700A Manuel utilisateur

BEC

BEC 7800 Manuel utilisateur

BEC

BEC BEC 7800(N) Manuel utilisateur

BEC

BEC 7700N Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur